HP (Hewlett-Packard) AT496AV-CTO инструкция обслуживания

Maintenance & Service Guide HP Compaq 6005 Pro Business PC[...]

© Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are trade marks of Microsoft Corporation in the U.S. and other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such prod uct[...]

About This Book WARNING! Text set off in this manner in dicates that failure to follow di rections could result in bodily harm or loss of life. CAUTION: Text set off in this manner in dicates that failure to follow direction s could result in damage to equipment or lo ss of information. NOTE: Text set off in this manner p rovides important suppleme[...]

iv About This Book[...]

Table of contents 1 Product Features Microtower Chassis ............. .......... ........... ............ .......... ........... ........... .......... ........... ......... ........ .......... 1 Standard Configuration Features .................. ............. .............. ............... ............. ............... . 1 Front Panel Components .[...]

Acces sing HP Vi sion Diagnos tics . ............ ............ ............ ............ ............ ........... .......... .... 28 Survey Tab ............ ............. ................ .............. ............... .............. ............... ............... .. .... 29 Test Tab ................ ............... .............. ............... [...]

HP Web S ite Sup port .. ........... ............ ........... ........... ........... ........... ............ ......... ............ ..... .. ......... ... 50 Indust ry Stand ards . ........... ............ ........... .......... ............ ......... ........... ........... ........... ......... ......... ........ 50 Asset Tracking and Security [...]

Personal Grounding Methods and Eq uipment ............... ............. ............ .......... ......... ........ 67 Grounding th e Work Area ... ........ .......... ............ ........... .......... ............ ........... .......... ........... 68 Recommended Materials an d Equipment .... ............. ............... .............. .........[...]

Power S upply ........... .......... ........ ............ .......... ........... ............ .......... ........... ........... ........ .... ............ . 111 System B oard ......... ........... ........... ........... .......... .......... ........... .......... ........... ............ ........ ...... ........... 112 Batter y ........... ....[...]

Type 1 B attery Ho lder ...... ............. ........... ............. ............. .............. ............. .............. ..... 16 6 Type 2 Battery Holder ............ ............ .......... ............ ............ .......... ............ ........... ........... 16 6 Type 3 Battery Holder ............ ............ .......... ............ [...]

Solving Po wer Prob lems ..... ............ ............ ......... ............ ............ ........... ............ ............ ....... .......... 204 Solving H ard Drive Problems ........... ............ ......... .............. ........... ............ .............. ........... ..... .. ...... 205 Solving Media Card Re ader Prob lems ... ....[...]

xii[...]

1 Product Features Microtower Chassis Standard Configuration Features The HP Compaq Microtower featu res may vary depending on the model. Fo r a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Instructi ons for usin g the utility are provided in the Trouble[...]

Front Panel Components Drive configuration may vary b y model. Table 1- 1 Front Panel Components 1 5.25-inch Optical Drives 1 6 Optical Drive Eject Buttons 2 Optical Drive Activity Lights 7 3.5-inch Media Card Reader (optional) 2 3 Hard Drive Activity Light 8 Dual-State Power Button 4 Microphone/Headphone Connector 9 Power O n Ligh t 5 USB (Univers[...]

Media Card Reader Components The media card reader is an opti onal device available o n some mode ls on ly. Refer to the following illustration and table to identify th e media card reader components. Figure 1 -2 Media Card Reader Components Table 1-2 Media Card Reader Components No. Slot Media 1 xD ● xD-Picture Card ( xD) 2 MicroSD ● MicroSD ([...]

Rear Panel Components Table 1- 3 Rear Panel Components 1 Power Cord Con nector 6 Line-Out Connector for powered au dio devices (green) 2 Line-In Audio Connector (blue) 7 PS/2 Keyboard Connector (purple) 3 PS/2 Mouse Connector (green ) 8 VGA Monitor Connector 4 Serial Connector 9 DisplayPort Monitor Connector 5 RJ-45 Network Connector 10 Universal S[...]

Serial Number Location Each computer has a un ique serial number and prod uct ID number that are located on the top cover of the computer. Keep these nu mbers available for use when contacting customer service for a ssistance. Figure 1 -3 Serial Number and Product ID Locatio n Microtower Chassis 5[...]

Small Form Factor Standard Configuration Features The HP Compaq Small Form Factor features may va ry depen ding on the model. For a complete listing of the hardware and software inst alled in the computer, run the di agnostic utility (included on some computer models only). Instructions for using th e utility are provide d in the Troubleshooting Gu[...]

Front Panel Components Drive configuration may vary by mo del. Figure 1 -5 Front Panel Compon ents Table 1-4 Front Panel Components 1 5.25-inc h Optical Dri ve 1 6 USB (Universal Serial Bus) Ports 2 Optical Drive Activity Light 7 Microphone/Headphone Connector 3 Optical Drive Eject Button 8 3.5-inch Media Card Reader (optional) 2 4 Dual-State Power[...]

Media Card Reader Components The media ca rd reader is an optiona l device available on some models only. Refer to the following illustration and table to identify the media card reade r components. Figure 1-6 Med ia Card Reader Co mponents Table 1- 5 Media Card Re ader Components No. Slot Media 1 xD ● xD-Picture Card (xD) 2 MicroSD ● MicroSD ([...]

Rear Panel Components Figure 1 -7 Rear Panel Components Table 1-6 Rear Panel Components 1 RJ-45 Network Connector 6 DisplayPort Monitor Connector 2 Serial Connector 7 VGA Monitor Connector 3 PS/2 Mouse Connector (green) 8 PS/2 Keyboard Connector (purple) 4 Power Cord Connector 9 Line-Out Connector for powered a udio devices (green) 5 Universal Seri[...]

Serial Number Location Each computer has a u nique serial number and product ID number in th e location shown below. Keep these numbers available for use when co ntacting customer service for assistan ce. Figure 1-8 Seri al Number and Product ID Location 10 Chapter 1 Product F eatures[...]

2 Installing and Customizing the Software If your computer was not shipped with a Micro soft op erating system, some portions of this documentation do not apply. Additional informat ion is available in online help after you install the operating system. NOTE: If the computer was shipped with Win dows Vista or Windows 7 loaded, you will be prompted [...]

Installing the Operating System The first time you tur n on the computer, t he operat ing system is installed au tomatically. This process takes about 5 to 1 0 minutes, depending on which op e rating system is being installed. Carefully read and follow the inst ructions on the sc reen to complete the installat ion. CAUTION: Once the automatic insta[...]

Accessing Disk Image (ISO) Files There are disk image files (ISO files) included on yo ur PC that co ntain the installation so ftware for additional so ftware. These CD image files are located in the folder C:SWSetupISOs. Each .iso file can be burned to CD media to create an installation CD. It is recomme nded that these disks be created and the [...]

3 Computer Setup (F10) Utility Computer Setup (F10) Utilities Use Computer Setu p (F10) Utility to do the following: ● Change system default setting s. ● Set the system date and time. ● Set, view, change, or verify the system configurat ion, including set tings for processor, graphics, memory, audio, stora ge, communications, and i nput devic[...]

● Replicate the system setup by saving system conf iguration information on USB flash media device or other storage media emulating a diskette and restoring it on one or more computers. ● Execute self-tests on a sp ecified ATA hard drive (when supported by drive). ● Enable or disable DriveLock secu rity (when supported by drive). Using Comput[...]

Computer Setup—File NOTE: Support for sp ecific Computer Setup opti on s may vary depen ding on the hardwa re configuration. Table 3- 2 Computer Setup—File Option Description System Information Lists: ● Product name ● SKU number (some models) ● Processor type/speed/stepping ● Cache size (L1/L2/L3) ● Installed memory size/speed, number[...]

Computer Setup—Storage NOTE: Support for spe cific Computer Setup op tions may vary depen ding on the hardware configuration. Table 3-3 Computer Setup—Stor age Option Description Device Configuration Lists all in stalled BIOS-controlled storage devices. When a device is selected, detailed informatio n and options are displayed. The following op[...]

Option Description Storage Options Removable Media Boot Enables/disables ability to boot the system from removable media. eSATA Port Allows you to enable eSATA support. This cau s es one of the SATA connectors to become eSATA capable. Max eSATA Speed Allows you to choose 1.5 Gbps or 3.0 Gbps as the maximum eSATA speed. By default, the speed is limi[...]

Option Description DPS Self-Test Allows you to execute self-tests on ATA hard dr ives capable of p erforming the Drive Protection System (DPS) self-tests. NOTE: This selection will only appear when at least one drive capable of pe rforming the DPS self-tests is attached to the system. Boot Order Allows you to: ● Specify the order in which attache[...]

Computer Setup—Security NOTE: Support for sp ecific Computer Setup opti on s may vary depen ding on the hardwa re configuration. Table 3- 4 Computer Setup—Security Option Description Setup Password Allows you to set and enable setup (a dministrator) password . NOTE: If the setup password is set, it is requir ed to change Computer Setup options,[...]

Option Description Device Security Allows you to set Device Available/Device Hidden for ● Serial ports ● Parallel port ● System audio ● Network co ntroller s (some models ) ● Embedded security device (some models) ● SATA0 ● SATA1 ● SATA2 ● SATA3 USB Security Allows you to disable individual or groups of USB ports. Slot Security Al[...]

Option Description System Security (some models: these options are hardware dependent) Data Execution Prevention (some models) (enable/di sable) Helps prevent operating system security breaches. Virtualization Technology (s ome mode ls) (enable/disable) Contr ols the virtualization features of the processor. Changing this se tting requires turning [...]

Computer Setup—Power NOTE: Support for spe cific Computer Setup op tions may vary depen ding on the hardware configuration. Table 3-5 Computer Setup—Power Option Description OS Power Management ● Idle Power Savings—Extended/Normal. Allows certain operating systems to decr ease the processors power con sumption when the processor is idle. ?[...]

Computer Setup—Advanced NOTE: Support for sp ecific Computer Setup opti on s may vary depen ding on the hardwa re configuration. Table 3- 6 Computer Se tup—Advanced (for advanced use rs) Option Description Power-On Options Allows you to set: ● POST mode (QuickBoot, Clear Memory, FullBoot, or FullBoot Every x Days). ◦ QuickBoot = Do not clea[...]

