HP (Hewlett-Packard) QV985AV инструкция обслуживания

HP Compaq Business PC Maintenance and Service Guide Pro 6300 Series Microtower Pro 6300 Series Small Form Factor[...]

© Copyright 2012 Hew lett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft, Windows, and Windows Vista are either trademarks or registered trademar ks of Microsoft Corporation in the U nited States and/or other countries. The only warrantie s for HP products and services are set fort[...]

About This Book WARNING! Text set off in this manner indi cates that failure to follow di rections could result in bodily harm or l oss of life . CAUTION: Text set off in this manner indicates that failure to follo w directions could result in damage to eq uipment or loss of informa tion. NOTE: Text set off in this manner provides important su pple[...]

Table of contents 1 Produc t Feature s ............ ............ .............. ........... ............... ............ ............... ........... ..... ............ ........... .......... 1 Standar d Configu ration Fe atures ........... ............. .............. ............. .............. ............. ............... .. .......... 1 Microt[...]

Computer major components ............... ........... ............... .......... ............... .......... ............... . 25 Cables ............... ............ ............ ............ ............. ............ ............ ........... ............... ...... ........ 27 Misc p arts . .................. .............. ................ .......[...]

6 Removal and Replacement Proced ures Microtower (MT) Chas sis ........... ........ ......... .......... ......... .......... . 54 Prepar ation for Disasse mbly ..... ............ .............. ............. .............. ............ .............. ............. .. ... ........ 54 Computer Access Panel ... .......... .......... ............ ....[...]

System Board Co nnections . ............ .......... ........... ........ ............. ......... .......... .......... ............. ..... ........ 107 Drives . ........... .......... ............. .......... .......... ........... ............ ........... .......... ............. ........ ....... ............ .... 108 Drive Positions .............[...]

Contacting Customer Support ......... .......... ....... ......... .......... ....... ......... ....... .......... ......... ....... ..... ....... 176 9 POST Error Messages ............... ........ ........... ......... ........... ........... ........ ............ ......... .......... ....... .......... ....... 177 POST Nume ric Codes and Text Mes[...]

Appendix D Power C ord Set Require ments .. ............. ......... ............. ............. ......... ............. ........... .... ......... 215 Gener al Requireme nts ... ............. ............ ............. ............ ............ .............. ........... .............. .. ... ........ 215 Japan ese Power Cord Re quirements ........[...]

1 Product Features Standard Configuration Features Features may vary de pending on the mode l. For a complete listing of the hardware an d software installed in the computer , run the diagnostic utility (include d on some comput er models only). Figure 1 -1 Microtower Configuration Figure 1 -2 Small Form Factor C onfiguration Standard Conf iguratio[...]

NOTE: The Small Form Factor compute r can also be used in a tower orie ntation. For more information, see Using the Small Form Factor Compu ter in a Tower Orientation on page 135 in this guide. Microtower (MT) Front Panel Components Drive configuration ma y vary by model. Some models have a b ezel blank covering one or more drive bays. Table 1-1 Fr[...]

Small Form Factor (SFF) Front Panel Components Drive configuration ma y vary by model. Some models have a b ezel blank covering one or more drive bays. Figure 1 -3 Front Panel Componen ts Table 1-2 Fron t Panel Compon ents 1 5.25-inch Optical Drive 5 Microphone/Headphone Connector 2 Dual-State Power Button 6 3.5-inc h Media Card Reader (o ptional) [...]

Microtower (MT) Rear Panel Components Figure 1 -4 Rear Panel Components Table 1-3 Rear Panel Comp onents 1 Power Cord Connector 6 Line-Out Connector for power ed audio devices (green) 2 Line-In Audio Connector (blue) 7 PS/2 Keyboard Connector (purple) 3 PS/2 Mouse Connector (green) 8 VGA Monitor Connector 4 Serial Connector 9 DisplayPort Monitor Co[...]

Small Form Factor (SFF) Rear Panel Components Figure 1 -5 Rear Panel Components 1 RJ-45 Network Connector 7 DisplayPort Monitor Connector 2 Serial Connector 8 VGA Monitor Connector 3 PS/2 Mouse Connector (green) 9 PS/2 Keyboard Connector (purple) 4 Power Cord Connector 10 Line-Out Connector for po wered audio devices (green) 5 USB 2.0 ports (black)[...]

Serial Number Location Each compu ter has a unique serial number and a p roduct ID number that are located o n the top cover of the computer. Keep these numbers av ailabl e for use when contacting customer service for assistance. Figure 1 -6 Microtower Serial Numb er a nd Product ID Locati on Figure 1 -7 Small Form Factor Serial Nu mber and Product[...]

2 Activating and Customizing the Software NOTE: This chapter pr ovides informatio n for both Windows 7 an d Windows 8. Activating and customizing the software in Windows 7 If your computer w as not shipped with a Wind ows® operating system, so me por tions of this documentation do not ap ply. Additional information is av ailable in online he lp af[...]

Downloading Windows 7 updates Microsoft may release updates to the operating system . To help keep the comp uter running optimally, HP recommends checking for the late st updates du ring the initial insta llation and periodical ly throughout the life of the comp uter. 1. To set up your Internet connection, click Start > Internet Explorer and fol[...]

CAUTION: After the activation process ha s begun, DO NOT TURN OFF THE CO MPUTER UNTIL THE PROCESS IS COMPLETE. Turning off the comp uter during the activa tion process may damage the software tha t runs the computer o r prevent its prop er installation. Downloading Windows 8 updates Microsoft may release updates to the operating system . To help ke[...]

3 Computer Setup (F10) Utility Computer Setup (F10) Utilities Use Computer Setup (F10) Utility to do the following: ● Change factory default settings. ● Set the system date and time. ● Set, view, change, or verify the system configurat ion, including settings for processor, graphics, memory, audio, stora ge, communications, and input devices.[...]

● Solve system configura tion errors detect ed but not automa tically fixed during th e Power-On Self- Test (POST). ● Replicate the system setup by saving system configuration information on a USB device and restoring it on one or more computers. ● Execute self-tests on a sp ecified ATA hard drive (when su pported by drive). ● Enable or dis[...]

Computer Setup—File NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-2 Computer Setup— File Option Description System Information Lists: ● Product name ● SKU number ● Processor type/speed/stepping ● Cache size (L1/L2/L3) (dual core processors ha ve this listed twice) ● Inst[...]

Computer Setup—Storage NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-3 Computer Setup—Storage Option Description Device Configuration Lists all installed BIOS-controlled storage devices. When a device is selected, detailed informat ion and options are displayed. The following opti[...]

Table 3-3 Compu ter Setup—Storage (continued) Storage Options eSATA Port Allows you to set a SATA port as an eSATA port fo r use with an external drive. Default is enabled. This setting affects only the port with the black con nector, labeled as eSATA on the system board. This port should have the e SATA back panel conne ctor attached to use eSAT[...]

Table 3-3 Compu ter Setup—Storage (continued) DPS Self-Test Allows you to execute self-tests on ATA hard dr ives capable of performing the Drive Protection System (DPS) self-tests. NOTE: This selection will only appear when at leas t one drive capable of pe rforming the DPS self-tests is attached to the system. Boot Order Allows you to: ● EFI B[...]

Computer Setup—Security NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-4 Com puter Setup—Securi ty Option Description Setup Password Allows you to set and enable a setup (a dministrator) password. NOTE: If the setup password is set, it is required to change Compu ter Setup options,[...]

Table 3-4 Com puter Setup—Securi ty (continued) Device Security Allows you to set Device Available/Device Hidden (default is Device Availa ble) for: ● Embedded security device ● System audio ● USB controller (varies by model) ● Network controller NOTE: You must disable AMT before trying to hide the network controller. ● Serial port ● [...]

Table 3-4 Com puter Setup—Securi ty (continued) Master Boot Record Security Enables/disables Master B oot Record (MBR) security. The MBR contains information neede d to successf ully boot from a disk and to access the data stored on the disk. Master Boot Record Securi ty may preven t unintentional or malicious changes to the MBR, such as those ca[...]

Table 3-4 Com puter Setup—Securi ty (continued) System Security (these options are hardware dependent) Data Execution Prevention (enable/ disable) - Helps prevent oper ating system security breaches. Default is enabled. SVM CPU Virtualization (enable/disable). Contro ls the virtualization fea tures of the processor. Changing this setting requires[...]

Table 3-4 Com puter Setup—Securi ty (continued) DriveLock Sec urity Allows you to assign or modify a master or us er password for hard drives. When this feature is enabled, the user is prompted to provide one of the DriveLock passwords du ring POST. If neither is successfully entered, the hard drive will re main inaccessible until one of the pass[...]

Computer Setup—Power NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-5 Computer Setup—Power Option Description OS Power Management ● Idle Power Savings—Extended/Normal. Allows certain operating systems to decrease the processors power consumption when the processor is idle. Defa[...]

Computer Setup—Advanced NOTE: Support for specific Computer Setup op ti ons may vary depend ing on the hardware configuration. Table 3-6 Com puter Setup—Adva nced (for advanced use rs) Option Heading Power-On Options Allows you to set: ● POST mode (QuickBoot, Clear Memory, FullBoot, or FullBoot Ev ery x Days). ◦ QuickBoot (default) = Do not[...]

Table 3-6 Com puter Setup—Adva nced (for advanced users) (co ntinued) BIOS Power-On Allows you to set the computer to turn on automatically at a time you specify. Onboard Devices Allows you to set resources for or disable Legacy de vices. Select the Legacy device's IRQ, DMA, and I/O Range. The settings may not take effect for all operating s[...]

