Hunter Fan 22360 инструкция обслуживания

Hunter F an Company 42704-01 • 01/29/07 For Y our Records and Warranty Assistance Model Name: _____________________ Catalog/Mo del No.: ________________ Serial No.: ________________________ Date P urchased: ___________________ Where P urc hase d: _________________ For refer ence also attach your receipt or a copy of your receipt to the manual.[...]

Hunter F an Company 42704-01 • 01/29/07 2 Welcome T able of Contents 1 • W elcome . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 • Optional Accessories . . . . . . . . . . . . . . . . . . . 3 3 • Getting Ready . . . . . . . . . . . . . . . . . . . . . . . 4 4 • Pre-Installa tion . . . . . . . . . . . . . . . . . . . . . . . 5 5 ?[...]

Hunter F an Company 42704-01 • 01/29/07 3 Optional Accessories Understanding Mounting Hunter’ s patented mount ing system pr ovides you maximum eas e in installing your fan.  i s fan was designed to be mounted only on fl at ceilings and c an be us ed only on ceilings no less than 9 feet high. Considering Optional Accessories Consider using [...]

Hunter F an Company 42704-01 • 01/29/07 T o install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or ot her suitable suppor t in ceiling . • Drill holes for and install woo d screws. • Ident if y and connect ele ctrical wires. • Lift 40 p ounds . If you need help installing the fan, your Hunter fan dealer can[...]

Hunter F an Company 42704-01 • 01/29/07 ! ! 5 Pre-Installation Pre- Installation Selec t installation sit e: Normally this is near the cent er of the r oom, often r eplacing a light fi xture. Make certain that ample clearance is left for t he rotat ing fan blades . For maximum effi cienc y , no obstruction (walls, po sts , etc.) should be within[...]

Hunter F an Company 42704-01 • 01/29/07 6 Installing Ceiling Hardware Fig. 2 3 1/2” Lag Bolt CA UTION DO NOT USE LUBRICANT ON SCREWS ! ! 1. Drill (2) 11/64” diameter holes t hrough t he outermost holes in t he box 2” deep into t he cross brace.  es e holes are for the U-brack et bolts . Install rubber bushing and pin into the u-brack et.[...]

Hunter F an Company 42704-01 • 01/29/07 Motor Housing Hanger Pip e Wires Motor Housing Se t Sc r ew Canopy CA UTION BE SURE TO TIGHTEN THE HANGER PI PE INT O THE F AN , AND TH E HANGER BR ACKET ON T O THE PIPE. TIGHTEN THE 2 SET SCREWS , A S DES CRIBED IN STEP 7, T O PREVENT THE F AN FROM F ALLING . YOUR F AN MA Y WEIGH UP T O 50 LBS . ALL OF THE[...]

Hunter F an Company 42704-01 • 01/29/07 8 Hanging The Fan 5. Back out the set s crew on the hanger brack et . 6. Feed the 3 wires through t he hanger bracke t assembly and s crew the hanger brack et ont o the hanger pipe until tigh t (at least 3 t urns) (see Fig , 6). 7. Use pliers to tighte n both the hanger bracket assembly and the hanger pipe [...]

Hunter F an Company 42704-01 • 01/29/07 CA UTION BE CERT AIN THA T THE ELECTRI CITY IS TURNED OFF A T THE MAIN P ANEL BEFORE ST ARTING THIS SECTION. ! ! CA UTION NO BA RE WIRES OR WIRE ST R ANDS SHOULD BE VISIBLE AFTER M AKING C ONNECTIONS. ! ! 9 Wiring the Fan NO TE: All wiring must be in accordance with national and local elec trical codes and [...]

Hunter F an Company 42704-01 • 01/29/07 10 Installing The Canopy 1. Partially install the fi llister head #8-32 set screw . 2.. Slide canopy up close to ceiling. 3. Tigh ten t he canopy fi llister head #8-32 set screw (see Fig . 11). Fig. 11 Screw , Fillister Head #8-32 Canop y Scr ew , Filliste r Head #8-32[...]

Hunter F an Company 42704-01 • 01/29/07 11 Lubrication Adding Oil 1. Y our fan has b een shippe d without oil in the motor . 2. A 1-ounce tube of high grade SAE 10 non-deter gent oil i s packaged in the s ack par ts . 3. All of the oil in the tube must be put into the fan. 4. Cut t he tip off the end of the t ube and place the tube into t he oil[...]

Hunter F an Company 42704-01 • 01/29/07 Fig. 15 Installation Of Fan Blade Assembly 1. Loos en the blade assembly screw , but do not remove. 2. Align the blade blase a ssembly s crew with t h e Adapt Air blade shaft counter sink (see Fig . 14). 3. Slide the blade assembly onto the Adapt Air blade shaft. (se e Fig . 15). 4. Be fore t ighte ning the[...]

Hunter F an Company 42704-01 • 01/29/07 Fig. 16 13 Installing Bulb And Globe 1. Make sure the fan and light circ uits are off b efore installing the 19 watt CFL (C ompact Fluorescent Light) bulb. 2. Inser t and screw the CFL bulb into t he light so cket t urning the CFL bulb clo ckwise (s ee. Fig . 16). 19 W att CFL Bulb Light So cket 4. Slide t[...]

Hunter F an Company 42704-01 • 01/29/07 Fig. 19 Directional Lever UP DO W N 14 Operation And Care 1.  e f an pull chain contr ols power to the fan.  e pull chain ha s four settings in s equence: High, Medium, Low and Off . • Pull the chain slowly t o change settings . • Release slowly to preven t the chain from r ecoiling into t he bla[...]

Hunter F an Company 42704-01 • 01/29/07 15 Troubleshooting Guide Problem: Nothing happens; fan does not move. 1. T urn power on, re place fus e, or reset break er . 2. Check all connec tions accor ding to the wiring t he fan se ction. 3. Pull the pull chain to e nsure it i s on. Problem: Noisy operation. 1. Tigh te n the blade assembly screws unt[...]

Hunter F an Company 42704-01 • 01/29/07 16 Notes[...]

©2007 HUNTER F AN CO .™ HUNTER F AN COMP ANY 2500 FRISCO A VENUE MEMPHIS, TN 38114[...]