Option Description ◦ Clear Memory = No memory count on cold boot. Clears memory on all boots. ◦ FullBoot Every x Days = Memory count on 1 st cold boot on or after the xth day. No more memory counts until 1st cold boot on or after x days. Clears memory on all boots. ● POST messages (enable/disable). ● F9 prompt (enable/disable or hi dden/dis[...]

Option Description PCI Devices ● Lists currently installed PCI devices and their IRQ setting s. ● Allows you to reconfigure IRQ settings for thes e devices or to disa ble them entirely. These settings have no effect under an ACPI-base d operating system. PCI VGA Configuration Displayed only if there are one or more PCI grap hics controllers in [...]

Option Description from being used by the operating system and reduces the power used by the compu ter in S5. ● Processor cache (enable/disable). ● Multi-Processor (enable/disable). This option may be used to disa ble multi-processor support under the OS. ● Integrated Graphics Memory Size (Automatic , 32M, 64M, 128M, 256M). This allows the us[...]

4 Computer Diagnostic Features Hewlett-Packard Vision Diagnostics NOTE: HP Vision Diagnostics is included on CD with some comp uter models only. The Hewlett-Packard Vision Diagn ostics utility allows you to view information about the hardware configuration of the computer and perform hardwa re di agnostic tests on the subsystems of the computer . T[...]

NOTE: If the system does not b oot to the CD in the optical drive or to the USB flash drive, you may need to change the boot order in the Computer Setup (F10) utility. Refer to the Computer Setup (F10) Utility Guide for more information. 5. At the boot menu , select either the HP Vision Diagnostics util ity to te st the vari ous hardwa re component[...]

There are thre e types of tests to cho ose from: ● Quick Test —Provides a prede termined script where a sa mple of each hardw are component is exercised. You may further modify wh ich of the Quic k tests are executed by selectin g or deselecting individual tests in the h ardware component check list. ● Complete Test —Provides a p redetermin[...]

History Tab The History tab contains in format ion on past test exec utions. The History Log disp lays all tests that have been exec uted, th e number of times of execut ion, the number of times failed, the date each test was e xecuted, and the time i t took to complete ea ch test. The Clear History button will clear the cont ents of the History Lo[...]

The Memory test tab se ction provides informa tion on the HP Memory Test applica tion that may be launched fro m the boot menu. The HP Support section provide s information on obtaining technical support from HP. Saving and Printing Informat ion in HP Vision Diagnosti cs You can save the information di splayed in the HP Vision Diagnostics Su rvey ,[...]

5 Desktop Management HP Client Management Solution s provides stan dards-based solutions fo r managing and controlling desktops, workstations, and n otebook PCs in a networked environ ment. HP pioneered desktop manageabili ty in 1995 with the introduction of the industry’s first fully manageab le desktop personal computers. HP is a patent holde r[...]

The best deplo yment method depe nds on your in formation technology environment and processes. ROM-based setup and ACPI hardware provide furthe r assistance wit h recove ry of system software, configuration man agement and troubleshooting, and power management. HP Client Automation Agent The managemen t agent used by bo th HP Client Auto mation St[...]

● Reports ● Administrative tasks to up date HP sp ecific tools HPCM can be downloade d from http://www.symantec.com/ busine ss/theme.js p?themeid=altiris by clicking on HP Client Mana ger under Strategic Part ner Products . A free perma nent license can also be obtained from the download pa ge. HPCM “How to” videos are also published o n ht[...]

● HP Proactive Change Notification ● HP Subscriber's Choice HP Client Management Interface Regardless of the system management tools your IT department uses, managin g both your hardware and software assets is important to keeping your IT costs low and your business agile. The IT administrator ca n access the HP Client Management In terfac[...]

central file store. SSM then automa tically updates any down-revision system software on the networked PCs to the later levels available in the file store. Since SSM only allows distribution of SoftPaq updates to the correct client system models, administrators can confidentl y and efficient ly use SSM to keep system software updated. System Softwa[...]

HP Client Automation Star ter and Standard Editions HP Client Automation is a hardware and software manag ement solution fo r Windows Vista, Windows XP and HP Thin Client en vironments that is easy to use and quick to deploy, wh ile providing a stron g foundation for future requirements . It is offered in two editi ons: ● The Starter Edition is a[...]

● Remotely configur e BIOS and security settings ● Automate pr ocesses to quickly reso lve hardware problems Tight integra tion with HP Instant Suppo rt t ools reduces ha rdware trouble shooting time. ● Diagnostics—remotely run & vie w reports on HP desktop, note book, and workstation models ● System Health Scan—check for known hard[...]

Microsoft produ cts supported by the HP Client Catalog include: ● System Center Config uration Mana ger 2007 ● System Center Esse ntials 2007 ● Systems Management Server (SMS) 2 003 R2 For more information on HP C lient Catalog for SMS, visit http://h20331.www2.hp.com/ Hpsub/cache/ 486247-0-0-225-121.ht ml?ju mpid=reg_R1002_USEN . Remote Mana[...]

Available managemen t technologies include the fo llowing: ● AMT (includes DASH 1.0) ● ASF ● DASH 1.1 (using a Br oadcom NIC) ASF and AMT may not be configu red at the same time, but bo th are supported. To configure Inte l vPro systems for AMT or ASF: 1. Turn on or restart the compu ter. If you are in Microsoft Windows, click Start > Shut[...]

◦ Password Policy ◦ Secure Firmware Up date (enable/disable) ◦ Set PRTC ◦ Idle Timeout ● Change Intel ® ME Password (HP highly recommen ds that this password be changed. Th e default password is admin .) In order to remotely manage AMT systems, the admini strator must use a rem ote console th at supports AMT. Enterprise manageme nt conso[...]

Retired Solutions Two software packages, Altiris Loc al Recovery, and Dantz Retrospect, wi ll no longer be shipping on HP business desktops, notebooks, or workstations. ROM Flash The computer's BIO S is stored in a pro grammable flash ROM (read onl y memory). By establishing a setup password in the Computer Se tup (F10) Utility, you can protec[...]

Boot Block Emergency Recovery Mode Boot Block Emergency Recovery Mode permits system recovery in the unlikely event of a ROM flash failure. For example, if a p ower failure were to occur during a BIOS upgrade, the ROM flash wo uld be incomplete. This would render the system BIOS unusable. The Boot Block is a flash-protected section of the ROM that [...]

Replicating the Setup The following procedures gi ve an administrator the abilit y to easily copy one setu p configuration to other computers of the same mo del. This allows for fa ster, mo re consistent co nfiguration of multiple computers. NOTE: Both procedures require a diskette dr ive or a supported USB flash drive. NOTE: System Software Manage[...]

NOTE: A bootable diske tte is required for this pro ced ure or to create a bootable USB flash media device. If Window s XP is not available to use to crea te a bootable diskette, use the method for copying to a single computer inste ad (see Copyi ng to Single Computer on page 45 ). 1. Create a bootable d iskette or USB flash media device. See Suppo[...]

To create a boo table USB flash m edia device, you must have: ● a supported USB flash m edia device ● a bootable DOS diskette with t he FDISK and SYS pr ograms (If SYS is not available, FORMAT may be used, but all e xisting files on t he USB flash media device wi ll be lost.) ● a PC that is bootable fr om a USB flash media device CAUTION: Som[...]

12. Copy any fi les you saved in step 9 back to your USB flas h media device. 13. Remove the diskette and reboot the computer. The computer will boot to the USB flash media device as drive C. NOTE: The default boo t order varies fr om compute r to computer, and it can be changed in the Computer Setu p (F10) Utility. If you have used a DOS version f[...]

9. If the system did not au tomatically restart when exiting FDISK, press Ctrl + Alt + Del to reboot to the DOS diskette. 10. At the A: prompt, type FORMAT C: /S and press Enter . Format will format the USB flash media device, add the system files, and ask for a Volume Label. 11. Press Enter for no label or enter one if desired. 12. Turn off the c[...]

HP Web Site Support HP engineers rigorously te st and debug so ftware developed by HP an d third-party suppliers, and develop operating system specific support software, to ensure perform ance, compatibility, and reliability for HP computers. When making the transition to new or revised op eratin g systems, it is importan t to implement the supp or[...]

Use the following utilities to manage security settings on th e HP computer: ● Locally, using the Computer Setup Utilities. See the Computer Setup (F10) Ut ility Guide includ ed with the computer for additional information an d instructions on usi ng the Computer Setu p Utilities. ● Remotely, using HP Client Manager from Symantec, HP Client Aut[...]

Device Security Allows you to set Device Available/Device Hidden for: ● Serial ports ● Parallel port ● Rear USB por ts ● Front USB ports ● Internal USB ports ● System audio ● Network controllers ( some models) ● Legacy diskette ● Embedded security device (some models) ● SATA0 ● SATA1 (some models) ● SATA2 (some models) ● S[...]

Setup Security Level Provides a method to allow end-users limited acce ss to change specified setup options, without having to know the Setup Password . This feature allows the administrator the flexibili ty to protect changes to essential setup options, while allowing the user to view system settings and configure non essential options. The admini[...]

Password Security The power-on password prevents un authorized use of the computer by requiring entry of a password to access applications or data each time the compu t er is turned on or restart ed. The set up password specifically prevents unau thorized access to Compute r Setup, and can al so be used as an overrid e to the power-on passwo rd. Th[...]

Entering a Power-On Password To enter a power-on password, co mplete the following steps: 1. Turn on or restart the compu ter . If you are in Windows, click Start > Shut Down > Restart the Computer . 2. When the key icon appears on the monitor, type the curren t password, then press Enter . NOTE: Type carefully; for security rea sons, the cha[...]

NOTE: Type carefully; for se curity reasons, the chara cters you type do not appear on th e screen. 4. Press Enter . The new password takes e ffect the next time you turn on the computer. NOTE: Refer to th e National Keyboard Del imiter Characters on page 56 for informat ion about the alternate delimiter charac ters. The power-on password and setup[...]

National Keyboard Delimiter C haracters - German - Portuguese * For Bosnia-Herzegovina, Croatia, Montenegro, Serb ia, and Slovenia Clearing Passwords If you forget the password, you cannot access the computer. Refer to the Troubleshooting Guide for instructions on clea ring passwords. If the system is eq uipped with an emb edded security device, re[...]

DriveLock Applications The most practical use of the DriveLock secur ity feature is in a corporate environment. The system administrator would be responsible for con figuring the hard drive which would involve, among other things, setting the DriveLock master password and a temporary us er password. In the event that the user forgets the user passw[...]