Table 3-6 Com puter Setup—Adva nced (for advanced users) (co ntinued) VGA Configuration Displayed only if there is an add-in video card in the system. Allows you to specify which VGA controller will be the “boot” or prima ry VGA controller. AMT Config uration Allows you to set: ● AMT (enable/disable). Allows you to en able or disable functi[...]

4 Illustrated parts catalog Microtower (MT) chassis spare parts Computer major components Item Description Spare part number (1) Front bezel For use in all countries and regions except C hina 689377-001 For use in China 689378-001 5.25-inch bezel blank (optical drive; not illustrated) 570838-001 Microtower (MT) ch assis spare parts 25[...]

Item Description Spare part number 3.5-inch bezel blank (not illustrated) 583653-001 (2) Access panel 646825-001 (3) Power supply 320W, 90% efficient 613764-001 320W, standard 613765-001 (4) System board (includes replacement thermal material) For use in models without Windows 8 657239-001 For use in models with Windows 8 Standard 657239-501 For us[...]

Item Description Spare part number G640, 2.8 GHz, 3-MB L3 cache 691935-001 G630, 2.7 GHz, 3-MB L3 cache 665122-001 Intel Celeron processors G555, 2.7 GHz, 2-MB L3 cache 704227-001 G550, 2.6 GHz, 2-MB L3 cache 691934-001 G540, 2.5 GHz, 2-MB L3 cache 665119-001 G530T, 2.0 GHz, 2-MB L3 cache 665118-001 G465, 1.9 GHz, 1.5-MB L3 cache 706883-001 G460, 1[...]

Item Description Spare part number (4) Power switch/LED assembly 646828-001 (5) SATA cable , 18 inch, 1 straight end, 1 angled end (labeled; no t illustrated) 646830-001 (6) SATA cable , 17.7 inch, 2 straight ends 639959-001 DMS-59 to dual VGA cable 463023-001 Adapter, DisplayPort to VGA 632484-001 Adapter, DisplayPort to DVI 662723-001 Adapter, DV[...]

Item Description Spare part number (6) Rear chassis fan 636922-001 (7) Printer port, PCI card (not illustrated) 638817-001 Fan duct assembly 646 824-001 Serial port, PCI card (not illustrated) 638815-001 2.5-in drive adapter (not illustrated) 586721-001 Hard drive conversion bracket 397117-001 Grommet, hard drive isolation , blue (not illustrated) [...]

Drives Description Spare part number Hard drive 1-TB, 7200-rpm 636930-001 500-GB, 10000-rpm 683923-001 500-GB, 7200-rpm 636929-001 320-GB, 7200-rpm, 2.5-inch 634824-001 250-GB, 10000-rpm 683922-001 250-GB, 7200-rpm 636927-001 256-GB Solid-state Drive (SSD), self-encrypting (SED), SATA 6.0 680020-001 160-GB Solid-state Drive (SSD), SATA 3.0 646809-0[...]

Description Spare part number Intel PRO/1000CT2 NIC, includes bracket 635523-001 HP WLAN 802.11 g/n 1x2 PCIe NIC 538048-001 Sequential part number listi ng Spare part number Description 330458-001 Screw Kit 336445-001 Feet 393956-001 Screw Kit - tamper r esistant screws 397117-001 Hard dr ive conversion bracket 450712-001 Grommet, hard drive isolat[...]

Spare part number Description 632486-001 nVidia Quadro NVS300 PCIe x16 graphics card, 51 2 MB (not for use with Windows 8 ) 633756-001 SATA power e xtension cable 634824-001 320-GB, 7200- rpm hard drive, 2.5 inch, SED 635523-001 Intel PRO/1000CT2 N IC, includes bracket 636166-001 Card r eader, 22-in-1 636917-001 USB powere d speakers 636922-001 Cha[...]

Spare part number Description 656792-001 Blu-ray BD-RW DL drive 657239-001 System board for use in models without Wi ndows 8 (includes replacement ther mal material) 657239-501 System board for use in models with Window s 8 Standard (include s replacement thermal material) 657239-601 System board for use in models with Windows 8 Professional (inclu[...]

Spare part number Description 689378-001 Front bezel for use in China 689578-001 Intel Core i3 3225 processor (3.4-GHz, 3-MB L3 cache, 55-W) 691934-001 Intel Celeron G550 processor (2.6-GHz, 2-MB L3 cache) 691935-001 Intel Pentium G640 proce ssor (2.8-GHz, 3-MB L3 cache) 691936-001 Intel Pentium G870 proce ssor (3.1-GHz, 3-MB L3 cache) 696442-001 5[...]

Small Form Factor (SFF) chassis spare parts Computer major components Item Description Spare part number (1) Front bezel 687950-001 Bezel blank (optical drive; not illustrated) 570838-001 Bezel blank (diskette drive; not illustrated) 583653-001 (2) Access panel 646815-001 (3) Power supply 240W, 90% efficient 613762-001 240W, standard 613763-001 (4)[...]

Item Description Spare part number Memory modules (PC3-12800, 1600 -MHz; not illustrated) 8-GB 689375-001 4-GB 671613-001 2-GB 671612-001 Processors (include replacement thermal material; not illustrated ) Intel Core i7 processor 3770, 3.4 GHz (turbo up to 3.9-GHz), 8-MB L3 cache, 77W 688164-001 2600, 3.4 GHz (turbo up to 3.8-GHz), 8-MB L3 cache, 9[...]

Cables Item Description Spare part number (1) Front I/O and power switch assembly 636926-001 (2) SATA cable , 19.5 inch, 2 straight ends 638813-001 (3) SATA drive power cable 636923-001 SATA cable , 25.2 inch, 1 straight end, 1 angled end (not illustrated) 638814-001 DMS-59 to dual VGA cable 463023-001 Adapter, DisplayPort to VGA 632484-001 Adapter[...]

Misc parts Item Description Spare part number (1) Chassis fan 645327-001 (2) Fan duct (not illustrated) 636921-001 (3) Heat sink (includes replacement t hermal material) 645326-001 (4) Speaker 636925-001 (5) Solenoid lock 641471-001 (6) Printer port, PCI card 638817-001 (7) Hood sensor 638816-001 Rubber feet 583654-001 Chassis stand 587451-001 38 C[...]

Item Description Spare part number Serial port, PCI card (not illustrated) 638815-001 2.5-in drive adapter (not illustrated) 586721-001 Hard drive conversion bracket 397117-001 Grommet, hard drive isolation , blue (not illustrated) 450712-001 Card reader, 22-in-1 (not illustrated ) 636166-001 USB powered speakers (not illustrated) 636917-001 Mouse [...]

Drives Description Spare part number Hard drive 1-TB, 7200-rpm 636930-001 500-GB, 10000-rpm 683923-001 500-GB, 7200-rpm, 2.5-inch, SED 696442-001 500-GB, 7200-rpm 636929-001 320-GB, 7200-rpm, 2.5-inch 634824-001 250-GB, 10000-rpm 683922-001 250-GB, 7200-rpm 636927-001 256-GB Solid-state Drive (SSD), self-encrypting (SED), SATA 6.0 680020-001 180-GB[...]

Description Spare part number Intel PRO/1000CT2 NIC, includes bracket 635523-001 HP WLAN 802.11 b/g/n minicard 538048-001 Sequential part number listi ng Spare part number Description 330458-001 Screw Kit 393956-001 Screw Kit - tamper r esistant screws 397117-001 Hard dr ive conversion bracket 450712-001 Grommet, hard drive isolatio n, blue 463023-[...]

Spare part number Description 632486-001 nVidia Quadro NVS300 PCIe x16 graphics card, 51 2 MB (not for use with Windows 8 ) 633756-001 SATA power e xtension cable 634824-001 320-GB, 7200- rpm hard drive, 2.5 inch, SED 635523-001 Intel PRO/1000CT2 N IC, includes bracket 636166-001 Card r eader, 22-in-1 636917-001 USB powere d speakers 636921-001 Fan[...]

Spare part number Description 657239-001 System board for use in models without Wi ndows 8 (includes replacement ther mal material) 657239-501 System board for use in models with Window s 8 Standard (include s replacement thermal material) 657239-601 System board for use in models with Windows 8 Professional (includes replacement thermal material) [...]

Spare part number Description 691936-001 Intel Pentium G870 proce ssor (3.1-GHz, 3-MB L3 cache) 696422-001 500-GB har d drive, 7200-rpm, 2.5-inch, SED 696622-001 180-GB Solid- state drive, SATA 2.0 697246-001 AMD Radeon HD6350 PCIe x16 graphics card, 512 MB (for u se with Windows 8) 700510-xx1 Keyboard, washable, for use in models with Windows 8 70[...]

5 Routine Care, SATA Drive Guidelines, and Disassembly Preparation This chapter provides general service information for the computer. Ad herence to th e procedures and precautions described in this chapter is esse ntial for proper service. CAUTION: When the computer is plugged in to an AC power source, voltage is always applied to the system board[...]

Removing DIPs from vinyl tray Removing DIPs from Styrofoam Removing bubble pack from PCB Packing PCBs in foam-lined box 2,000 V 3,500 V 7,000 V 5,000 V 4,000 V 5,000 V 20,000 V 11,000 V 11,500 V 14,500 V 26,500 V 21,000 V These are then multi-packaged inside p lastic tubes, trays, or Styrofoam. NOTE: 700 volts can degrade a product. Preventing Elec[...]

