Hoover Turbo POWER Upright Vacuum Cleaner инструкция обслуживания

® This product was designed for easy assembly (see page 3) www .hoover .com ENGLISH ➜ pp.1-13 ESP AÑOL ➜ pág. 14-21 FRANÇAIS ➜ p. 23-30 Owner’ s Manual Thank you for your pur chase! T urboPOWER TM Upright V acuum Cleaner by HOOVER TM[...]

2 Thank you for choosing a HOOVER pr oduct. Please enter the COMPLETE model and serial numbers in the spaces provided. The numbers are located on the back of your cleaner . Model_________________________________________ Serial number_________________________________________ Hint: Attach your sales receipt to this owner ’s manual. V erification of[...]

3 1. Assembly If you need any assistance: V isit our website at www .hoover .com . Click on the “Service” button to find the service outlet near est you OR Call 1-800-944-9200 for an automated r eferral of service outlet locations (U.S. only) OR Call 1-330-499-9499 to speak with a r epresentative in our Consumer Response Center . Please do not [...]

4 1-6 1-7 1. Handle 2. Custom Control™ power switch 3. Custom Control™ indicator 4. T ool cover 5. Dusting brush 6. Pre-filter 7. HEP A cartridge filter 8. Headlight 9. Furniture guard 10. Nozzle control knob: tur n knob to correct setting for height of carpet being cleaned. 1 1. Final filter 12. Dirt cup 13. Dirt cup handle 14. Powered hand to[...]

5 Continued ➜ A 2-3 2-4 2-5 Carr ying cleaner Use the carrying handle to lift the cleaner . Do not lift cleaner using dirt cup handle (A). Handle positions The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating posi- tion for general operation on carpet and floors; low for reaching under low f[...]

2-11 Stair cleaning Use the hose and powered hand tool or furniture nozzle for stair cleaning. CAUTION: T o prevent the cleaner from falling, always place it at the bottom of the stairs. With handle in upright position, clean from bottom to top. Select proper tool A. Dusting brush may be used for carved furniture, table tops, books, lamps, lighting[...]

7 How to attach tool cover The tool cover is designed with a “break- away” feature which allows it to snap fr ee if it is pushed open too far . T o r eattach, align hinges of cover with slots on sides of tool storage area. Push cover down to secure in place. 2-14 Continued ➜ The dirt cup assembly consists of the following parts: Lid (A) Dirt [...]

3-13 Disconnect cleaner from electrical outlet. Step on handle release pedal and place cleaner in the lowest position. T urn cleaner over . Using a Phillips screw- driver , remove the two scr ews (A) locat- ed nearest the wheels at the r ear of the base of the cleaner . Headlight replacement What to buy This cleaner uses a 12 volt, wedge base type [...]

9 Install bulb - Pull old bulb straight out of socket. Push new bulb straight into socket until locked in place Excessive force is not required. Replace hood - Reposition hood, fit- ting tabs (A) on either side under the lens cover as shown. Replace screw and HOOVER® emblem. T urn cleaner over and replace the two scr ews located on the bottom of t[...]

10 3-29 3. Remove agitator including end plates (C) and discard. 4. Inspect belt to ensure that it is in good condition. If belt is cracked, gouged or broken, r eplace it (see follow- ing section). 5. Insert brush roll through belt and posi- tion belt over gear teeth (D) on brush roll. C D 3-27 A Power ed hand tool Agitator brush roll replacement W[...]

11 3-30 3-32 3-31 E 6. With curved ends down, slide end plates (C) of brush roll into slots (E) on tool. 7. Replace belt guard (B) making sur e not to pinch brush bristles in guard. T ur n agitator , to make sure it r otates freely . Replace and tighten screws. 8. T o r eplace bottom plate (A), inser t the four tabs on edge of bottom plate into slo[...]

12 Lubrication The cleaner is equipped with bearings that contain sufficient lubrication for the life of the cleaner . The addition of lubri- cant could cause damage. Therefore, do not add lubricant to any bearings. • Pre-filter clogged • Clean pre-filter as described in “Filter assembly” section. • Dirt cup not properly installed • Pos[...]

13 Ser vice T o obtain appr oved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Sales and Service Center or Authorized Hoover W arranty Service Dealer (Depot) by: • checking the Y ellow Pages under “V acuum Cleaners - Household” OR - • checking the list of Sales and Ser - vice Centers provided with this cleaner OR - • [...]