3. Select Security > Smart Cover > Cover Removal Sensor , and select the desired security level. 4. Before exiting, click File > Save Changes a nd Exit . Smart Cover Lock The Smart Cover Lo ck is a software-controllable cove r lock featured on some HP computers. This lock prevents unauth orized access to the internal comp onents. Computers[...]

CAUTION: The Smart Cover FailSafe Key is a spec ialized tool available from HP. Be prepare d; order this key before you nee d one at an authorized reseller or ser vice provider. To obtain the Fa ilSafe Key, do any one of the foll owing: ● Contact an authorized HP re seller or service provider . ● Call the appropri ate number listed in the warra[...]

Thermal Sensor The thermal sensor is a hardware and softw are feat ure that tracks the internal temperature of the computer. This feature di splays a caution message when the normal ra nge is exceeded, which g ives you time to take acti on before internal co mponents are d amaged or data is lost. CAUTION: A high temperatur e condition can result in[...]

6 Serial ATA Drive Guidelines and Features NOTE: Serial ATA = SATA HP only supports the u se of SATA hard drives on the se computers. SATA Hard Drives Serial ATA Hard Drive Characteristics Number of pins/conductors in data cab le 7/7 Number of pins in power cable 15 Maximum data cable length 39.37 in (100 cm) Data interface voltage differential 400[...]

SATA Hard Drive Cables SATA Data Cable Always use an HP approved SATA 3.0 Gb/s cable as it is fully backwards comp atible with the SATA 1.5 Gb/s drives. Current HP desktop products shi p with SATA 3.0 Gb/s hard drives. SATA data cables are suscept ible to damage if overfle xed. Never crease a SATA data cabl e and never bend it tighter tha n a 30 mm[...]

ATA SMART Drives The Self Monitoring Analysis a nd Recording Tech nology (SMART) ATA drives for the HP Personal Computers have built-in drive failure prediction th at warn s the user or net work administrator of an impending failure or crash of the hard drive. Th e SMART drive tracks fault p rediction and failure indicati on parameters such as real[...]

7 Identifying the Chassis, Routine Care, and Disassembly Preparation This chapter provides gen eral service information for the computer. Adherence to the procedures an d precautions de scribed in this chap ter is essential for proper service. CAUTION: When the computer is plu gged into an AC power sour ce, voltage is always applied to the system b[...]

Microtower (MT) Electrostatic Discharge Information A sudden discha rge of static electrici ty from your finger or oth er conductor can destroy static-sensitive devices or microcircuitry. Often the spark is neithe r felt nor heard, but damage occurs. An electron ic device exposed to ele ctrostatic discharge (ESD) ma y no t appear to be affected at [...]

Removing DIPs* from vinyl tray Removing DIPs* from Styrofoam Removing bubble pack from PCB Packing PCBs in foam-lined box 2,000 V 3,500 V 7,000 V 5,000 V 4,000 V 5,000 V 20,000 V 11,000 V 11,500 V 14,500 V 26,500 V 21,000 V *These are then multi-packaged inside plastic tubes, trays, or Styrofoam. NOTE: 700 volts can degrade a product. Preventing El[...]

Grounding the Work Area To prevent static damage at the work area, use the following precau tions: ● Cover the work surface with approved static-dissi pa tive material. Provide a wrist strap connected to the work su rface and properly ground ed tools and equipment. ● Use static-dissipative mats, fo ot straps, or air ionizers to give ad ded prot[...]

Operating Guidelines To prevent overhea ting and to help prolong the life of the comp uter: ● Keep the computer away from excessive moisture, direct sunlig ht, and extremes of heat and cold. ● Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides of the co mputer and ab ove the monito r to permi[...]

To clean the comput er case, follow the procedures described below: ● To remove light stains or dirt, use plain water with a clean, lin t-free cloth or swab. ● For stronger stains, use a mild d ishwashing liquid diluted with water. Rinse well by wiping it with a cloth or swab dampened with cle ar water. ● For stubborn stains, use isopropyl (r[...]

Cleaning the Mouse Before cleanin g the mouse, ensure that the power to the computer is turned off. ● Clean the mouse ball by first removing the retaining plate and the ball from the ho using. Pull out any debris from the b all socket and wipe the ba ll with a clean, dry cloth be fore reassembly. ● To clean the mou se body, follow the p rocedur[...]

Cables and Connectors Most cables used throug hout the unit are flat, flexible cables. These cables must be handled with ca re to avoid damage . Apply only the ten sion required to seat or unseat the cables during insertion or remova l from the connecto r. Handle cables by the co nnector whenever po ssible. In all cases, avoid ben ding or twisting [...]

8 Removal and Replacement Procedures Microtower (MT) Chassis Adherence to the p rocedures and pr ecautions described in this chapter is essential for proper service . After completing all necessary re moval and replacement procedures, run the Diagnostics utility to verify that all components operate prop erly. NOTE: Not all features listed in this [...]

Preparation for Disassembly See Identifying the Chassis, Routine Care, and Disa ssembly Preparation on page 65 for initial safety procedures. 1. Remove/disengage a ny security devices that prohibit opening the computer ( External Security Devices on page 116 ). 2. Close any open software applications. 3. Exit the operating system. 4. Remove any dis[...]

Access Panel 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 74 ). CAUTION: Be fore removing the co mputer access panel, ensure that th e computer is turned off and that the power cord i s discon nected from the electrical ou tlet. 2. Loosen the two captive thu mbscrews (1) that secure the access panel to the compu[...]

Front Bezel 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 74 ). 2. Remove the computer access panel. 3. Lift up the three ta bs on the side of the bezel (1) , then rotate th e bezel off the chassis (2) . Figure 8-3 Removing the Front Bezel To reinstall the fron t bezel, reverse the remo val procedure. 76 Chapter 8 [...]

Removing Bezel Blanks On some models, there are bezel bl anks covering the 3.5-inch an d 5.25-inch external drive bays tha t need to be removed befo re installing a drive. To remove a bezel blank: 1. Remove the access pan el and front bezel. 2. To remove a bezel blank, push the two retaini ng tabs that hol d the bezel blank in pla ce towards the ou[...]

Cable Management Always follow good cable management practice s when working inside the computer. ● Keep cables away fro m major heat sources like the heat sink. ● Do not jam ca bles on top of exp ansion cards or memory modules. Printed ci rcuit card s like these are not designed to take excessive pressure on them. ● Keep cables clear of sl i[...]

Cable Connections System board connectors are colo r-coded to make it ea sier to fin d the proper c onnectio n. Connector Na me Connector Color Description PWR, P1 Whit e Power supply, 6-pin PWRCPU, P3 White Power supply, 4-pin PS STAT White Power supply, 6-pin SATS PWR 1 Black Optical drive powe r connector, 4-pin SATS PWR 2 Black Hard drive power[...]

Memory The computer comes wi th double data rate 3 synchronous dynami c random access memory (DDR3- SDRAM) dual inline me mory modules (DIMMs). The memory sockets on the system board can be po pulated with up to four industry- standard DIMMs. These memory sockets are po pulated with at leas t one preinstalle d DIMM. To achieve the maximum memory su[...]

Figure 8 -5 DIMM Socket Locations Table 8-1 D IMM Socket Loca tions Item Description Socket Color 1 XMM1 socket, Channel A (populate fourth) White 2 XMM2 socket, Channel B (populate third) White 3 XMM3 socket, Channel A (populate seco nd) Black 4 XMM4 socket, Channel B (populate first) Black NOTE: A DIMM must occupy the black XMM4 sock et. Otherwis[...]

3. Open both latche s of the memory module socket (1) , and insert the m emory module into the socket (2) . Figure 8-6 Installing a DIMM NOTE: A memory module ca n be installed in only o ne way. Match the notch on the module with the tab on th e memory socket. A DIMM must occupy the XMM4 socket. Always populate XMM4 before XMM2, and XMM3 before XMM[...]

Expansion Cards The computer has one PCI expansion slot, two PCI Express x1 expansion slots, and one PCI Express x16 expansion slot. Figure 8 -7 Expansion Slot Locations Table 8-2 Expansio n Slot Locations Item Description 1 PCI expansion slot 2 PCI Express x16 expansion slot 3 PCI Express x1 expansion slot 4 PCI Express x1 expansion slot NOTE: You[...]

4. Release the slot cover retention latch that se cure s the PCI slo t covers by lifting the green tab on the latch and ro tating the l atch to the open po sition. Figure 8-8 Openi ng the Expansion Sl ot Retainer 5. Before installing an expansion card, remove the expansion slot cover or the existing expansion card. NOTE: Before removing an installe[...]

b. If you are removin g a standard PCI card or PC I Expre ss x1 card, hold the ca rd at each end, and carefully rock it b ack and forth until th e connectors pul l free from the socke t. Pull the expansion card straight up from the socket then aw ay from the inside of the chassis to release it from th e chassis frame. B e sure not to scrape the car[...]

7. If you are not install ing a new expansion card , in stall an expansion slo t cover to close the op en slot. CAUTION : After removing an ex pansion card, you must replac e it with a new card or expa nsion slot cover for prop er cooling of in ternal compone nts during operation. 8. To install a new expansion card, hold the card just above the exp[...]

10. Connect external cables to th e installed card, if neede d. Connect intern al cables to the sys tem board, if needed. 11. Reconfigure the computer, if nece ssary. Refer to the Computer Setup (F10) Utility Guide for instructions on using Co mputer Setup. Drive Positions Figure 8 -14 Drive Positions 1 Two 5.25-inch external drive bays for op tion[...]

Installing and Removing Drives When installing additional driv es, follow these guidelines: ● The primary Serial ATA (SATA) h ard drive must be co nnected to the da rk blue primary SATA connector on the system board labeled SATA0 . ● Connect a SATA optical drive to the white SATA connector on the system board labeled SATA1. ● Connect devices [...]

CAUTION: To prevent loss of wo rk and da mag e to the computer or drive: If you are inserting or removing a drive, shut down the operat ing system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the compu ter is on or in standby mo de. Before handl ing a drive, ensure that you are disch arged of static electr[...]

System Board Drive Connections Refer to the following illustrati on and table to identify the system board drive connectors. Figure 8-16 System Board Drive Connection s Table 8- 3 System Board Dri ve Connections No. System Board Connector System Board Label Co lor 1 SATA3 SATA3 orange 2 SATA2 SATA2 light blue 3 SATA1 SATA1 white 4 SATA0 SATA0 dark [...]