Grounding the Work Area To prevent sta tic damage at the work area, us e the following precautions : ● Cover the work surface with appr oved static-dissipa tive material. Provide a wrist strap connected to the work surface and properly grou nded tools and equ ipment. ● Use static-dissipative mats, foot st raps, or air ionizers to gi ve added pr[...]

Operating Guidelines To prevent ov erheating and to help p rolong the life of the computer: ● Keep the computer away from excessive mo isture , dire ct sunlight, and extremes of heat a nd cold. ● Operate the computer on a sturdy, level surfac e. Leave a 10.2-cm (4-i nch) clearance on all vented sides of the comp uter and above th e monitor to p[...]

To clean the co mputer case, follow th e procedures described below: ● To remove light sta ins or dirt, use plain water with a clean, lint-free cloth or swab. ● For stronger stains, use a mild dishwashing liq uid diluted with water. Rinse we ll by wiping it with a cloth or swab dampen ed with clear water. ● For stubborn stains, use isop ropyl[...]

Cleaning the Mouse Before cleanin g the mouse, ensure that the power to the compu ter is turned off. ● Clean the mouse ball by first removing the retaining plate and the ball from the ho using. Pull out any debris from th e ball socket and wipe the ball with a clean, dry cloth befo re reassembly. ● To clean the mou se body, follow the p rocedur[...]

Cables and Connectors Most cables used throu ghout the unit are flat, fl exible cables. Th ese cables must be handled with care to avoid damage. Apply onl y the tension required to sea t or unseat the cables during insertion or removal from the conne ctor. Handle cables by the co nnector whenever possible . In all cases, avoid bending or twisting t[...]

SATA Hard Drives Serial ATA Hard Drive Characteristics Number of pins/conductors in data cable 7/7 Number of pins in power cable 15 Maximum data cable length 39.37 in (100 cm) Data interface voltage differential 400-700 mV Drive voltages 3.3 V, 5 V, 12 V Jumpers for configuring drive N/A Data transfer rate 3.0 Gb/s SATA Hard Drive Cables SATA Data [...]

● Some flat ribbon cables come prefolded . Neve r change the folds on the se cables. ● Do not bend an y cable sharply. A sharp bend can br eak the interna l wires. ● Never bend a SATA data cable ti ghter than a 30 mm (1 .18 in) radius. ● Never crease a SATA data cable. ● Do not rely on comp onents like the drive cage, p o wer supply, or c[...]

6 Removal and Replacement Procedures Microtower (MT) Chassis Adherence to the p rocedures and pr ecautions de scribed in this chapt er is essential fo r proper servic e. After completing all necessary removal and replacemen t procedures, run the Diagnostics utility to verify that all compo nents operate properly. NOTE: Not all features listed in th[...]

Computer Access Panel Description Spare part num ber Access panel 646825-001 To access internal components, yo u must remove the access panel: 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ) 2. Loosen the two captive thu mbscrews (1) that secure the access panel to the computer chassis. 3. Use the handle located [...]

Front Bezel Description Spare part num ber Front bezel for use in all countries and regio ns except China 689377-001 Front bezel for use in China 689378-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ) 2. Remove the access pan el ( Computer Access Pane l on page 55 ) 3. Lift up the three tabs on the side of th[...]

Front Bezel Security The front bezel can be lock ed in place by installing a security screw provided by HP. To install the security screw: 1. Remove/disengage an y security devices that prohibit opening the computer. 2. Remove all removable m edia, such as compact discs o r USB flash drives, from the computer. 3. Turn off the compu ter properly thr[...]

8. Install the screw through the inte rior of the front of the chassis into the fro nt bezel. The screw hole is located toward the middle of th e right ed ge of the chassis between the hard drive bay a nd speaker. Figure 6-4 Installing the Front Bezel Security Screw 9. Replace the access pane l. 10. Reconnect the power cord an d turn on the compute[...]

Bezel Blanks Description Spare part num ber 3.5-inch beze l blank 583653-001 5.25-inch bezel blank, optical drive 570838-001 On some models, th ere are bezel blanks coverin g the 3.5-inch and 5.25-in ch drive bays that need to be removed befo re installing a drive. To remove a bezel b lank: 1. Remove the access pan el ( Computer Access Pane l on pa[...]

Memory Description Spare part num ber 8-GB, PC3-12800 689375-001 4-GB, PC3-12800 671613-001 2-GB, PC3-12800 671612-001 The computer comes with double data rate 3 syn chrono us dynamic random access memory (DDR3- SDRAM) dual inline memo ry modules (DIMMs). DIMMs The memory sockets on the system board can be po pulated with up to four indust ry-stand[...]

The system will au tomatically operate i n single channel mode, d ual channel mode, or flex mode, depending on how the DIMMs are i nstalled. ● The system will operate in singl e channel mode if the DIMM so ckets are populated in one channel on ly. ● The system will operate in a higher-performing dual channel mode if th e total memory capacity o[...]

3. Open both latches of the memory module socket (1) , and insert the memory modul e into the socket (2) . Figure 6-6 Installing a DIMM NOTE: A memory module can be installed in o nly one way. Match the notch on the module with the tab on the memory socket. Populate the black DIMM sockets before the white DIMM sockets. For maximum performance, popu[...]

Expansion Cards Description Spare part num ber nVidia GeForce GT630 PCIe x16 graphics card, 2 GB (not for use w ith Windows 8) 684591-001 nVidia GeForce GT630 PCIe x16 graphics card, 2 GB (for use with Windows 8 ) 702084-001 nVidia Quadro NVS310 PCIe x16 graphics card, 512 MB 680653-001 nVidia Quadro NVS300 PCIe x16 graphics card, 512 MB (not for u[...]

4. Release the slot cover rete ntion latch that secure s the PCI slot covers by lifting the green tab on the latch and ro tating the la tch to the open po sition. Figure 6-7 Opening th e Expansion Slot Reta iner 5. Before installing an expansion ca rd, remove the expansion slot co ver or the existing expansion card. NOTE: Before removing an insta l[...]

b. If you are removing a standard PCI card or PC I Express x1 card, hold the card at each end, and carefully rock it back a nd forth until th e connectors pull fre e from the socket. Pull the expansion card straigh t up from the socket t hen away from the inside of the chassis to release it from the chassis frame. Be sure not to scrape the card aga[...]

7. If you are not installi ng a new expansion card , in stall an expa nsion slot cover to close the open slot. CAUTION: After remo ving an expansion card, you must replac e it with a new card or expansion slot cover for proper coolin g of internal components during op eration. 8. To install a new expansio n card, hold the card just above the expans[...]

System Board Connections Refer to the following illustrations and tables to identify the system board conn ectors for your model. Figure 6 -12 System Board Connections Table 6-1 System Board Conne ctions No. System Board Connec tor System B oard Label Color Component 1 DIMM4 (Channel A) DIMM4 w hite Memory Module 2 DIMM3 (Channel A) DIMM3 b lack Me[...]

Table 6-1 System Board Connections (continue d) No. System Board Connec tor System B oard Label Color Component 18 PCI Express x1 X1PCIEXP2 b lack Expansion Card 19 PCI Express x16 X16PCIEXP black Expansio n Card 20 PCI PCI1 white Expansion Card Drives Description Spare part num ber DVD±RW d rive 660408-001 DVD-ROM d rive 581599-001 Blu-ray BD-Wri[...]

● Connect a media card reader USB cable to the USB connector on the system board labeled MEDIA. ● The power cabl e for the SATA optical drives is a two -headed cable th is is plugged into the system board with the first connector routed to the top 5.25-inch bay and the second connector routed to the bottom 5.25-inch bay. ● The power cable for[...]

CAUTION: To prevent loss of work and damage to the compu ter or drive: If you are inserting or removing a drive, shut down the operating system properly, turn off the computer, and unplu g the power cord. Do not remove a drive whi le the computer is on or in sta ndby mode. Before hand ling a drive, ensure that you are dischar g ed of static electri[...]

Removing a 5.25-inch or 3.5-in ch Drive from a Drive Bay CAUTION: All removable media should be taken out of a drive before removin g the drive from the computer. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ) 2. Remove the access pan el ( Computer Access Pane l on page 55 ) 3. Remove the front bezel ( Front Bez[...]

5. A latch drive bracket with release tabs secures th e drives in the d rive bay. Lift the release tab on the latch drive bracket (1) for the drive you want to remove , then slide the drive from its drive b ay (2) . Figure 6-16 Removing the Drives Installing a 5.25-inch or 3.5- inch Drive into a Drive Bay 1. Prepare the compu ter for disassembly ( [...]

5. Install four M3 metric guide screws in the lower holes on each side of the drive. HP has provided eight extra M3 metric guide screws on the fron t of the chassis, under the fron t bezel. The M3 metric guide screws are bla ck. Refer to Drives on page 68 for an illustration of the extra M3 metric guide screws location. NOTE: When repla cing the dr[...]

b. If your are installing a media card reader, connect the USB cable to the USB system board connector labeled MEDIA. Figure 6-19 Connecting the Media Card Re ader USB Cable 8. If installing a new drive, conn ect the opposite end of the data cable to the appropriate system board connector. NOTE: If you are installing a new SATA optical drive, co nn[...]

Removing a Hard Drive from a Drive Bay NOTE: Before you remove th e old hard drive, be sure to back up the data from the o ld hard drive so that you can transfer the data to the new hard drive. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ) 2. Remove the access pan el ( Computer Access Pane l on page 55 ) 3. Dis[...]

