Hunter Fan 43168 инструкция обслуживания

1 Model 43168 Owners Manual HEA T PUMP PROGRAMMABLE THERMOST A T PM COOL TEM P 3 SA Form 44014-01 r010408[...]

2 3 Congratulations! Thank you for choosing a Climate T echnology Corporation (CTC) programmable thermostat. Y our new CTC thermostat will provide years of reliable service and year-round energy savings. Please read this manual before beginning installation and save this booklet for complete operation instructions. The CTC T echnical Support Group [...]

4 5 1.This thermostat is designed to work on the following systems: • Single-Stage Heat Pump • Mulit-stage Heat Pump (up to 2 heating and 2 cooling) 2.T emperature Range This thermostat can be set between 45°F and 95°F (7°C and 35°C).However , it will display room temperatures from 30°F to 99°F (0°C and 37°C). “HI” will be dis[...]

6 7 Wire Labeling • CAUTION! TURN OFF POWER TO THE HEA T PUMP SYSTEM BEFORE YOU A TTEMPT TO ACCESS THE THERMOST A T’S WIRING. • IMPORT ANT! BEFORE DISCONNECTING ANY WIRES FROM THE EXISTING THERMOST A T , APPL Y THE PROVIDED SELF-ADHESIVE LABELS TO THE WIRES. • Use the information in T able 1 below and the[...]

8 9 Mount Wallplate • Remove the wallplate from the thermostat by pressing the release tab on the bottom of the thermostat. See Figure 2. Figure 2 • Positionwallplateonwall andpullexisting wiresthroughthelarge opening,thenlevelfor appearance.If the existing mounting holes from the old wal[...]

10 11 ON O N 1 2 HE HG F C Connect Wires and Mount Thermostat to W allplate • Match and connect the labeled wires to the appropriate coded terminal screws on the wallplate. See Figure 4. Ignore any wires which may be present, but which were not connected to the old thermostat. R Figure 4 T erminal Screws • Be sure to tighten the terminal [...]

12 13 THERMOST A T CONTROLS • Open the thermostat’s front cover . See Figure 6. Figure 6 • Insertthetabsontopofthethermostatbodyintotheslotsatthetopofthewallplate.Pressthebottomof the thermostat body into the snap on the bottom of the wallplate. ( NOTE :Do notfor[...]

14 15 system off cool heat fan auto refresh on reset hold/rtrn em heat sys em aux lter program day/time A B C D E I J K Switches and Buttons Switches and Buttons A LCD Readout - displays indoor temperature, set temperature, and information about the heat pump system’s operation and status. B System Switch -“emheat”istheEm[...]

16 17 The default for this thermostat setting is in a 12 hour format. Y ou can change the format to 24 hour format by pressing D a y /T i m e and then P r o g r a m . The AM/PM indicator will be off when the thermostat is in 24 hour mode. Settingdayandtime: 1. Press D a y /T i m e .(AM/PMandcurrenthourwillash) Press U [...]

18 19 This thermostat gives you the ability to program up to 4 custom temperature settings per day or utilize pre-programmed settings. For manual operation instructions, see pages 21-23. T o utilize the pre-programmed settings, see pages 24-25. T o create custom programs, see pages 26-29. Methods of Operation AM HE AT 4[...]

20 21 1. MANUAL OPERA TION Many people prefer to operate their thermostats manually , adjusting settings as needed. Y ou can either temporarily override the settings for the current program, or permanently override all settings and adjust temperatures manually . Ifyouwanttoonlytemporarilyoverridethecurrentprogram: 1. Pres[...]

22 23 MANUAL OPERA TION, CONT . Ifyouwanttopermanentlyoverrideallsettingsandadjustthethermostatmanually: 1. Press H o l D /r e T U r n until the Hold icon appears. 2. Press and hold U P or D o w n for one second to enter Manual Override mode. (Release the buttonwhenthedisplayashes.) 3. Press the U [...]

24 25 2. DEF AUL T PROGRAMS ThisthermostatmeetsENERGYST ARguidelinesforenergyefciency .Byusingthepre- programmed settings, this thermostat can save you money by optimizing energy usage in heating and cooling. Refer to the Default Programs Chart on page 24 for detailed information about the pre- programmed s[...]

26 27 system off cool heat hold/rtrn em heat program Methods of Operation (cont.) AM PM H o l D /r e T U r n P r o g r a m U P and D o w n buttons s y s T e m switch AM/PM indicator 3. CREA TING CUSTOM PROGRAMS NOTES: • Programtimescanbesetin10minuteincrements. • Programtemperaturecanbesetinincrem[...]

28 29 Methods of Operation (cont.) system off cool heat em heat program AM HE AT PM COOL 4 3 2 1 M T W TH F SA SU 3. Press U P or D o w n to change the hour . Press P r o g r a m to save the hour and adjust the minute setting. 4. Press U P or D o w n to change the minute. Press P r o g r a m to save the minute setting and adjust the temperature. 5.[...]

30 31 1. INDIGLO ® night-light - will backlight the display for easy viewing in the dark. Press any button to illuminate the light. 2. Filterchangeindicator-willashafter400hoursofsystemuseasaremindertocheckor changeyourlter .Pressandholdthe F i l T e r button[...]

32 33 6. Error mode – if the thermostat is unable to control your system due to an unexpected problem,thethermostatwillenterErrorMode.Inthiscondition,thethermostatashes“E1”, “E2”, or “E3” on the LCD display , and shuts off your system. 7. Auto cut off – automatically turns the system off [...]

34 35 1. T emperature Range 2. Compressor Protection After the system stops running, there will be a 3.5 minute delay before it can be restarted to prevent compressor damage due to rapid cycling. 3. Resetting the unit T o restore the thermostat to the original factory settings, press the reset button with a paperclip. (This will erase any user-prog[...]

36 37 Setting Options ThefollowingOptionsareavailableonyourthermostat: 1. 1st stage span - The factory setting for Stage 1 heating and cooling is 1, meaning that your thermostat will cycle at 1°F (0.5°C) above and below the set temperature in Stage 1. If the system is cycling too fast or too slow , then the Span can be adjust[...]

38 39 TROUBLESHOOTING Problem Solution 1. Check wiring connections. A Common (C) wire is required for operation. 2. Press and hold the Reset button for two seconds with the tip of a paper clip. LCD Display is blank Auto/Fan does not turn on in Heat Mode 1. Move the #1 System Set-Up Switch (HG/HE) to the opposite position. Fan runs continuously 1. C[...]

40 41 WIRING DIAGRAM[...]