Removing an External 5.25- inch or 3.5-inch Drive CAUTION: All removable media should be taken out of a drive before removin g the drive from the computer. 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 74 ). 2. Remove the access pan el ( Access Panel on page 75 ). WARNING ! To reduce risk of personal injury from [...]

b. If you are removing a media ca rd reader, disconnect the U SB cable from the system board. If the media card reade r has a 1394 port, di sconnect the 139 4 cable from the PCI card. Figure 8 -18 Disconnecting th e Media Card Reader USB Cable Figure 8 -19 Disconne cting the Medi a Card Reader 13 94 Cable 92 Chapter 8 Removal and Replacement Proced[...]

5. A latch drive bracke t with release tabs secures the drives in th e drive bay. Lift the re lease tab on the latch drive bracket (1) for the drive you want to remove, then slide the drive from its drive bay (2) . Figure 8-20 Removing the External Drives 6. Remove the four guide screws (two on each side) from the old drive. Yo u will need these sc[...]

Installing an Exte rnal 5.25-inch or 3.5-inch Drive NOTE: The system does not support Para llel ATA (PATA) optical drives. 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 74 ). 2. Remove the access panel ( Access Panel on page 75 ). WARNING! To reduce risk of personal injury from hot surfaces, allow the internal syst[...]

6. Slide the drive into the drive bay, making sure to alig n the guide screws with th e guide slots, until the drive snaps into pl ace. Figure 8-22 Sliding the External Dr ives into the Drive Cage 7. Connect the power and data cables to the drive as indicated in the following illustrations. a. If you are installing an optical drive, connect the pow[...]

b. If you are installing a media card reader, connect the USB cable to the system board. If the media card read er has a 1394 port, conn ect the 1394 cable to the PCI ca rd. Figure 8 -24 Connecting the Media Card Reader USB Ca ble Figure 8 -25 Connecting the Media Card Reader 13 94 Cable 8. If installing a new drive, connect the opposit e end of th[...]

Removing an Internal 3.5-inch Hard Drive NOTE: Before you remove the old hard drive, be sure to back up the data fro m the old hard drive so that you can tran sfer the data to th e new hard drive. 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 74 ). 2. Remove the access pan el ( Access Panel on page 75 ). WARNING [...]

Installing an Internal 3.5-inch Hard Drive NOTE: The system does not support Para llel ATA (PATA) hard drives. 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 74 ). 2. Remove the access panel ( Access Panel on page 75 ). WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system component[...]

5. Connect the p ower cable (1) and data cable (2) to the back of the hard drive. Figure 8-30 Connectin g the Hard Drive Cables CAUTION: Never crease or bend a SAT A data cable tighter than a 30 mm (1.18 in) radius. A sharp bend can b reak the internal wires. 6. If installing a new drive, connect the opposite end of the data cabl e to the appropri [...]

2. Remove the screw from th e rear of the carrier (1) and sl ide the top cover off the carrier (2) . Figure 8-31 Removi ng the Carrier Cover 3. Remove the adhesive str ip that secures the thermal sensor to the top of the hard drive (1) and move the thermal se nsor away from the carrier (2) . Figure 8-32 Remo ving the The rmal Sensor 100 Chapter 8 R[...]

4. Remove the four screws from the b ottom of the har d drive carrier. Figure 8-33 Remov ing the Securi ty Screws 5. Slide the hard drive back to discon nect it from the carr ier then l ift it up a nd out of t he carrier . Figure 8-34 Remo ving the Hard Drive Installing and Removing Drives 101[...]

6. Place the new hard d rive in the carrie r then slid e the hard drive back so that it seats in the SATA connector on the carrier's ci rcuit board. Be su re t he connector on the hard drive is pressed all the way into the conne ctor on the carrier's circuit bo ard. Figure 8-35 Replacing the Hard Drive 7. Replace the four screws in th e b[...]

8. Place the thermal sensor on top of the hard dr ive in a position that does not cover the label (1) and attach the thermal sensor to the top of the hard driv e with the adhesive st rip (2) . Figure 8-37 Replacing the Ther mal Sensor 9. Slide the cover on the carrier (1) and replace the screw on the rea r of the carrier to secur e the cover in pla[...]

Fan/Baffle Assembly 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 74 ). 2. Remove the access panel ( Access Panel on page 75 ). 3. Unplug the fa n cable from the system b oard (CHFAN1, P9). 4. Press the lever that secures the assembly to the chassis (1) , pivot the assembly forward t oward the front of the com pute[...]

Front I/O Assembly 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 74 ). 2. Remove the computer acce ss panel ( Access Panel on pag e 75 ). 3. Remove the front bezel ( F ront Bezel on page 76 ). 4. Remove the cables from the clip on top of the ba ffle. 5. Disconnect the three front I/O cables (yellow, gr een, and b[...]

Power Switch/LED Assembly 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 74 ). 2. Remove the access panel ( Access Panel on page 75 ). 3. Remove the front bezel ( Fron t Bezel on page 76 ). 4. Disconnect the cable from the system board (P5, PB/LED). 5. With the co mputer on its side, pr ess on the bottom of the asse[...]

Heat sink WARNING! To reduce risk of personal in jury from hot surfaces, allow the internal system comp onents to cool before touching. 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 74 ). 2. Remove the computer acce ss panel ( Access Panel on pag e 75 ). 3. Loosen the four silver T15 captive screws that secure th[...]

Processor 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 74 ). 2. Remove the access panel ( Access Panel on page 75 ). 3. Remove the heat sink ( Heat sink on page 10 7 ). 4. Rotate the locking le ver to i ts full open position (1) . 5. Carefully li ft the pr ocessor from the soc ket (2) . CAUTION : Do NOT handle th [...]

CAUTION: h eat sink retaining screws should be ti ghtened in diagonally opp osite pairs (as in an X) to evenly seat the h eat sink on the processor. This is especially important as the pins on the socket are very fragile and any damage to them may require replacing the system board. NOTE: After installing a new processo r onto the system boa rd, al[...]

Rear Chassis Fan 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 74 ). 2. Remove the access panel ( Access Panel on page 75 ). 3. Disconnect the fan control cable from the system board ( CHFAN2). 4. Remove the four silver Phillips screws that secure the fa n to the chassis. 5. Lift the fan out of the chassis. To inst[...]

Power Supply 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 74 ). 2. Remove the access pan el ( Access Panel on page 75 ). 3. Disconnect all power cables from the drives and from the system board. 4. Remove the four si lver T15 screws that connect the power supply to the chassis. 5. Press the tab on the ba se pan [...]

System Board 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 74 ). 2. Remove the access panel ( Access Panel on page 75 ). 3. Remove all expansion boards ( Expansion Cards on page 83 ). 4. Disconnect all cables connected to the system bo ard, noting their location for reinstallation. 5. Remove the heat sink ( Heat si[...]

Battery The battery that comes with the computer provid es power to the real-ti me clock. When replacing the battery, use a b attery equivalen t to the battery orig i nally installed in the computer. The computer comes with a 3-volt lithium coin cell battery. WARNING! The comput er contains an intern al lithium manganese di oxide battery. Ther e is[...]

Type 1 Battery Holder 1. Lift the battery out of its holder. 2. Slide the replacem ent battery into p osition, positive side up. 3. The battery hol der automatically secu res the battery in the proper position. 4. Replace the computer access pan el. 5. Plug in the comp uter and turn on power to the computer. 6. Reset the date and time and any speci[...]

4. Plug in the comput er and turn on power to th e computer. 5. Reset the date and time and any special system setups usin g Computer Setup. Refer to the Computer Setup (F10) Utility Guide . Type 3 Battery Holder 1. Pull back on the clip (1) th at holds the battery in place, then remove the battery (2). 2. Insert the n ew battery and position the c[...]

External Security Devices The following secu rity devices are used to preven t unauthori zed access to the internal comp onents of the computer and/or se cure the computer to a fixed obj ect. Cable Lock Figure 8-39 Installing a Cable Lock Padlock Figure 8-40 Installing a Padlock 116 Chapter 8 Removal and Replacement Proced ures Microtower (MT) Chas[...]

HP Business PC Security Lock 1. Fasten the security cable by loop ing it around a stationary object. Figure 8-41 Securing the Cable to a Fixed Obje ct 2. Thread the keyboa rd and mouse cables thro ugh the lock. Figure 8-42 Thre ading the Ke yboard and Mouse Cables External Security Devices 117[...]

3. Screw the lock to the chassis using the screw prov ided. Figure 8-43 Attaching the Lock to the Chassis 4. Insert the plug en d of the security cable into the lock (1) and push the button in (2 ) to engage the lock. Use the key provided to disengage the lock. Figure 8-44 Eng aging the Lock Front Bezel Security The front bezel can be locked in pl [...]

4. Remove the security screw from the inside of the front bezel. Figure 8-45 Retr ieving the Front Bez el Security Sc rew 5. Replace the front bezel. 6. Install the screw through the interi or of the front of the chassis into the front beze l. The screw hole is located toward th e middle of the right edge of the chassis between the hard drive bay a[...]

9 Removal and Replacement Procedures Small Form Factor (SFF) Chassis Adherence to the procedures and precautions d escribed in this c hap ter is essential for proper servi ce. After completing all nece ssary removal and replacem ent procedures, run the Di agnostics utility to verify that all components op erate properly. NOTE: Not all features list[...]

Access Panel 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 120 ). 2. Lift up on the a ccess panel handle (1) then lift the access panel off the computer (2) . Figure 9-1 Removing the Acce ss Panel To install the access panel, reverse the removal procedure. Access Panel 121[...]

Front Bezel 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 120 ). 2. Remove the access panel ( Access Panel on page 121 ). 3. Lift up the three ta bs on the side of the bezel (1) , then rotate th e bezel off the chassis (2) . Figure 9-2 Removing the Front Bezel To install the front bezel, reverse the removal procedu[...]

Bezel Blanks On some models, there are bezel bl anks covering the 3.5-inch an d 5.25-inch external drive bays tha t need to be removed befo re installing a drive. To remove a bezel blank: 1. Remove the access pan el ( Access Panel on page 121 ). 2. Remove the front bezel ( F ront Bezel on page 122 ). . 3. To remove a bezel blank, push the two retai[...]