3. Install guide screws on the sides of the drive. If you are installing a 2.5-inch drive, you must install the drive in an adapter bracket. NOTE: The hard drive use s 6-32 isolation mounting guide screws. Four extra guid e screws are installed on the e xterior of the hard drive ba ys. The HP-sup plied isolation mounting guid e screws are silver an[...]

◦ Secure the drive to the bay ad apter bracket by installing fo ur black M3 adapter bracket screws through the sides of the brac ket into the dri ve. Figure 6-23 Securing the D rive in the Adapter Brac ket ◦ Install four 6-32 silver and bl ue isolation mounting guide screws in the a dapter bracket (two on each side of the bracket). Figure 6-24 [...]

4. Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until the drive sna ps into place. The bottom bay is for the primary hard d rive. The upper bay is for an optional secondary h ard drive. Figure 6-25 Sliding a Hard Drive into the Drive Bay 5. Connect the p ower cable and data cabl e to the back of th[...]

Front Fan Assembly Description Spare part num ber Front fan assembly 585884-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ). 2. Remove the access pan el ( Computer Access Pane l on page 55 ). 3. Remove the cables from the clip on the top of the fan assembly. Figure 6-26 Re moving the cables from atop th e fro[...]

5. Press the lever that secures the assembly to the chassis (1 ) , pivot the assemb ly forward toward the front of the computer (2) , and then lift the assembly stra ight up and out of the comp uter (3) . Figure 6-27 Removing the front fan assembl y To reinstall the front fan, reverse the removal procedu re. 80 Chapter 6 Remova l and Replacement Pr[...]

Front I/O Assembly Description Spare part num ber Front I/O assembly 646827-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ). 2. Remove the computer access pa nel ( Computer Access Panel on page 55 ). 3. Remove the front bezel ( Front Bezel on page 56 ). 4. Remove the front fan ( Front Fan Assemb ly on page 79[...]

Power Switch/LED Assembly Description Spare part num ber Power switch/LED assembly 646828-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ). 2. Remove the access pan el ( Computer Access Pane l on page 55 ). 3. Remove the front bezel ( Front Bezel on page 56 ). 4. Remove the front fan ( Front Fan Assemb ly on p[...]

Heat sink Description Spare part num ber Heat sink 645326-001 WARNING! To reduce risk of pe rsonal injury from hot surface s, allow the inte rnal system components to cool before touch ing. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ). 2. Remove the computer access pa nel ( Computer Access Panel on page 55 ). [...]

5. Lift the heat sink from at op the proc essor. When reinstalling the heat sink, ma ke sure that i ts bottom has been cleaned with an alcohol wipe and fresh thermal grease has been app lied to the top of the proce ssor. CAUTION: Heat sink retaining screws sho uld be tighte ned in diagonal ly opposite pairs (as in an X) to evenly seat the heat sin [...]

Processor Description Spare part num ber Intel Core i7 processor 3770, 3.4 GHz (turbo up to 3.9 GHz), 8-MB L3 cache, 77W 688164-001 2600, 3.4 GHz (turbo up to 3.8 GHz), 8-MB L3 cache, 95W 638632-001 Intel Core i5 processors 3570, 3.4 GHz, 6-MB L3 cache 688162-001 3470, 3.2 GHz, 6-MB L3 cache 687943-001 2400, 3.1 GHz, 6-MB L3 cache 638630-001 Intel [...]

4. Rotate the locking lever to its full open positio n (1) . 5. Raise and rota te the microprocessor retain er to its fully open position (2) . 6. Carefully lif t the proce ssor from the socket (3) . CAUTION: Do NO T handle the pins in the processor socket. Thes e pins are very fragile and handling them co uld cause irreparable da mage. Once pins a[...]

To install a new processor: 1. Place the processor in its socket a nd close the retainer. 2. Secure the lo cking lever. If reusing the existing heat sink, go to step 3. If using a new heat sink, go to step 5. 3. If reusing the exist ing heat sink, apply th e thermal grease pro vided in the spares kit t o the top of the processo r. 4. Clean the bott[...]

Speaker Description Spare part num ber Speaker 645330-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ). 2. Remove the access pan el ( Computer Access Pane l on page 55 ). 3. Remove the front fan assembly ( Front Fan Assembly on page 79 ). 4. Disconnect the spea ker wire from the system board connector labeled [...]

Rear Chassis Fan Description Spare part num ber Rear chassis fan 636922-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ). 2. Remove the access pan el ( Computer Access Pane l on page 55 ). 3. Remove the four silver Phillips screws that secure the f an to the chassis. Figure 6-32 Rear fan screws 4. Disconnec t [...]

5. Lift the fan out of the chassis (2) . Figure 6-33 Removing the rear fan To install the fan asse mbly, reverse the re moval procedure. Be sure to orient the air flow out of the unit. 90 Chapter 6 Remova l and Replacement Procedure s Microtower (MT) Chassis[...]

Power Supply Description Spare part num ber Power supply, 320W, 90% efficient 613764-001 Power supply, 320W 613765-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ). 2. Remove the access pan el ( Computer Access Pane l on page 55 ). 3. Disconnect the power cables from the white syst em board connector labe led [...]

7. Slide the power supply toward th e front of the computer (2) , rotate toward the fan so the power supply clears the lip on the top of the chas sis, a nd then lift the power supply out o f the chassis (3) . Figure 6-35 Removing the power supply To install the po wer supply, reverse the removal procedure. 92 Chapter 6 Remova l and Replacement Proc[...]

System Board Description Spare part num ber System board (includes thermal material) 657239-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 54 ). 2. Remove the access pan el ( Computer Access Pane l on page 55 ). 3. Remove the front fan assembly ( Front Fan Assembly on page 79 ). 4. When replac ing the system boar[...]

7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis Adherence to the p rocedures and pr ecautions de scribed in this chapt er is essential fo r proper servic e. After completing all necessary removal and replacemen t procedures, run the Diagnostics utility to verify that all compo nents operate properly. NOTE: Not all features list[...]

Access Panel Description Spare part num ber Access panel 646815-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. If the computer is o n a stand, re move the compute r from the stand. 3. Lift up on the a ccess panel hand le (1) then lift the access panel off the computer (2) . Figure 7-1 Removing the access[...]

Front Bezel Description Spare part num ber Front bezel 687950-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. Remove the access pan el ( Access Panel on page 95 ). 3. Lift up the three tabs on the side of the bezel (1) , then rotate the bezel off the chassis (2) . Figure 7-2 Removing the front bezel To in[...]

Front Bezel Security The front bezel can be lock ed in place by installing a security screw provided by HP. To install the security screw: 1. Remove/disengage an y security devices that prohibit opening the computer. 2. Remove all removable m edia, such as compact discs o r USB flash drives, from the computer. 3. Turn off the compu ter properly thr[...]

9. Install the security screw next to the midd le front bezel release tab to secure th e front bezel in place. Figure 7-4 Installing the Front Bezel Security Screw 10. Replace the access panel. 11. If the computer wa s on a stand, replace th e stand. 12. Reconnect the power cord an d turn on the compute r. 13. Lock any security devices that we re d[...]

Bezel Blanks Description Spare part num ber 3.5-inch beze l blank 583653-001 5.25-inch bezel blank, optical drive 570838-001 On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch extern al drive bays that need to be removed befo re installing a drive. To remove a bezel blank: 1. Remove the access pan el ( Access Panel on page 9[...]

Memory Description Spare part num ber 8-GB, PC3-12800 689375-001 4-GB, PC3-12800 671613-001 2-GB, PC3-12800 671612-001 The computer comes with double data rate 3 syn chrono us dynamic random access memory (DDR3- SDRAM) dual inline memo ry modules (DIMMs). DIMMs The memory sockets on the system board can be po pulated with up to four indust ry-stand[...]

The system will au tomatically operate i n single channel mode, d ual channel mode, or flex mode, depending on how the DIMMs are i nstalled. ● The system will operate in singl e channel mode if the DIMM so ckets are populated in one channel on ly. ● The system will operate in a higher-performing dual channel mode if th e total memory capacity o[...]

4. Open both latches of the memory module socket (1) , and insert the memory modul e into the socket (2) . Figure 7-6 Installing a DIMM NOTE: A memory module can be installed in o nly one way. Match the notch on the module with the tab on the memory socket. Populate the black DIMM sockets before the white DIMM sockets. For maximum performance, popu[...]

Expansion Card Description Spare part num ber nVidia Quadro NVS310 PCIe x16 graphics card, 512 MB 680653-001 nVidia Quadro NVS300 PCIe x16 graphics card, 512 MB (not for u se with Windows 8) 632486-001 nVidia Quadro NVS300 PCIe x16 graphics card, 512 MB (for use with Windows 8) 700578-001 nVidia GF505 PCIe x16 graphics card, 512 MB (for use only in[...]

4. Release the slot cover rete ntion latch that secure s the PCI slot covers by lifting the green tab on the latch and ro tating the la tch to the open po sition. Figure 7-7 Opening th e Expansion Slot Reta iner 5. Before installing an expansion ca rd, remove the expansion slot co ver or the existing expansion card. NOTE: Before removing an insta l[...]

b. If you are removing a standard PCI card or PC I Express x1 card, hold the card at each end, and carefully rock it back a nd forth until th e connectors pull fre e from the socket. Pull the expansion card straigh t up from the socket (1) then away from the in side of the chassis to release it from the chassis frame (2) . Be sure n ot to scrape th[...]

