HP (Hewlett-Packard) 2995 инструкция обслуживания

Instructions for Installation and Operation 3 PHASE AC MOTOR SPEED CONTROL 3 PHASE AC MOTOR SPEED CONTROL 3 PHASE AC MOTOR SPEED CONTROL 3 PHASE AC MOTOR SPEED CONTROL     Model 2995, for 115/230 VAC power supply, with NEMA 4 enclosure and lin e filter fo r CE Mark P/N 074 01040 B (DX)[...]

2 QUICK REFERENCE This manual contains the basic information needed to install and operate Bodine PACESETTER TM 115/230V “NEMA 4” series inverter model 2995. This manual does not profess to cover all details or variations in equipment, nor to provide for every possible contingency associated with installation, operation, or maintenance. No warr[...]

3 TA BLE OF CONTENTS PA GE QUICK REFERENCE 2 PRODUCT SPECIF ICA TIONS 4 IMPO RTANT SAFETY PRECAUTIONS 5 INSTA LLA TION 6 Step 1 – Exam ine Befor e Installation 6 Step 2 – Choose a Suitable Location 7 Step 3 – Mount the Control 7 CONNECTION 8 Step 4 – Prelim inary Setup 8 Step 5 – Connect Motor 10 Step 6 – Install Fus e 11 Step 7 – Con[...]

4 PRODUCT SPECIFICAT IONS A BOUT T HIS PRODUCT - Bodine’s PACESET TER TM “ NEMA 4” ser ies inverter is des igned to provide variable speed c ontrol of s tandard three- phase AC induction m otors . Adjustable linear acceler ation and deceleration are pr ovided, m aking the drive suitable for soft start applications. T he output voltage is sine[...]

5 IMPORTANT SA FETY PRECA UTIONS Model 2995 has been ev aluated by Underw riters Laboratories for conformance to UL standards 508 and 50 and CSA standard C22.2 No. 14 and bears the UL Recognized Component mark. The AC Dr ive is a power electronic dev ice. For safety reasons, please read through this operations manual in detail and observe those par[...]

6 INSTA LLA TION This contr ol should only be installed by a qualified pers on fam iliar with its operation and assoc iated hazards. The National Electrical Code (NEC), loc al electrical and s afety codes, and when applicable, the O ccupational Saf ety and Health Act (OSHA) should be observed to reduc e hazards to personnel and property. Step 1. Ex[...]

7 Step 2. Choose a Suitable Location The installation site directly impacts the functionality and lifespan of the control.  Avoid areas w here surrounding air temperature exceeds 40 O C (direct sunlight or near heating equipment or inside a panel without a cooling fan.  Avoid locations w here the front panel dial and switch may be bumped and [...]

8 CONNECTION CA UTION  The PCB inside the inverter enclosure is vulnerable to static electr ical charges. Avoid contact with the PCB.  Choose an appr opriate power source with correct voltage sett ings f or the specif ication of the AC inverter .  Do not use a separate device between control and motor t o switch motor ON or OFF during oper[...]

9 In this mode, the motor will produce full rated torque up to 60 Hz. Above 60 H z, torque will linearly reduce to 50% at 120 Hz. Figure 6 - Graph showing reduction in motor torque at frequencies above 60 Hz. AC LINE VOLTA GE SELECTOR JUMPERS – There are three v oltage selector jumpers that must be repositioned if the input line voltage is 230 VA[...]

10 Step 5 – Connect th e Motor A cord should be used for the motor connection in order to properly seal the liquid tight fitting. The fitting w ill accept cord diameters betw een 0.17” and 0.47” diameter. The length of the cord should be kept short for minimum voltage drop and only copper wire w ith 60 O C rated insulation should be used. Loo[...]

11 Figure 8 - Connection diagram for Bodine 230V inverter-duty motors. Figure 9 - Connection diagram for Bodine 230/460V i nverter-duty motors wi red for 230V operation. Table 3 - Direction of B odine motor driveshaft rotation, view ing end of driveshaft, w hen connected per the diagrams at the left and w ith control set for “forward” di rectio[...]

12 OPERA TION Step 9 – Check Sy stem Before Starting WA RNING  Recheck all connections.  Do not open the cover of the inverter when the power is ON to avoid injury caused by electrical shock .  Do no t attempt to w ire circuitry wh ile p owe r is on. CA UTION  Do not attem pt to mak e or break connections between motor and invert er w[...]

13 Step 10 – Operate the Inv erter The PACESETT ER TM “NEM A 4” series inverter is operated using the switches and speed dial on the front panel of the control. See Figure 10 for panel layout. 1) T urn the AC power ON using the toggle switch. T he power lamp w ill illuminate. 2) Turn the direction sw itch to either the “forward” or “rev[...]

14 MIN : Min i mu m S pe ed The MI N trim pot is used to set the minimum output frequency of the drive, which sets the minimum motor speed. The minimum speed is factory set to 10 Hz. R eadjust the trim pot as follows: 1. Rotate main speed potentiometer to the minimum speed position (full counterclockwise). 2. Increase setting of MIN trim pot so tha[...]

15 DEC/B: Deceleration (w ith 60 Hz or 120 Hz conf iguration) The DE C/B trim pot sets the time it w ill take the motor to reach zero speed from an initial full speed setting. The trim pot is factory set to approx imately 1.5 seconds. Adjust the trim pot as required for the application. Application Note: O n applications with high inertial loads, t[...]

16 CL: Current Limit with I 2 t Shutdown The CL trim pot is used to set the max imum motor current that occurs in a stalled condition. T he C L trim pot is factory set to approx imately 160% of full control rating (3.8 amps). The CL trim pot can be readjusted as required. The current limit also contains an I 2 t trip function. The control w ill tri[...]

17 TROUBLESHOOTING WA RNING  Do not remove the cover of the inverter when the power is ON to avoid injury caused by electrical shock . This control does not require maintenance under normal conditions. If you encounter a problem, read all instructions provided w ith this control and double- check the wiring. If problems persist, contact your sou[...]

18 Figure 13 – Location of LED Status Indicators inside t he enclosure LED STATUS INDICATORS – Models 2995 contains two LE D status indicators on the printed circuit board inside the enclosure. One LED is a green Pow er On indicator (PW R) that indicates the presence of the bus voltage and the operation of the main control logic power supply . [...]

19 DECLA RA TI ON OF CONFORM ITY We, the Bodine Electric Company, 2500 W. Bradley Place, Chicago, Illinois, U.S.A., phone (773) 478-3515, fax (773) 478-3232, declare under our sole responsibility that the following products: Ty pe HPP-5337E4 AC Motor Speed Control, Model number 2995 Are in conformity with the following standards when installed in a[...]

20 BODINE LIM I TED WA RRA NTY The Bodine E lectric Company w arrants all products it manufactures to be free of defects in workmanship and materials w hen used under Normal Operating Conditions and w hen applied in accordance with nameplate specifications. W hen Bodine motors and gearmotors have been purchased with and used only with appropriately[...]