Installing Additional Memory The computer comes wi th double data rate 3 synchronous dynami c random access memory (DDR3- SDRAM) dual inline me mory modules (DIMMs). DIMMs The memory sockets on the system board can be po pulated with up to four industry- standard DIMMs. These memory sockets are po pulated with at leas t one preinstalle d DIMM. To a[...]

Populating DIMM Sockets There are four DIMM sockets on the system board, with t wo sockets per channel. The sockets are labeled XMM1, XMM2, XMM3, and XMM4. Sockets XMM1 and XMM3 operat e in memory channel A. Sockets XMM2 and XMM4 op erate in memory channel B. Figure 9 -4 DIMM Socket Locations Table 9-1 D IMM Socket Loca tions Item Description Socke[...]

1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 120 ). 2. Remove the access panel ( Access Panel on page 121 ). 3. Rotate up the e xternal drive bay housing to acc ess the memory module soc kets on the system board. Figure 9-5 Rotati ng the Drive Cage Up 126 Chapter 9 Removal and Replacement Proc ed ures Small Form F[...]

4. Open both latches of the memory module so cket (1) , and insert the memory mo dule into the socket (2) . Figure 9-6 Instal ling a DIMM NOTE: A memory module can be installed in only one way. Match the notch on the modu le with the tab on th e memory socket. A DIMM must occupy the black DIMM1 socket. Populate the DIMM sockets in the followi ng or[...]

Expansion Cards The computer has one PCI expansion slot, two PCI Express x1 expansio n slots, and one PCI Express x16 expansion slot. NOTE: The PCI and PCI Express slots su pport only low profile card s. Figure 9-7 Expansion Slot Lo cations Table 9- 2 Expansion Slot Loc ations Item Description 1 PCI expansion slot 2 PCI Express x16 expansion slot 3[...]

4. Release the sl ot cover retention latch that secu re s the PCI slot covers by lifting the green tab on the latch and ro tating the la tch to the open position. Figure 9-8 Opening th e Expansion Slot Retainer 5. Before installing an expansion ca rd, remove the expans ion slot cover or th e existing expansion card. a. If you are installing an expa[...]

b. If you are removi ng a standard PCI card or PCI Exp ress x1 card, hol d the card at each end, and carefully rock it back and forth un til the connectors pu ll free from the socke t. Pull the expansion card straight up from the socket then away from the inside of the chassis to relea se it from the chassis frame. Be sure not to scrape the card ag[...]

6. Store the removed card in a nti-static packaging. 7. If you are not installing a new expansion card, install an expansion slot co ver to close the open slot. CAUTION: After removin g an expansion card , you must replace it with a ne w card or expansion slot cover fo r proper cooling o f internal compon ents during op eration. 8. To install a new[...]

9. Rotate the slot cover retention latch ba ck in place to secure the expansion card. Figure 9-13 Closing the Expansion Slot Retainer 10. Connect external cables to the installed card, if needed. Connec t internal cables to the system board, if needed. 11. Reconfigure the computer, if nec essary. Re fer to the Computer Setup (F 10) Utility Guide fo[...]

Cable Management The Small Form Factor chassis is a very compact computer and proper routin g of the internal cables is critical to the operation of the com puter. Follow good ca ble management practices wh en working inside the computer. ● Keep cables away from major heat sources like the heat sink. ● Do not jam cables on top of expansion card[...]

Cable Connections System board connec tors are color-coded to make it easier to find th e proper connect ion. Connector Name Connecto r Color Description PWR, P1 Whit e Power supply, 6-pin PWRCPU, P3 White Power supply, 4-pin PS STAT White Power supply, 6-pin SATS PWR 1 Black Optical drive power co nnector, 4-p in SATS PWR 2 Black Hard d rive power[...]

Drive Positions Figure 9 -15 Drive Positions Table 9-3 Drive Positi ons 1 3.5-inch internal hard drive bay 2 3.5-inch external drive bay for opti onal drives (media ca rd reader shown) 3 5.25-inch external drive bay for op tional drives (optica l drive shown) NOTE: The drive configuration on your com puter may be different than the drive configurat[...]

Installing and Removing Drives When installing additional driv es, follow these guidelines: ● The primary Serial ATA (SATA) h ard drive must be co nnected to the da rk blue primary SATA connector on the system board labeled SATA0 . ● Connect a SATA optical drive to the white SATA connector on the system board labeled SATA1. ● Connect devices [...]

CAUTION: To prevent loss of wo rk and da mag e to the computer or drive: If you are inserting or removing a drive, shut down the operat ing system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the compu ter is on or in standby mo de. Before handl ing a drive, ensure that you are disch arged of static electr[...]

System Board Drive Connections Refer to the following illustrati on and table to identify the system board drive connectors. Figure 9-17 System Board Drive Connection s Table 9- 4 System Board Dri ve Connections No. System Board Connector System Board Label Co lor 1 SATA3 SATA3 orange 2 SATA2 SATA2 light blue 3 SATA1 SATA1 white 4 SATA0 SATA0 dark [...]

Removing an External 5.25-inch Drive CAUTION: All removable media should be taken out of a drive before removin g the drive from the computer. To remove a 5.25 -inch external drive: 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 120 ). 2. Remove the access pan el ( Access Panel on page 121 ). 3. Rotate the drive c[...]

5. Rotate the drive ca ge back down to its normal position . CAUTION : Be careful not to pinch any cables or wires when rotating the drive cage down. Figure 9-20 Rotating the Drive Cage Down 6. Press down on the green drive retainer button loca ted on the left side of the drive to disengage the drive from the drive cage (1) . While pressing the dri[...]

4. Install fou r M3 metric gu ide screws in the lower holes on each side of the drive. HP has provided four extra M3 metric guide screws on the fron t of the chassis, under the front bezel. T he M3 metric guide screws are black. Refer to Installing and Re moving Drives on pa ge 136 for an illustration of the extra M3 metric guide s crews locati on.[...]

6. Rotate the drive ca ge to its upright position. Figure 9-24 Rotating the Drive Cage Up 7. Connect the SATA data cable to the whit e system board connector labeled SATA1. 8. Route the data cable through the cable guide s. CAUTION : There are two cable guid es that keep the data cab le from being pi nched by the drive cage when raising or lowering[...]

10. Rotate the drive cage back d own to its normal position. CAUTION: Be careful not to pinch any cables or wires when rot ating the driv e cage down. Figure 9-26 Rotat ing the Drive Cage Down 11. Replace the access panel. The system automatically recognizes th e drive and re config ures the computer. Removing an External 3.5-inch Drive CAUTION: Al[...]

2. Disconnect the drive cables from the rea r of the dr ive, or, if you are removing a media card reader, disconnect the USB and 1394 cables from th e system board as indicated in the following illustrations. NOTE: On some models, the media card reader doe s not include a 1394 port or cable. Figure 9-27 Disconnecting the Media Card Reader USB Ca bl[...]

3. Press down on the green drive retainer button locate d on the left side of th e drive to d isengage th e drive from the drive cage (1) . While pressing the drive retainer button, sli de the drive back unti l it stops, then lift it up and out of the drive cage (2) . Figure 9-29 Removing a 3.5-inch Drive (Me dia Card Reader Shown) NOTE: To replace[...]

3. Position the guide screws on the drive into the J- slots in the drive bay. Th en slide the drive toward the front of the computer unti l it locks into place. Figure 9-30 Installi ng a Drive into the 3.5-inch Dr ive Bay (Media Card Reader Sh own) 4. Connect the appropriat e drive cables: a. If installing a second ha rd drive, connect th e power a[...]

Removing and Replacing th e Primary 3.5-inch Inte rnal SATA Hard Drive NOTE: The system does not support Para llel ATA (PATA) hard drives. Before you remove the old hard dr ive, be sure to ba ck up th e data from the old h ard drive so that you can transfer the data to the new hard d rive. The preinstalled 3 .5-inch hard drive is located unde r the[...]

4. Rotate the power su pply to its upright position. T he hard drive is located beneath the power supply. Figure 9-32 Raising the Power Supply 5. Disconnect the power cable (1) and data cable (2) from the back of the hard drive. Figure 9-33 Disconnecting the Hard Drive Power Ca ble and Data Cable 148 Chapter 9 Removal and Replacement Proc ed ures S[...]

6. Press down on th e green release l atch next to the hard drive (1) . While holding the latch down , slide the drive forward until it stops, t hen lift the drive up and ou t of the bay (2) . Figure 9-34 Remo ving the Hard Drive 7. To install a hard drive, you must transfer the s ilver and blue isolation mounting guide screws from the old hard dri[...]

8. Align the guide screws with the slots on the chassis drive cage, press the har d drive down into the bay, then slide it back unt il it stops and locks in place. Figure 9-36 Installi ng the Hard Drive 9. Connect the p ower and data cables to the back of the hard drive. NOTE: When replacing the primary hard drive, be sure to route the SAT A and po[...]

Removing and Replacing a Removable 3.5-inch SATA Hard Drive Some models are equip ped with a removable SATA Hard Drive Enclosu re in the 5.25-inch extern al drive bay. The hard drive is housed in a carrier that can be qu ickly and easily removed from the drive bay. To remove and repla ce a drive in the carrier: NOTE: Before you remove the old hard [...]

4. Remove the four scre ws from the bottom of the hard dri ve carrier. Figure 9-39 Re moving the S ecurity Screws 5. Slide the hard drive back to disconnect it from the carrier then lift it up and out of the carrier. Figure 9-40 Removing the Hard Drive 152 Chapter 9 Removal and Replacement Proc ed ures Small Form Factor (SFF) Chassis[...]

6. Place the new hard drive in the carrier then slide the hard drive back so th at it seats in the SATA connector on the carrier's circu it board. Be sure the connector on the hard driv e is pressed all the way into the connector on the carrier's circuit board. Figure 9-41 Replacin g the Hard Drive 7. Replace the four screws in th e botto[...]

8. Place the thermal sen sor on top of the h ard dr ive in a position that does not cover the la bel (1) and attach the thermal sensor to the top of the h ard drive with the adhesive stri p (2) . Figure 9-43 Repl acing the Thermal Sensor 9. Slide the cover on the carrier (1) and replace the screw on the rear of the carrier to secure the cover in pl[...]

Baffle 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 120 ). 2. Remove the access pan el ( Access Panel on page 121 ). 3. Remove the cable from the arm that e xtends from the side of the baffle (1) . 4. Lift the baffle st raight up out of t he chassis (2) . Figure 9-45 Removing the baffle To install the baf fle, r[...]