7. If you are not installi ng a new expansion card , in stall an expa nsion slot cover to close the open slot. CAUTION: After remo ving an expansion card, you must replac e it with a new card or expansion slot cover for proper coolin g of internal components during op eration. 8. To install a new expansio n card, hold the card just above the expans[...]

System Board Connections Refer to the following illustration and table to id entify the system board co nnectors for your model. Figure 7 -12 System Board Connections Table 7-1 System Board Conne ctions No. System Board Connec tor System B oard Label Color Component 1 DIMM4 (Channel A) DIMM4 w hite Memory Module 2 DIMM3 (Channel A) DIMM3 b lack Mem[...]

Table 7-1 System Board Connections (continue d) No. System Board Connec tor System B oard Label Color Component 18 PCI Express x1 X4PCIEXP black Expansio n Card 19 PCI Express x16 X16PCIEXP black Expansio n Card 20 PCI PCI white Expansion Card Drives Description Spare part num ber DVD±RW d rive 660408-001 DVD-ROM d rive 581599-001 Blu-ray BD-RW Su[...]

Drive Positions Figure 7 -13 Drive Positions Table 7-2 Drive Positions 1 3.5-inch internal hard drive bay 2 3.5-inch drive bay for optional drives (media card reade r shown) 3 5.25-inch drive bay for optional drives (optical drive shown) NOTE: The drive configuration on your computer m ay be different than the drive configuration shown above. To ve[...]

remove the four silver a nd blue 6-32 isolatio n mounting guide screws fro m the old hard drive and install them in the ne w hard drive. Figure 7 -14 Extra Guide Screw Locations No. Guide Screw Device 1 Black M3 Metric Screws All Drives (except primary and secondary h ard drives) 2 Silver 6-32 Standard Screws Secondary Hard Drive There are at total[...]

4. If removing an opti cal drive, disconnect the po wer cable and data cable from the rea r of the optical drive. CAUTION: Whe n removing the cables, pull the tab or connector in stead of the cable itself to avoid damaging the cable. 5. Rotate the drive ca ge back down to its normal po sition. CAUTION: Be careful not to pinch a ny cables or wires w[...]

4. Install four M3 metric guide screws in the lower holes on each side of the drive. HP has provided four extra M3 metric guide screws on the front of the chassi s, under the front beze l. The M3 metric guide screws are bla ck. Refer to Installing and Removing Drives on page 109 for an illustration of the extra M3 metric guide screws location. NOTE[...]

9. Connect the power ca ble and data cable to the rear of the optical drive. NOTE: The power cable fo r the optical drive is a t h ree-headed cable that is routed from the system board to the h ard drive, then to the rear of the optical drive. 10. Rotate the drive cage back down to its normal position. CAUTION: Be careful not to pinch a ny cables o[...]

Removing a 3.5-inch Drive from a Drive Bay CAUTION: All removable media should be taken out of a drive before removin g the drive from the computer. The 3.5-inch drive is loca ted underneath the 5.25 -inch drive. You must remove th e 5.25-inch drive before removing the 3.5-inch drive. 1. Follow the procedure in Removing a 5.25-inch Drive from a Dri[...]

Installing a 3.5-inch Drive into a Drive Bay The 3.5-inch bay is lo cated underne ath the 5.25-inch drive. To insta ll a drive into the 3.5-i nch bay: NOTE: Install guide screws to ensure the drive will line up correctly in the dri ve cage and lock in place. HP has provided extra gu ide screws for the drive bays (four 6-3 2 standard screws and fo u[...]

b. If installing a media card reader, co nnect the USB cable from th e media card read er to the USB connector on the system board l abeled MEDIA. Figure 7-22 Connecting the Media Card Re ader USB Cable NOTE: Refer to System Board Connections on p age 107 for an illustration of the system board drive connectors. 6. Replace the 5.25-inch drive. 7. R[...]

4. Rotate the power su pply to its upright position. The hard drive is lo cated beneath the power supply. Figure 7-23 Raising the Power Supply 5. Disconnect the power cabl e and data cabl e from the ba ck of the hard drive. 6. Press down on the green release l atch next to the hard drive (1) . While holding the la tch down, slide the drive forwa rd[...]

7. To install a hard drive, you must tr ansfer th e silver and blue isolat ion mounting guide screws from the ol d hard drive to the new har d drive. Figure 7-25 Installing Hard Drive Guide Screws 8. Align the guide screws with the slots on the cha ssis drive cage , press the hard drive dow n into the bay, then slide it back until it stops and lock[...]

Fan duct Description Spare part num ber Fan duct 636921-001 The fan duct sits between the front fan and the heat sink. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. Remove the access pan el ( Access Panel on page 95 ). 3. Lift the fan duct straight up ou t of the chassis. Figure 7-27 Removing the fan duct T[...]

Front Fan Assembly Description Spare part num ber Front fan 645327-001 The front fan assemb ly is attach ed to the fron t of the chassis. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. Remove the access pan el ( Access Panel on page 95 ). 3. Remove the front bezel ( Front Bezel on page 96 ). 4. Remove the ba[...]

7. Pull the assembly toward the rea r of the unit (2) , and then lift it out of the chassis. Figure 7-29 Removing the front fan To install the fron t fan, reverse the re moval procedure. Be sure to orient th e air flow into th e unit. Front Fan Assembly 121[...]

Hood Sensor Description Spare part num ber Hood sensor 638816-001 The hood sensor is attached in a slot in the rear of the chassis. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. Remove the access pan el ( Access Panel on page 95 ). 3. Unplug the sensor cable from the system board connect or labeled HSENSE ([...]

Front I/O, Power Switch Assembly Description Spare part num ber Front I/O and power switch assembly 636926-001 The front I/O and po wer switch/LEDs is one as sembly, attached to the front of the ch assis. Push the assembly into the ch assis to remove. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. Remove the[...]

8. Route the cables through the slots beneath the dr ive cage, rota te the asse mbly into the chassis (2) , and then remove the assembly from the co mputer. Figure 7-32 Removing the front I/O, po wer switch/LED assembly screw To install the front I/O an d power switch assembly, reverse the removal proced ure. NOTE: Be sure to correctly ro ute the c[...]

Speaker Description Spare part num ber Speaker 636925-001 The speaker is attached to the front of th e chassis under the rotating drive cage. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. Remove the access pan el ( Access Panel on page 95 ). 3. Remove the front bezel ( Front Bezel on page 96 ). 4. Rotate th[...]

Heat sink Description Spare part num ber Heat sink 645326-001 The heat sink is secured atop the processor with four cap tive Torx screws. The heat sink doe s not include a fan. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. Remove the access pan el ( Access Panel on page 95 ). 3. Remove the fan duct ( Fan du[...]

6. After loosenin g the Torx T15 scr ews (1) , lift the heat sink from atop the p rocessor (2) and set it on its side to keep from contaminatin g the work ar ea with thermal grease. Figure 7-35 Removing the heat sink When reinstalling the heat sink, ma ke sure that i ts bottom has been cleaned with an alcohol wipe and fresh thermal grease has been [...]

Processor Description Spare part num ber Intel Core i7 processor 3770, 3.4 GHz (turbo up to 3.9 GHz), 8-MB L3 cache, 77W 688164-001 2600, 3.4 GHz (turbo up to 3.8 GHz), 8-MB L3 cache, 95W 638632-001 Intel Core i5 processors 3570, 3.4 GHz, 6-MB L3 cache, 95W 688162-001 3470, 3.2 GHz, 6-MB L3 cache, 95W 687943-001 2400, 3.1 GHz, 6-MB L3 cache 638630-[...]

4. Remove the front fan assembly ( Front Fan Assembly on page 120 ). 5. Remove the heat sink ( Heat sink on p age 126 ). 6. Rotate the locking lever to its full open positio n (1) . 7. Raise and rota te the microprocessor retain er to its fully open position (2) . 8. Carefully lif t the proce ssor from the socket (3) . CAUTION: Do NO T handle the p[...]

2. Secure the locking lever. If reusing the existing hea t sink, go to step 3. If using a new heat sink, go to step 6. Figure 7-37 Removing the processor 3. If reusing the ex isting heat sink, clean the bo ttom of the heat sin k with the alcohol p ad provided in the spares kit. CAUTION: Before reinstalling th e heat sink you must clean the top of t[...]

Power Supply Description Spare part num ber Power supply, 90% efficient 613762-001 Power supply, standard 613763-001 WARNING! To reduce potential safety i ssues, only the power supply pr ovid ed with the compu ter, a replacement powe r supply provided by HP, or a power su pply purchased as an accessory from HP should be used with the comp uter. The[...]

7. Pull the power supply forward until the posts o n the power supply move forward in the power supply bracket, and th en lift the power supply straigh t up and out of the cha ssis. Figure 7-38 Removing the power supply To install the po wer supply, reverse the removal procedure. CAUTION: When installing the power su pply cables, make sure they are[...]

System Board Description Spare part num ber System board (includes thermal material) 657239-001 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. Remove the access pan el ( Access Panel on page 95 ). 3. When replac ing the system board, make sure the following components are removed from the defective system bo[...]

11. Lift up the front of the system board, and then pull the system board forwar d, up, and out of the chassis (2) . Figure 7-39 Removing the system board To install the system board, reverse the removal procedure. NOTE: When replacing the system board, you must also c hange the ch assis serial number in the BIOS. CAUTION: Before reinstalling the h[...]

Using the Small Form Fact or Computer in a Tower Orientation The Small Form Fa ctor computer can be used in a towe r orientation. T he HP logo plate o n the front bezel is adjustable for either desktop or tower orientation. 1. Prepare the compu ter for disassembly ( Preparation for Disassembly on page 94 ). 2. Orient the comput er so that its right[...]

8 Troubleshooting Without Diagnostics This chapter provide s information on how to iden tify and correct minor problems, such as USB devices, hard drive, optical drive, graphics, audio, memory, and software prob lems. If you encou nter problems with the co mputer, re fer to the tables in this chapter for probable causes and recommended solutions. N[...]

● Refer to the comprehensive online tech nical support at http://www.hp.com/ support . ● Refer to Helpful Hints on pa ge 137 in this guide. To assist you in reso lving problems online , HP Instant Supp ort Professional Ed ition provides you w ith self-solve di agnostics. If you n eed to contact HP support, use H P Instant Supp ort Professional [...]

● Wake the computer by pressing an y key on the keybo ard or pressing the power button . If the system remains in su spend mode, shut down th e comp uter by pressing and hold ing the power button for at least four seconds th en press the pow er button again to restart the co mputer. If t he system will not shut down, unplug the power cord, wait a[...]

Solving General Problems You may be able to easily resolve the g eneral pr obl ems described in this section . If a problem persists and you are unable to resolv e it yourself or if you fe el uncomfortable ab out performing the operation, contact an authorized dealer or reseller. WARNING! When the computer is plugged in to an AC power source, volta[...]

Cursor will not mo ve using the arrow keys on the ke ypad. Cause Solution The Num Lock key is turned on. Press the Num Lock key. The Num Lock light must be off if you want to use the arro w keys on the keypad. You can also disable or enable the Num Lock key in Computer Setup at Advanced > Device Options . There is no sound or sound volume is t o[...]

Table 8-1 Solving Gener al Problems (continue d) Poor performance. Cause Solution Virus resident on the hard drive. Run virus protection progr am. Too many applications running. Windows 7: 1. Close unnecessary applications to free up memory. 2. Add more memory. 3. Some applications run in the background and ca n be closed by right-clicking on their[...]

Computer powe red off automa tically and the Pow er LED flashes Red two times, onc e every second, followed by a two second pause, an d the computer beep s two times. (Beep s stop after fifth iterat ion but LEDs continue flashing). Cause Solution Processor thermal protection activated: A fan may be blocked or not turning. OR The heat sink is not pr[...]

Solving Power Problems Common causes and so lutions for po wer problems are listed in the f ollowing table. Table 8-2 Solving Power Problems Power supply shuts down intermittent ly. Cause Solution If equipped with a voltage selector, volta ge selector switch on rear of computer chassis (some mo dels) not switched to correct line voltage (115V or 23[...]

Power LED flashes Re d four times, onc e every second, follow ed by a two sec ond pause, and the co mputer beeps four times. (Beeps stop after fifth it eration but LEDs co ntinue flashing.) Cause Solution Power failure (power supply is overload ed). 1. If equipped with a voltage selector, check that the voltage selector, located on the rear of the [...]

Solving Hard Drive Problems Table 8-3 Solving Ha rd Drive Problems Hard drive error occurs. Cause Solution Hard disk has bad sectors or has failed. 1. In Windows 7, click Start , click Computer , and right- click on a driv e. Select Properties , and then select the Tools tab. Under Error-checking click Check Now . In Windows 8, on the Start screen [...]

Nonsystem disk/NTLDR missing message. Cause Solution The system is trying to start from the hard drive but the ha rd drive may have been damaged. 1. Perform Drive Protection System (DPS) testing in system ROM. System files missing or not properly installed. 1. Insert bootable media and restart the computer. 2. Boot to the windows installation media[...]

Computer seems to be loc ked up. Cause Solution Program in use has stopped responding to comma nds. 1. Use the task manager to close programs tha t do not respond. 2. Attempt the normal Windows “Shut Dow n” procedure. If this fails, press the power button for four or more seconds to turn off the power. To restart the computer, press the power b[...]

Solving Media Card Reader Problems Table 8-4 Solving Media Car d Reader Pr oblems Media card will not work in a digital camera after formatting it in Windows. Cause Solution By default, Windows will format any media card with a capacity greater than 32MB with the FAT3 2 format. Some digital cameras use the FAT (FAT16 & FAT12 ) format and can no[...]

Do not know how t o remove a media card correctly. Cause Solution The computer’s software is used to safe ly eject the card. In Windows 7, click Start , select Computer , right-click on the corresponding drive icon, and then select Eject . Pull the card out of the slot. In Windows 8, on the Start screen, typ e e , and then click File Explorer fro[...]

Solving Display Problems If you encounte r display problems, see the do cumentation that came with the monitor a nd to the common causes and solutions listed in the following table. Table 8-5 Solving Di splay Problems Blank screen (no video ). Cause Solution Monitor is not turned on and the monitor light is not on. Tu rn on the monitor and check th[...]

Blank screen and the p ower LED flashes Red five times, once every second, followed by a two se cond pause, and the computer beep s five times. (Be eps stop after fifth iteration but LEDs continue flashing.) Cause Solution Pre-video memory error. 1. Reseat DIMMs. Power on the system. 2. Replace DIMMs one at a time to isolate the faulty module. 3. R[...]

Blurry video or reque sted resolution cann ot be set. Cause Solution If the graphics controller was upgr aded, the correct grap hics drivers may not be loaded. Install the video drivers included in the upgrade kit. Monitor is not capable of displaying requested resolutio n. Change requested resolution. Graphics card is bad. Replace the graphics ca [...]

“Out of Range” displays on screen. Cause Solution Video resolution and refr esh rate are set higher than wha t the monitor supports. Restart the computer and enter Safe Mode. Change the settings to a supported setting then restart the computer so that the new settings take effect. To enter Safe Mode in Windows 7: 1. Restart the computer. 2. Pre[...]

Fuzzy focus; streaking, ghosting, or shadowing effects; horizontal scrolling lines; faint vertical bars; or unable to center the picture o n the screen (flat pa nel m onitors using an an alog VGA input c onnection only). Cause Solution Flat panel monitor’s internal digital conversi on circuits may be unable to correctly interpr et the output sync[...]

Solving Audio Problems If the computer ha s audio features a nd you enco unter audio problems, see the common cau ses and solutions listed in the foll owing table. Table 8-6 Solving Au dio Problems Sound cuts in and o ut. Cause Solution Processor resources are being used by other open applications. Shut down all open processor-intensive ap plicatio[...]

Table 8-6 Solving Au dio Problems (continu ed) Sound does not come out of the speaker o r headphones. Cause Solution Some applications can select which audio output device is used. Make sure the application has selected the correct aud io device. The operating system controls may be set to use a different audio device as the default output device t[...]

Table 8-6 Solving Au dio Problems (continu ed) There is no sound or sound volume is t oo low. Cause Solution Some applications can select which audio output device is used. Make sure the application has selected the correct aud io device. The operating system controls may be set to use a different audio device as the default output device than what[...]

Table 8-7 Solving Printer Problems (c ontinued) Printer prints garbled information. Cause Solution The cables may not be connected p roperly. Reconnect all cables. Printer memory may be overloaded. Reset the printer by turning it off for one minute, then turn it back on. Printer will not print. Cause Solution The printer may be out of pa per. Check[...]

Solving Keyboard and Mouse Problems If you encounte r keyboard or mouse problems, see the document ation that came with the equipmen t and to the commo n causes and solutio ns listed in the following tabl e. Table 8-8 Solving Key board Problems A wireless keyboard/mouse is no t working correctly. Symp toms include lagging mouse movemen t, jumpy mou[...]

Table 8-9 Solving Mou se Problems Mouse does not respond to movement or is too slow. Cause Solution Mouse connector is not properly plu gged into the back of the computer. Shut down the computer using the keybo ard. Windows 7: 1. Press the Ctrl and Esc keys at the same time (or press the Windows logo key) to display the Start menu. 2. Use the arrow[...]

Solving Hardware Installation Problems You may need to reconfigure the compu ter when you add or remove hardware, such as an addi tional drive or expansion card. If you install a plug an d play device, Windows auto matically recognizes the device and configures the computer. If you insta ll a non-p lug and play device, you must reconfigu re the com[...]

Computer will not start. Cause Solution Wrong memory modules we re used in the upgrade or memory modules were installed in the wrong location. 1. Review the documentation that came with the system to determine if you are using the correct memory modules and to verify the proper installation. NOTE: DIMM1 or XMM1 must always be installed. On all comp[...]

Power LED flashes Re d ten times, once every second, followed by a two second pause, and the computer beeps ten times. (Beeps stop after fifth ite ration but LEDs con tinue flashing.) Cause Solution Bad option card. 1. Check each option card by removing the cards one at time (if multiple cards), then power on the system to see if fault goes aw ay. [...]

Network driver does not detect netw ork controller. Cause Solution Network controller is disabled. 1. Run Computer Setup and enable networ k controller. 2. Enable the network controller in the o perating system using Device Manager. To access Device Manager in Windows 7, click Start , select Control Panel , and then sele ct Device Manager . To acce[...]

Diagnostics reports a failure. Cause Solution The cable is not secur ely connected. Ensure that the cable is securely attached to the network connector and that the other end of the cable is secure ly attached to the correct device. The cable is attached to the in correct connector. Ensure that the cable is attached to the correct connector. There [...]