Front Fan Assembly 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 120 ). 2. Remove the access panel ( Access Panel on page 121 ). 3. Remove the front bezel ( Fron t Bezel on page 122 ). 4. Remove the baffle ( Baffle on page 155 ). 5. Disconnect the fan cable from the system board (CH FAN1, P9). 6. On the front of th[...]

Front I/O/Power Switch Assembly 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 120 ). 2. Remove the access pan el ( Access Panel on page 121 ). 3. Remove the front bezel ( F ront Bezel on page 122 ). 4. Remove the front fan assembly ( Front Fan Assembly on page 156 ). 5. Remove the black T15 screw (1) that secures[...]

8. While holding the body of the a ssemb ly, pull the assembly away from th e front of the co mputer while guiding the cables through the hole in the drive cage (3) . Figure 9-49 Guid ing the wires through the drive cage 9. Remove th e assembly from the c hassis. To reinstall the fron t I/O/power supply assembly, reverse the removal proc edure. 158[...]

Speaker 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 120 ). 2. Remove the access pan el ( Access Panel on page 121 ). 3. Remove the front bezel ( F ront Bezel on page 122 ). 4. Rotate the drive cage to its upright po sition. 5. Disconnect the sp eaker wire from the syst em board (SPRK, P5). 6. Remove the two scr[...]

Heat sink 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 120 ). 2. Remove the access panel ( Access Panel on page 121 ). 3. Remove the baffle ( Baffle on page 155 ). 4. Remove the fron t fan assembly ( Front Fan As sembly on page 15 6 ). 5. Loosen the four captive screws that secure the heat sink to the system board[...]

Processor 1. Prepare the comp uter for disassemb ly ( Preparat ion for Disas sembly on page 120 ). 2. Remove the access pan el ( Access Panel on page 121 ). 3. Remove the fan shroud ( Baffle on page 155 ). 4. Remove the heat sink ( Heat si nk on page 160 ). 5. Rotate the locking le ver to its full open positio n (1) . 6. Carefully lift the processo[...]

4. Apply the thermal gre ase provided in the sp ares kit to the top of the processor and install the heat sink atop the processor. 5. Go to step 7. 6. If using a new heat sin k, remove the p rotective coveri ng from the bottom of the heat sink and place it in position atop the proc essor. 7. Secure the heat sink to the syst em boar d and system boa[...]

6. Rotate the power supply to its full upright positio n (1) , pull the power supply forwa rd (2) until the posts on the power suppl y move forward in the power supply bracke t (3) , and then lift the power supply straight u p and out of the cha ssis. Figure 9-53 Removing the power supply To install the po wer supply, reverse the removal proce dure[...]

System Board 1. Prepare the co mputer for dis assembly ( Preparation for Disassembly on page 120 ). 2. Remove the access panel ( Access Panel on page 121 ). 3. Remove all PCI and PCI Express expan sion boards ( Expansion Cards on page 128 ). 4. Remove the baffle from the chassis ( Baffle on page 155 ). 5. Remove the fan from the chassis ( Front Fan[...]

CAUTION: Before reinstalling the h eat sink you must clean the top of the pro cessor and the bottom of the heat sink with an alcohol pad suppli ed in the spares kit. After the alcohol has ev aporated, apply thermal grease to the top of the p rocessor from the syringe supplied in the spares kit. CAUTION: When reconnecting the cables it is important [...]

Type 1 Battery Holder 1. Lift the battery out of its holder. Figure 9-55 Removing the batte ry from a type 1 holder 2. Slide the replacem ent battery into p osition, positive side up. 3. The battery hol der automatically secu res the battery in the proper position. 4. Replace the computer access pan el. 5. Plug in the comp uter and turn on power to[...]

4. Plug in the comput er and turn on power to th e computer. 5. Reset the date and time, your passwords, and any special system setups, using Computer Setup. Refer to the Computer Setup (F 10) Utility Guide . Type 3 Battery Holder 1. Pull back on the clip (1) that holds the b attery in place, then remove the battery (2) . 2. Insert the n ew battery[...]

External Security Devices The following secu rity devices are used to preven t unauthori zed access to the internal comp onents of the computer and/or se cure the computer to a fixed obj ect. NOTE: For inform ation on da ta securit y feature s, refer to the Computer Setup (F10) Utility Guide , the Desktop Mana gement Guide , and the HP ProtectTools[...]

Padloc k Figure 9 -59 Installing a Padlock HP Business PC Security Lock 1. Fasten the security cable by loop ing it around a stationary object. Figure 9-60 Securing the Cable to a Fixed Obje ct External Security Devices 169[...]

2. Thread the ke yboard and mouse cab les through the lock. Figure 9-61 Thread ing the Keyboard and Mou se Cables 3. Screw the lock to the chassis using the screw prov ided. Figure 9-62 Attaching the Lock to the Chassis 170 Chapter 9 Removal and Replacement Proc ed ures Small Form Factor (SFF) Chassis[...]

4. Insert the pl ug end of the secu rity cable into the loc k (1) and push the button in (2) to engag e the lock. Use the key provid ed to diseng age the lock. Figure 9-63 Engaging the Lock Front Bezel Security The front bezel can be locked in place by insta lling a security screw provid ed by HP. To install the security screw: 1. Prepare the comp [...]

6. Install the security screw ne xt to the middle front bezel release tab to se cure the front bezel in place. Figure 9-65 Installi ng the Front Beze l Security Screw 7. Replace the access pa nel. 172 Chapter 9 Removal and Replacement Proc ed ures Small Form Factor (SFF) Chassis[...]

Using the Small Form Fact or Computer in a Tower Orientation The Small Form Factor com puter can be used in a tower orientation with an optional tower stand that can be purcha sed from HP. 1. Remove/disengage any secu rity de vices that prohibit opening the compute r. 2. Remove all removable media, su ch as compact discs or USB flash drives, from t[...]

A Connector Pin Assignments This appendix conta ins the pin assignm ents for ma ny computer and wo rkstat ion conn ectors. Some of these connectors may not be used on the prod uct being serviced. Keyboard Connector and Icon Pin Signal 1 2 3 Data Unused Ground 4 5 6 +5 VDC Clock Unused Mouse Connector and Icon Pin Signal 1 2 3 Data Unused Ground 4 5[...]

Ethernet RJ-45 Connector a nd Icon Pin Signal 1 2 3 4 (+) Transmit Data (-) Transmit Da ta (+) Receive Data Unused 5 6 7 8 Unused (-) Receive D ata Unused Unused Serial Interface, Po wered and Non-Powered Connector a nd Icon Pin Signal 1 2 3 Carrier Detect (12V if powere d) Receive Data Transmit Data 4 5 6 Data Terminal Ready Signal Ground Data Set[...]

Microphone Connector and Icon (1 /8” miniphone) Pin Signal 1 2 3 1 (Tip) 2 (Ring) 3 (Shield) Audio_left Audio_Right Ground Headphone Connector and Icon (1 /8” miniphone) Pin Signal 1 2 3 1 (Tip) 2 (Ring) 3 (Shield) Audio_left Power_Right Ground Line-in Audio Connector and Icon (1 /8” miniphone) Pin Signal 1 2 3 1 (Tip) 2 (Ring) 3 (Shield) Aud[...]

Monitor Connector a nd Icon Pin Signal Pin Signal 1 2 3 4 Red Analog Green Analog Blue Analog Not used 9 10 11 12 +5V (fused) Ground Not used DDC Serial Data 5 6 7 8 Ground Ground Ground Ground 13 14 15 Horizontal Sync Vertical Sync DDC Serial Clock 4-Pin Power (for CPU) Connector a nd Icon Pin Signal 1 2 3 4 GND GND +12V CPU -12V CPU Monitor 177[...]

SATA Data and Power Drive Connec tor Pin Signal Pin Signal Pin Signal Pin Si gnal S1 S5 Ground B- S2 S6 A+ B+ S3 S7 A- Ground S4 Ground P1 P5 P9 P13 Ground B- V 5 V 12 P2 P6 P10 P14 V 3.3 Ground Ground V12 P3 P7 P11 P15 V 3.3 V 5 Reserved V 12 P4 P8 P12 Ground V 5 Ground *S = Data, P = Power PCI Express x1, x4, x8, and x16 PCI Ex press Connector Pi[...]

51 52 53 54 55 GND PERp8 PERN8 GND GND 56 57 58 59 60 PERp9 PERn9 GND GND PERp10 61 62 63 64 65 PERn10 GND GND PERp11 PERn11 66 67 68 69 70 GND GND PERp12 PERn12 GND 71 72 73 74 75 GND PERp13 PERn13 GND GND 76 77 78 79 80 PERp14 PERn14 GND GND PERp15 81 82 PERn15 GND Pin B information is on the next page NOTE: x1 PCI Express uses pins 1-18 x4 PCI E[...]

26 27 28 29 30 GND PETp3 PETn3 GND RSVD 31 32 33 34 35 PRSNT2# GND PETp4 PETn4 GND 36 37 38 39 40 GND PETp5 PETn5 GND GND 41 42 43 44 45 PETp6 PRTn6 GND GND PETp7 46 47 48 49 50 PETn7 GND PRSNT2# GND PETp8 51 52 53 54 55 PETn8 GND GND PETp9 PETn9 56 57 58 59 60 GND GND PETp10 PETn10 GND 61 62 63 64 65 GND PETp11 PETn11 GND GND 66 67 68 69 70 PETp12[...]

DVI Connector Connector a nd Icon Pin Signal Pin Signal 1 2 3 4 T.M.D.S . Data2 – T.M.D.S . Data2 + T.M.D.S. Data2/4 Shield T.M.D.S . Data4 – 13 14 15 16 T.M.D. S. Data3+ +5V Power Ground (for +5V) Hot Pug Dete ct 5 6 7 8 T.M.D.S . Data4 + DDC Clock DDC Data No Connect 17 18 19 20 T.M.D. S. Data0– T.M.D. S. Data0+ T.M.D.S. Data0/5 Shield T.M.[...]