Table 8-11 Solvin g Network Problems (continued) Network controller s tops working without apparent cause. Cause Solution The cable is not secur ely connected. Ensure that the cable is securely attached to the network connector and that the other end of the cable is secure ly attached to the correct device. The network controller is d efective. Con[...]

Table 8-12 Solving Memo ry Problems System will not bo ot or does not func tion properly after installing additional memory mod ules. Cause Solution A memory module is not installed in the DIMM1 or XMM1 socket. Ensure that a memory module is installed in the DIMM1 or XMM1 socket on the system board. This socket must be populated with a memory modul[...]

Solving Processor Problems If you encounte r processor problems, common ca uses and solutions are listed in the following table. Table 8-13 Solving Proc essor Pr oblems Poor performance is experienced. Cause Solution Processor is hot. 1. Make sure the airflow to the computer is not blocked. 2. Make sure the fans are connected and wor king properly [...]

Table 8-14 Solvi ng CD-ROM and DVD Problems (c ontinued) System will not bo ot from CD-ROM or DVD drive. Cause Solution Network Boot is enabled in Compu ter Setup. Run the Computer Setup utility and disable Network Boot in Security > Network Boot . Non-bootable CD in drive. Try a bootable CD in the drive. Boot order not corre ct. Run the Compute[...]

Cannot eject c ompact disc (tra y-load unit). Cause Solution Disc not properly seated in the drive. Turn off the computer and insert a thin metal r od into the emergency eject hole and push firmly. Slowly p ull the tray out from the drive until the tray is fully extended, then remove the disc. CD-ROM, CD-RW, DVD-ROM, or DVD- R/RW drive cannot read [...]

Table 8-15 Solvin g USB Flash Dr ive Proble ms USB flash drive is not se en as a drive letter in Windows. Cause Solution The drive letter after the last physical drive is no t available. Change the de fault drive letter for the flash drive in Window s. USB flas h drive not f ound (ident ified). Cause Solution The device is attached to a USB port th[...]

Solving Front Panel Component Problems If you encounte r problems with devices connecte d to the front panel, refe r to the common cau ses and solutions listed in the foll owing table. A USB device, headpho ne, or microphone is not recognized by the com puter. Cause Solution Device is not properly connected. 1. Turn off the computer. 2. Reconnect t[...]

Unable to connect to the Internet. Cause Solution IP address is not configured properly. Conta ct your ISP for the correct IP address. Cookies are corrup ted. (A “cookie” is a small piece of information that a Web server can store temporarily with the Web browser. This is useful for having the bro wser remember some specific information that th[...]

Solving Software Problems Most software problems occu r as a result of the foll owing: ● The application wa s not installed or configured co rrectly. ● There is insufficient m emory available to run the application. ● There is a conf lict between a pplications. ● Be sure that all the neede d device drivers have been insta lled. ● If you h[...]

Computer will not continue after HP logo screen disp lays. Cause Solution System files may be damaged. In Win dows 7, use recovery media to scan hard drive for errors, or use Windows Startup Repair to fix problems that might prevent Windows from starting correctly. Windows Startup Repair is one of the recovery tools in the System Recovery Options m[...]

Contacting Customer Support For help and service, conta ct an authorized reselle r or dealer. To locate a reseller or dealer near yo u, visit http://www.hp. com . NOTE: If you take the computer to an authorized reselle r, dealer, or service provider for service, remember to pro vide the setup a nd power-on passwords if they are set. Refer to the nu[...]

9 POST Error Messages This appendix lists the erro r codes, error messa g es, and the various indicator li ght and audible sequences that yo u may encounter durin g Power-On Self-Tes t (POST) or computer restart, the probable source of the problem, and steps you can take to resolve the error co ndition. POST Message Disabled suppresses most system [...]

POST Numeric Codes and Text Messages This section covers those POST errors that have numeric codes associated with them. The section also includes some text messages th at may be encoun tered during POST. NOTE: The computer will beep once after a POST text message is disp layed on the screen. Table 9-1 Numer ic Codes and Text M essages Control pane[...]

Table 9-1 Numer ic Codes and Text M essages (continued ) Control panel message Description Recommended action 163-Time & Date Not Set Invalid time or date in configuration memory. RTC (real-time clock) battery may need to be replaced. Reset the date and time under Control Panel (Computer Setup can also be used). If the problem persists, replace[...]

Table 9-1 Numer ic Codes and Text M essages (continued ) Control panel message Description Recommended action 303-Keyboard Controller Error I/O board keyboard controlle r. 1. Reconne ct keyboard with computer turn ed off. 2. Replace the system board. 304-Keyboard or System Unit Err or Keyboard failure. 1. Reconnect the keyboard with computer turn e[...]

Table 9-1 Numer ic Codes and Text M essages (continued ) Control panel message Description Recommended action 601-Diskette Controller Error Diskette controller circuitry or floppy drive circuitry incorrect. 1. Check and/or replace cables. 2. Clear CMOS. (See Appendix B, Password Security and Resetting CMOS on page 190 .) 3. Replace diskette drive. [...]

Table 9-1 Numer ic Codes and Text M essages (continued ) Control panel message Description Recommended action 1720-SMART Hard Drive Detects Imminent Failure Hard drive is about to fail. (Some hard drives have a hard drive firmwar e patch that will fix an erroneous error message .) 1. Determine if hard drive is giving correct error message. Enter Co[...]

Table 9-1 Numer ic Codes and Text M essages (continued ) Control panel message Description Recommended action 2201-MEBx Module did not checksum correctly Memory error during POST execution of the Management Engine (ME) BIOS Extensions option ROM. 1. Reboot the computer. 2. Unplug the power cord, re-seat the memory modules, and reboot the computer. [...]

Table 9-1 Numer ic Codes and Text M essages (continued ) Control panel message Description Recommended action 2211-Memory not configured correctly for proper MEBx execution. DIMM1 or XMM1 is not installed. Make sure there is a memory module in the black DIMM1 socket and that it is properly seated. 2212-USB Key Provisioning failure writing to device[...]

Table 9-1 Numer ic Codes and Text M essages (continued ) Control panel message Description Recommended action 2230-General error during MEBx execution E rror occur red during MEBx execution which fails into the “General” groupin g. Status information displayed along with the error provides further clarity into the failure. MEBx handles transfer[...]

Table 9-1 Numer ic Codes and Text M essages (continued ) Control panel message Description Recommended action Network Server Mode Active and No Keyboard Attach ed Keyboard failu re while Network Server Mode enabled. 1. Reconnect keyboard with computer turn ed off. 2. Check connector for bent or missing pins. 3. Ensure that none of the keys ar e dep[...]

Table 9-2 Diagnostic Front Panel LEDs and Audible Codes (continue d) Activity Beeps P ossible Cause Recommen ded Action Red Power LED flashes two times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 2 Processor thermal protection activated: A fan may be blocked or not [...]

Table 9-2 Diagnostic Front Panel LEDs and Audible Codes (continue d) Activity Beeps P ossible Cause Recommen ded Action Red Power LED flashes five times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 5 Pre-video memory error. CAUTION: To avoid damage to the DIMMs or th[...]

Table 9-2 Diagnostic Front Panel LEDs and Audible Codes (continue d) Activity Beeps P ossible Cause Recommen ded Action Red Power LED flashes ten times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 10 Bad option card. 1. Che ck each option card by removing the card (o[...]

10 Password Security and Resetting CMOS This computer supports security password featur es, which ca n be established through the Comput er Setup Utilities menu. This computer supports two se curity password fe atures that are e stablished through the Co mputer Setup Utilities menu : setup password a nd power-on password. When yo u establish on ly [...]

Resetting the Password Jumper CAUTION: If you enable the stringent security feature in Computer Setup and you forget the setup password or the power-on pa ssword, the c omputer is inaccessib le and can no lo nger be used. Enabling the stringent password dis ables the ability to reset the pa ssword by moving the jumper on the system board. If you lo[...]

Clearing and Resetting the CMOS The computer’s configuratio n memory (CMOS) stores information about the computer’s configuration. The CMOS bu tton resets CMOS but doe s no t cl ear the power-on and setup passwords. Clearing CMOS wi ll clear the Active Manage ment Technology (AMT) settings in the Manag ement Engine BIOS Extension (MEBx), includ[...]

4. Locate, press, and hold the CMOS button in for five se conds. NOTE: Make sure you have disconn ected the AC power cord fr om the wall outlet. The CMOS button will not clear CMO S if the power cord is connected. Figure 10-1 CMOS button NOTE: For assistan ce locating the CMOS butto n and other system boa rd components, see the Illustrated Parts &a[...]

11 HP PC Hardware Diagnostics To help troubl eshoot and diagno se failures, use th e UEFI-based hardware diagno stic solution that HP includes on all pro ducts. This tool can even be used if the computer will not boot to the operating system. Why run HP PC Hardware Diagnostics – UEFI The HP PC Hardware Diagnostic tools simp lify the process of di[...]

After pressing F2 , the BIOS sequentially searc hes th ree places for the system diagnostics: a. First – a connected USB drive (to download the di agnostics tools to a USB drive, see the instructions in Downloading HP PC Hardware Diagnostics to a USB device on page 195 ). b. Second – the hard disk d rive. c. Third – in the BIOS, a core set of[...]

12 Backup and Recovery Restoring and recovering in Windows 7 To protect from loss or damage, back up your person al data files. Refer to the operating system or backup utility documentation for instructions on making backup copies of your data files. To protect th e software from loss or damage, keep a backup copy of all system software, applicatio[...]

System Recovery completely e rases and reformat s th e hard disk drive, deleting all data fi les that you have created, and th en reinstal ls the operating system, p rograms, and drivers. However, yo u must reinstall any softw are that was not inst alled on the co mputer at the factory. This includes software that came on media in cluded in the com[...]

8. System Recovery begins. After Syst em Recovery is complete, click Fini sh to restart the computer. 9. When Windo ws has loaded, shut do wn the comput er, reconnect all perip heral devices, and then turn the computer ba ck on. System Recovery when Wi ndows is not respondin g CAUTION: System Recovery deletes all data and programs you create d or i[...]

● If you are creating recovery discs, be sure to use high-quality discs. It is normal for the system t o reject defective discs. You will be prompted to insert a new blank disc to try again. ● The number of discs in the reco very-disc set depends on your co mputer model (typica lly 3 to 6 DVDs). The Recovery Media Crea tion program tells you th[...]

Using recovery media CAUTION: System Recovery deletes all data and progra ms you have created o r installed. Back up any important data to a CD or DVD or to a USB flash drive. To create recovery m edia, see System recovery usin g recovery media on pa ge 198 . To perform a System Recovery using recovery media: 1. If using a set of D VDs, insert the [...]

Backup and recovery in Windows 8 To protect you r information, use Windows Backup and Restor e to back up individu al files and folder s, back up your entire hard drive, crea te system repair media, or create system restore points. In case of system failure, you can use the backup file s to restore the contents of yo ur computer. From the Start s c[...]

Performing a system recovery In case of system failure or inst ability, the computer provides the following tools to recover your files: ● Windows recovery to ols: You can use Windo ws Backup and Restor e to recover inform ation you have previously backed up . You can also u se Wi ndows Automatic Re pair to fix problems th at might prevent Window[...]

Using f11 recovery tools CAUTION: Using f11 complete ly erases hard dr ive contents and reformats the hard drive. Al l files that you have created and any software that yo u have installed on th e computer are permanen tly removed. The f11 recovery tool reinstalls the operatin g system and HP programs and drivers that were installed at the fa ctory[...]

A Battery Replacement The battery that comes with the comp uter provides power to th e real-time clock. When repla cing the battery, use a b attery equivale nt to the battery or iginally installed in t he computer. The co mputer comes with a 3-volt lithium coin cell battery. WARNING! The computer contains an in ternal lithium ma nganese dioxide bat[...]

7. Depending on the type of battery holder on the system board, comp lete the following instructions to replace the b attery. Type 1 a. Lift the bat tery out of it s holder. Figure A-1 Removing a Coin Cell Battery (Type 1) b. Slide the replacement batte ry into position, positive side up. The battery holder automatically secures the battery in the [...]

b. Insert the new battery an d position the clip back in to place. Figure A-3 Removing a Coin Cell Battery (Type 3) NOTE: After the batter y has been replace d, use the following steps to complete this proced ure. 8. Replace the computer access p anel. 9. Plug in the comput er and turn on power to the computer. 10. Reset the date and time, your pas[...]

B Removing and Replacing a Removable 3.5-inch SATA Hard Drive Some models are equ ipped with a Removable SAT A Hard Drive Enclos ure in the 5.25-inch i nternal drive bay. The hard dr ive is housed in a carr ier that can be quickly a nd easily removed from th e drive bay. To remove and replace a drive in the carrier: NOTE: Before you remove th e old[...]

3. Remove the adhesive strip that secures the th ermal sensor to the to p of the hard drive (1) and move the thermal se nsor away from the ca rrier (2) . Figure B-2 Removi ng the Therma l Sensor 4. Remove the four screws from the bot tom of the hard drive ca rrier. Figure B-3 Remo ving the Se curity Screws 208 Appendix B Removing and Replacing a Re[...]

5. Slide the hard drive back to disconnect it from the carr ier then l ift it up a nd out of the carri er. Figure B-4 Re moving the Ha rd Drive 6. Place the new hard drive in the carrier th en slide th e hard drive back so th at it seats in the SATA connector on the carri er's circuit board. Be sure the connector on the hard drive is pressed a[...]

7. Replace the four screws in the bottom of the carrier to hold the drive securely in place. Figure B-6 Replacing the Security Screws 8. Place the thermal sensor o n top of the hard driv e in a position that does not co ver the label (1) and attach th e thermal sensor to the top of the hard drive with the adhesive strip (2) . Figure B-7 Replacing t[...]

9. Slide the cover on the carrier (1) and replace the screw on the rear of the carrier to secure the cover in place (2) . Figure B-8 Replacing the Carrier Co ver 10. Slide the h ard drive c arrier into t he enclosur e on the computer and lock it with the key provided. NOTE: The carrier must be l ocked for power to be supplied to the hard d rive. 21[...]

C Unlocking the Smart Cover Lock NOTE: The Smart Cover Lock is an optional feature in cluded on some m odels only. The Smart Cover Lock is a software-controllable cover lock, controlled by the setup password. This lock prevents una uthorized access to the in ternal compo nents. The computer ships wi th the Smart Cover Lock in the unl ocked position[...]

Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock To open the access pane l with the Smart Cover Lock engaged: 1. Prepare the computer for disassembly. 2. Use the Sma rt Cover FailSafe K ey to remo ve the two tampe r-proof screws that secure the Smart Cover Lock to the chassis. Figure C -1 Removing the Sma rt Cover Lock Screws fro m[...]

Figure C -3 Removing the Smart Cover Lock Screws from the Small Form Factor You can now re move the access panel. To reattach the Smart Cover Lo ck, secure the lock in place with the tamper-proof screws. 214 Appendix C Unlocking the Smart Co ver Lock[...]

D Power Cord Set Requirements The power supplies o n some computers have exte rnal power switches. The voltage select switch feature on the co mputer permits it to operate from any line voltage between 100-120 o r 220-240 volts AC. Power supplies on those computers that do n ot have extern al power switches are equipped with internal switches that [...]

Country-Specific Requirements Additional requi rements specific to a country are sh own in parentheses an d explained below. Country Accrediting Agency Country Accrediting Age ncy Australia (1) Austria (1) Belgium (1) Canada (2) EANSW OVE CEBC CSA Italy (1) Japan (3) Norway (1) Sweden (1) IMQ METI NEMKO SEMKO Denmark (1) Finland (1) France (1) Germ[...]

E Specifications MT Specifications Table E-1 Sp ecifica tions Chassis Height Width Depth 14.9 in 7.0 in 17.0 in 37.7 cm 17.7 cm 43.1 cm Approximate Weight 20.5 lb 9.3 kg Weight Supported (maximum distributed load in desktop position) 77 lb 35 kg Temperature Ra nge Operating Nonoperating 50° to 95°F -22° to 140°F 10° to 35°C -30° to 60°C NOT[...]

Table E-1 Spec ificat ions (contin ued) Standard Efficiency High Efficiency 320W 320W active PFC; 87/90/87% e fficient at 20/50/100% load Rated Input Current 5.5A 1 This system utilizes an active power fa ctor corrected power supply. Th is allows the system to pass the CE mark requirements for use in the countries of the Eur opean Union. The active[...]

SFF Specifications Table E-2 Sp ecifica tions Chassis (in the desktop position) Height Width Depth 4.0 in 13.3 in 14.9 in 10.0 cm 33.8 cm 37.9 cm Approximate Weight 16.7 lb 7.6 kg Weight Supported (maximum distributed load in desktop position) 77 lb 35 kg Temperature Ra nge Operating Nonoperating 50° to 95 °F -22° to 140° F 10° to 35 °C -30°[...]

Index Symbols/Numerics 2.5-in drive adapter, spare part number 29, 39 A access panel locking and unlocking 212 MT removal 55 MT spare part number 55 SFF removal and replacement 95 SFF spare part number 95 access panel, locke d 140 access panel, MT spare part number 26, 32 access panel, SFF spare part number 35, 42 adapter, DisplayPor t to DVI spare[...]

eSATA port (expansion), spar e part number 32, 42 eSATA port assembly, spare part number 29, 39 expansion card MT installation 63 MT removal 63 SFF installation 103 SFF removal 103 expansion slot cover MT removal 64 SFF removal 104 external USB webcam, spare part number 29, 39 F f11 recovery 203 FailSafe Key 212 fan MT spare part number 89 fan duct[...]

keyboard problems 159 L LEDs blinking power 186 blinking PS/2 keyboard 186 locks MT front bezel 57 SFF front bezel 97 Smart Cover Lock 212 M media card reader MT installation 72 MT removal 71 SFF installation 115 SFF removal 114 Media Card Read er problems 148 memory MT installation 60 MT socket population 60 MT specificat ions 60 SFF installation [...]

monitor 150 mouse 159 network 163 power 143 printer 157 processor 168 software 174 processor MT removal and replacem ent 85 SFF removal and replacement 128 spare part number 26, 32, 33, 36, 42, 43 processor problems 168 product ID locations 6 R rear chassis fan MT removal and replacem ent 89 MT spare part number 89 rear panel components MT 4 SFF 5 [...]

system board removal and replacement 133 system board, spare part number 35, 43 Smart Cover Lock 212 software problems 174 servicing computer 50 solenoid lock spare part number 28, 32, 42 solenoid lock, SFF spare part number 38 solid-state drive, spare part number 30, 40 spare part numb er tamper-resistant wrench 50 Torx T-15 screw driver 50 speake[...]