DisplayPort Connector Connector and Icon Pin Signal Pin Signal 1 2 3 4 ML_Lane 0 (p) Ground ML_Lane 0 (n) ML_Lane 1 (p) 13 14 15 16 CONFIG1 CONFIG2 AUX CH (p) Ground 5 6 7 8 Ground ML_Lane 1 (n) ML_Lane 2 (p) Ground 17 18 19 20 AUX CH (n) Hot Plug Return DP_PWR 9 10 11 12 ML_Lane 2 (n) ML_Lane 3 (p) Ground ML_Lane 3 (n) 182 Appendix A Connector Pin[...]

B Power Cord Set Requirements The power supplies on some computers have extern al power switches. The voltag e select switch feature on the computer permits it to opera te from any line voltage between 100-120 or 220-240 volts AC. Power supplies on th ose computers that do not have ex ternal power switches are equipped wi th internal switches that [...]

Country-Specific Requirements Additional requ irements specific to a countr y are shown in parenth eses and explained below. Country Accrediting Agenc y Coun try Accrediting Agency Australia (1) Austria (1) Belgium (1) Canada (2) EANSW OVE CEBC CSA Italy (1) Japan (3) Norway (1 ) Sweden (1) IMQ METI NEMKO SEMKO Denmark (1) Finland (1) France (1) Ge[...]

C POST Error Messages This appendix lists th e error codes, e rror messages, and the vario us indicator light and audible sequences tha t you may encounter during Power-On Se lf-Test (POST) or computer restart, the proba ble source of the p roblem, and steps you can take to resolv e the error co ndition. POST Message Disabled suppresses most system[...]

POST Numeric Codes and Text Messages This section covers those POST errors that h ave numeric codes associated wi th them. The section also includes some text messa ges that may be encountered during POST. NOTE: The computer will beep once after a POST text mess age is displayed on the screen. Table C -1 Numeric Codes and Text Messag es Control pan[...]

Control panel message Description Recommended action 163-Time & Date Not Set Invalid time or date in configuration memory. RTC (real-time clock) battery may need to be replaced. Reset the date and time under Con trol Panel (Computer Setup can also be used). If the problem persists, replace the RTC battery. See the Hardware Refer ence Guide for [...]

Control panel mes sage Description Recommended ac tion 301-Keyboard Error Keyboard failure. 1. Reconnect keyboard with computer turn ed off. 2. Check connector for bent or missing pins. 3. Ensure that none of the keys ar e depressed. 4. Replace keyboard. 303-Keyboard Controller Error I/O board keyboard controller. 1. Reconnect keyboard with compute[...]

Control panel message Description Recommended action 605-Diskette Drive Type Err or Mismatch in drive type. 1. Disconnect any other diskette controller devices (tape drives). 2. Clear CMOS. (See Appendix B, Password Security and Resetting CMOS on page 235 .) 660-Display cache is detected unreliable I ntegrated graphics controlle r display cache is [...]

Control panel mes sage Description Recommended ac tion 1720-SMART Hard Drive Detects Imminent Failure Hard drive is about to fail. (Some hard drives have a hard drive fir mware patch that will fix an erroneous error messag e.) 1. Determine if hard drive is giving correct error message. Enter Computer Setup and run the Drive Protection System test u[...]

Control panel message Description Recommended action 2202-PMM Deallocation Error during MEBx cleanup Memory error during POST execution of the Management Engine (ME) BIOS Extensions option ROM. 1. Reboot the computer. 2. Unplug the power cord, re-s eat the memory modules, and reboot the computer. 3. If the memory configuration was recently changed,[...]

Control panel mes sage Description Recommended ac tion Network Server Mode Active and No Keyboard Attached Keyboard failure while Networ k Server Mode enabled. 1. Reconnect keyboard with computer turn ed off. 2. Check connector for bent or missing pins. 3. Ensure that none of the keys ar e depressed. 4. Replace keyboard. Parity Check 2 Parity RAM f[...]

Interpreting POST Diagnos tic Front Panel LEDs and Audible Codes This section covers the front p anel LED codes as well as the audibl e codes that may occur before o r during POST that do not necessarily have an error co de or text messag e associated with th em. WARNING! When the computer is plugged into an AC power source, voltage is always app l[...]

Activity Beeps Possible Cause Recommended Ac tion Red Power LED flashes four times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 4 Power failure (power supply is overloaded). 1. Open the hood and ensure the 4 or 6-wire power supply cable is seated into the connector o[...]

Activi ty Beeps Possible Cause Recommended Action Red Power LED flashes nine times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 9 System powers on but is unable to boot. 1. Check that the voltage selector, located on the rear of the power supply (some models), is set[...]

Activity Beeps Possible Cause Recommended Ac tion Red Power LED flashes eleven times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 11 The current processor does not support a feature previously enabled on this system. 1. Install a TXT capable processor. 2. Disable TXT[...]

D Troubleshooting Without Diagnostics This chapter provid es information on how to identify and corr ect minor problems, such a s hard drive, optical drive, graphics, audio , memory, and softwa re p roblems. If you encounter problems with the computer, refer to the tables i n this chapter for probable causes an d recommended solutions. NOTE: For in[...]

● Refer to the comp rehensive online technica l support at http://www.hp.com/ support . ● Refer t o Helpful Hints on page 198 in this guide. To assist you in resolving problems online, HP In stan t Support Professional Edition p rovides you with self-solve diag nostics. If you need to contact HP su pport, use HP Inst ant Support Profes sional E[...]

● Reconfigure the computer after installing a non-plug and play expansion b oard or other option. See Solving Hardware In stallation Problems on page 219 for instructions. ● Be sure that all the ne eded device drivers have been installed. For example, if you are u sing a printer, you need a dri ver for that model printer. ● Remove all bootab [...]

Solving General Problems You may be able to easily resolve the gene ral problem s described in this section. If a problem persists and you are unable to resolve it yourself or if you feel uncomfor table about performing the opera tion, contact an authorized dealer or reseller. WARNING! When the computer is plug ged into an AC power sou rce, voltage[...]

There is no sou nd or sound volum e is too low. Cause Solution System volume may be set low or muted. 1. Check the F10 BIOS settings to make sure the internal system speaker is not muted (this setting does not affect the ext ernal speaker s). 2. Make sure the external sp eakers are properly connected and powered on a nd that the speakers' volu[...]

Poor performance is experienced. Cause Solution Too many applications running. 1. Close unnecessary applications to free up memo ry. 2. Add more memory. Some applications run in the background and can be closed by right-clicking on their corresponding icons in the task tray. To pr event these applications from launching at startup, go to St art >[...]

System does not pow er on and the LEDs on t he front of the comp uter are not flashing. Cause Solution System unable to power on. Press and hold the power button for less than 4 seconds. If the hard drive LED turns green, then: 1. Remove the expansion cards one at a time until the 5V_aux light on the system board turns on. 2. Replace the system boa[...]

Solving Power Problems Common causes and solutions for power prob lems are liste d in the following ta ble. Table D-2 Solving Power Problems Power supply shuts down intermitt ently. Cause Solution Power supply will not turn on because of in ternal power supply fault. Contact an authorized service provider to replace the powe r supply. Computer powe[...]

Solving Hard Drive Problems Table D -3 Solving Hard Drive Problems Hard drive error occurs. Cause Solution Hard disk has bad s ectors or has fai led. 1. In Microsoft Windows XP, right-click St art , click Explore , and select a drive. Select File > Propert ies > Tools . Under Error-checking , click Check No w . In Microsoft Windows Vista, rig[...]

Nonsystem disk/NTLDR miss ing message. Cause Solution The system is trying to start from a media device that is not bootable. Remove the media device from the drive. The system is trying to start from the hard drive but the hard drive may have been damaged. 1. Insert a bootable media device into the drive and restart the computer. 2. Check the hard[...]

Computer seems to be locked up. Cause Solution Program in use has stopped respo nding to commands. Attempt the normal Windows “Shut Down” procedure. If this fails, press the power button for four or more seconds to turn off the power. To restart the computer, press the power button again. The removable hard d rive has no power to th e hard driv[...]

Solving Media Card Reader Problems Table D-4 Solving Me dia Card Re ader Problem s Media card will not w ork in a digital camera after form at ting it in Microsoft Windows XP or Microsoft Windows Vista. Cause Solution By default, Windows XP and Windows Vista will format an y media card with a capacity greater than 32MB with the FAT32 format. Most d[...]

After installing the med ia card reader and booting to Window s, the reader and the inserted cards are not recog nized by the computer. Cause Solution The operating system needs time to recognize the device if the reader was ju st installed into the computer and yo u are turning the PC on for the first time. Wait a few seconds so that the operating[...]

Solving Display Problems If you encounter display problems, se e the documentation that came with the monitor and to the common causes and solutions li sted in the fo llowing table. Table D-5 Solving Disp lay Problems Blank sc reen (n o video ). Cause Solution Monitor is not turned on and the monitor ligh t is not on. Turn on the monitor and check [...]

Cannot enable integrated graphics after installing a PCI Express graph ics card. Cause Solution On systems with Intel integrated graphics, the integrated graphics cannot be enabled after installing a PCI Express x16. The integrated graphics can be enabled in Computer Setup if a PCI or PCI Express x1 graphics card is installed, but it cannot be enab[...]

Dim characters. Cause Solution The brightness and contrast controls a re not set properly. Adjust the monitor brightness and contrast controls. Cables are not properly co nnected. C heck that the graphics cable is securely con nected to the graphics card and the monitor. Blurry video or requested resolution cannot be set. Cause Solution If the grap[...]

“Out of Range” displays on screen. Cause Solution Video resolution and refre sh rate are set higher than what the monitor supports. Restart the computer and enter Safe Mode. Change the settings to a supported setting then restart the computer so that the new settings take effect. Vibrating or rattling noise coming from inside a CRT monitor when[...]

Certain typed s ymbols do not appear co rrect. Cause Solution The font you are using does not support that particu lar symbol. Use the Character Ma p to locate and select the appropria te symbol. Click Start > All Programs > Accessories > System Tools > Character Map . You can copy the symbol fro m the Character Map into a document. Sol[...]

Sound does not co me out of the speake r or headphones. Cause Solution External speakers plugged into the wro ng audio jack on a recently installed sound card. See the sound card documentatio n for proper speaker connection. Digital CD audio is not enabled. Enable digital CD audio. In the Device Manager, right-click on the CD/DVD device and select [...]

Solving Printer Problems If you encounter printer problems, see the documentat ion that came with the printer and to the common causes and solutions li sted in the fo llowing table. Table D-7 Solving Prin ter Problems Printer will not print. Cause Solution Printer is not turned on and online . Turn the printer on and make sure it is online. The cor[...]

Solving Keyboard and Mouse Problems If you encounter keyboa rd or mouse problems, see the documentation that came with the equipment and to the co mmon causes and so lutions listed in the following table. Table D -8 Solving Keyboard Problems Keyboard commands an d typing are not recognized by the compute r. Cause Solution Keyboard connector is not [...]

Mouse does not respond to movement or is too slow. Cause Solution Mouse may need cleaning. Remove the roller ball cover on the mouse and clean the internal components. Mouse may need repair. See the Worldwide Limited Wa rra nty for terms a nd conditions. Computer is in standby mode. Pre ss the power button to resume from standby mode. CAUTION: When[...]

Solving Hardware Installation Problems You may need to reconfigure the compu ter when you add or remove hardware, such as an additio nal drive or expansion card. If you install a plug and play device, Windows auto matically recognizes the device and configures the computer. If you insta ll a non–plug and play device, yo u must reconfigure the com[...]

Power LED flashes Red five times, o nce every second, followed by a two seco nd pause, and the computer beeps five times. (Beeps stop after fifth iteration but LEDs continue fl ashing.) Cause Solution Memory is installed incorrectly or is bad. CAUTION: To avo id damage to the DIMMs or the system board, you must unplug the computer power cord before[...]

Solving Network Problems Some common causes an d solutions for network prob lems are li sted in the following tab le. These guidelines do not discuss th e process of debugging th e network cabling. Table D-11 Solving Network Problems Wake-on-LAN feature is not funct ioning. Cause Solution Wake-on-LAN is not enabled. To enable Wake-on-LAN in Windows[...]

Network status link light never flashes. NOTE: The network status light is suppose d to flash when there is network activity. Cause Solution No active network is detected. Check cabling and network equipment for p roper connection. Network controller is not set up properly. Check for the de vice status wi thin Windows , such as Device Manager for d[...]

Network controller stopped working w hen an expansion board was added to the computer. Cause Solution The network controller requires drivers. Verify that the drivers were n ot accidentally deleted when the drivers for a new expansion board were installed . The expansion board installed is a network card ( NIC) and conflicts with the embedded NIC. [...]

Solving Memory Problems If you encounter memory problems, some common causes and solutions are liste d in the following tab le. CAUTION: Power may s till be supplied to the DIMMs when the comput er is turned of f (depending on the Management Engine (ME) setti ngs on some models). To avoid damage to the DIMMs or the system board, you mu st unplug th[...]

Insufficient memory error during operation. Cause Solution Too many Terminate and Stay R esident programs (TSRs) are installed. Delete any TSRs that you do not need. You have run out of memory for the application. Check the memory requirements for the application or add more memory to the computer. Power LED flashes Red five times, once every secon[...]

Solving Processor Problems If you encounter processor problems, common causes and solutions are listed in the following table. Table D-13 Solving Processor Problems Poor performance is experienced. Cause Solution Processor is hot. 1. Make sure the airflow to the computer is not blocked. 2. Make sure the fans are connected and working properly (some[...]

Solving CD-ROM and DVD Problems If you encounter CD-ROM or DVD problems, see the common causes an d solutions listed in the following ta ble or to the documentatio n that came with the o ptional device. Table D-14 Solving CD-ROM and DVD Problems System will not boot from CD-ROM or DVD drive. Cause Solution The device is attached to a SATA port that[...]

Movie will not play in the DVD drive. Cause Solution Movie may be regionalized for a different country. See the documentation that came with the DVD drive. Decoder software is not installed. Install decoder software. Damaged media. Replace media. Movie rating locked out by parental lock. U se DVD software to remove parental lo ck. Media installed u[...]

Solving USB Flash Drive Problems If you encounter USB flash drive prob lems, common causes and solutions are listed in the fo llowing table. Table D-15 Solving USB Flash Drive Prob lems USB flash drive is not s een as a drive letter in Windows. Cause Solution The drive letter after the last physical drive is not availa ble. Change the default drive[...]

Solving Front Panel Component Problems If you encounter prob lems with devices connected to the fron t panel, refer to the common caus es and solutions listed in the following table. Table D-16 Solving Front Panel Component Pro blems A USB device, headphone, or microphone is not reco gnized by the computer. Cause Solution Device is not properly co [...]

Solving Internet Access Problems If you encounter Internet access proble ms, consult your Internet Serv ice Provider ( ISP) or re fer to the common causes and solutions listed in th e following table. Table D-17 Solving Internet Ac cess Problem s Unable to connect to the Internet. Cause Solution Internet Service Provider (ISP) acco unt is not set u[...]

Internet takes too long to download Web sites. Cause Solution Modem is not set up properly. Verify that the modem is connected and communicating properly. Windows XP 1. Select Start > Control Panel . 2. Double-click System . 3. Click the Hardware tab. 4. In the Device Manager area, click the De vice Manager button. 5. Double-click Modems . 6. Do[...]

Solving Software Problems Most softw are proble ms occur as a result of t he following : ● The application was not instal led or configured correctl y. ● There is insufficient memory av ailable to ru n the application. ● There is a conflict between ap plications. ● Be sure that all the ne eded device drivers have been installed. ● If you [...]

Contacting Customer Support For help and service, contact an au thorized resell er or dealer. To lo cate a reseller or dealer near you, visit http://www .hp.com . NOTE: If you take the computer to an au thorized rese lle r, dealer, or servic e provider for service, remember to provid e the setup and p ower-on passwor ds if they are set. Refer to th[...]

E Password Security and Resetting CMOS This computer supports se curity password features , which can be established through the Computer Setup Utilities menu. This computer supports two security password feat ures that are established through the Co mputer Setup Utilities menu : setup password a nd power-on password. When you e stablish only a set[...]

Resetting the Password Jumper To disable the p ower-on or setup password fe atur es, or to clear the power-on or setup passwords, complete the following steps: 1. Shut down the operating system pr operly, then turn off the comp uter and any external devices, and disconnect the power cord from the power outl et. 2. With the powe r cord disconnected,[...]

Clearing and Resetting the CMOS The computer’s configurat ion memory (CMOS) stores information about the co mputer’s configuration. The CMOS button res ets CMOS but does no t clear the po wer-on and setup pa sswords. Clearing CMOS will clear the Active Manage ment Technology (AMT ) settings in the Management Engine BIOS Extension (MEBx ), inclu[...]

4. Locate, press, and hold the CMOS button in for five seconds. NOTE: Make sure you have disconnected the AC powe r cord from the wall o utlet. The CMOS button will not clear CMOS if the power cord is connected. Figure E-1 CMOS button NOTE: For assistance locating the CMOS button and other system board components, see the Illustrated Parts & Se[...]

F Specifications This chapter provid es specific ations for the microtower and small form factor chassis. Microtower Chassis Table F-1 Specifications Desktop Dimensions Height Width Depth 14.85 in 6.95 in 16.85 in 37.72 cm 17.65 cm 42.80 cm Approximate Weight 23.5 lb 10.66 kg Temperature Range Operating Nonoperating 50° to 95°F -22° to 140°F 10[...]

Power Supply Operating Voltage Range (STD PS) Operating Voltage Range (EPA 87/89/85% @ 20/50 /100% load PS) Rated Voltage Range (STD PS) Rated Voltage Range (EPA 87/89/85% @ 20/50 /100% load PS) Rated Line Frequency 115V 90-264 VAC 90-264 VAC 100-240 VAC 100-240 VAC 50-60 Hz 230V 90-264 VAC 90-264 VAC 100-240 VAC 100-240 VAC 50-60 Hz Power Output 3[...]

Small Form Factor Chassis Table F-2 Specifications Desktop Dimensions (in the desktop position) Height Width Depth 3.95 in 13.3 in 14.9 in 10.0 cm 33.8 cm 37.8 cm Approximate Weight 19 lb 8.6 kg Weight Supported (maximum d istributed load in desktop position) 77 lb 35 kg Temperature Range Operating Nonoperating 50° to 95°F -22° to 140°F 10° to[...]

Rated Input Current (maximum) 1 STD PS EPA 87/89/85% @ 20/50/100% load PS 4A @ 100 VAC 4A @ 100 VAC 2A @ 230 VAC 2A @ 230 VAC 1 This system utilizes an active power factor corrected power suppl y. This allows the system to pass the CE mark requirements for use in the countries of the European Un ion. The active power factor corrected powe r supply [...]

Index Symbols/Numerics 4–pin powe r pin assignments 17 7 A access panel, locked 201 access to computer, controlling 50 Altiris Client Management Suite 39 asset tracking 50 audible code s 193 audio connectors 2, 4, 7, 9 audio problems 214 B battery disposal 72 SFF removal and replacement 165 beep codes 193 BIOS Boot Block Emergency Recovery Mode 4[...]

E electrostati c discharge (ESD) preventing damage 67 Emergency Re covery Mode, Boot Block 44 entering power-on password 55 setup password 55 error codes 185, 193 messages 186 ethernet RJ-45 pin assignmen ts 17 5 expansion car d installing 128 removing 128 slot locations 128 expansion slot cover removing 84, 129 replacing 86, 131 F FailSafe Key, or[...]

MT removal and replacement 80 populating sockets 82 memory problems 224 microphone connector 2, 7 microphone pin assign ments 176 monitor pin assignments 177 monitor connector DisplayPort 4, 9 VGA 4, 9 monitor problems 210 mouse pin assignments 174 mouse cleaning 71 mouse connector 4, 9 mouse proble ms 217 MT access panel removal and replacement 75[...]

Recovery Mode, Boot Block Emergency 44 recovery, software 33 Remote Management Technology 40 Remote ROM Flash 35 remote setup 35 Remote System Installation 35 removable hard drive replacing 99, 151 removal and replacement MT access panel 75 MT fan/air baffle 104 MT front bezel 76 MT front USB panel 105 MT heat sink 107 MT memory 80 MT power supply [...]

HP Syst em Softwar e Manager 36 integration 33 Proactive Change Notification (PCN) 42 problems 233 recovery 33 Remote Managem ent Technology 40 Remote System Installation 35 servicing compu ter 71 updating and manag ement tools 35 Verdiem Surveyor 42 spare part numbe r tamper-resistent wrench 71 Torx T-15 screwdriver 71 speaker MT removal and repla[...]