Hunter Fan 53115 инструкция обслуживания

www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 10 PA G E 5 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Wiring C anopy Downrod PA G E 6 Prepar ation T able of C ontents PA G E 11 Mounting Options PA G E 13 PA G E 14 Blades Swit ch Housing Light Kit PA G E 12 PA G E 4 Congratulat[...]

www .HunterF an.com 1.888.830.1326 M0069-01 • 04/30/13 • © Hunter F an Company What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you. Check box to see fan weight Assess location 30 inches from blade tip to nearest wall or obstruction 7 feet [...]

T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools . www .HunterF an.com 1.888.830.1326 3 M0069-01 • 04/30/13 • © Hunter F an Company[...]

www .HunterF an.com 1.888.830.1326 4 M0069-01 • 04/30/13 • © Hunter F an Company 4 If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) . Guide T ouches BOTH Ceiling & Wa ll S I T U A T I O N 1 Guide[...]

1.888.830.1326 www .HunterF an.com C eiling Bracket OFF Make sure all four (4) bumpers are still attached . F or angled ceilings, point opening toward peak. Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the [...]

www .HunterF an.com 1.888.830.1326 C eiling Bracket (c ontinued) Prepar ation 1.888.830.1326 www .HunterF an.com D I S C A R D K E E P ! Remove the shipping blocks from the motor . Sav e the screws . They will be needed for blade iron installation. Note: Some fans will hav e a shipping ring instead of shipping blocks. Please remove the ring and sa [...]

1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a diff erent downrod length follo w these steps: Ste[...]

KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od. Downrod (c ontinued) 8” 3/8” Tighten the setscrew with pliers. DO [...]

1.888.830.1326 9 M0069-01 • 04/30/13 • © Hunter F an Company www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan.[...]

www .HunterF an.com 1.888.830.1326 Wiring T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x. Refer to CA UTION c.1 on pg. 2 F R O M R E C E I V E R F R O M C [...]

www .HunterF an.com 1.888.830.1326 11 M0069-01 • 04/30/13 • © Hunter F an Company Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardwar e bag. No te: Fan sty[...]

www .HunterF an.com 1.888.830.1326 M0069-01 • 04/30/13 • © Hunter F an Company Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes. 12 Insert grommets found in the hardware bag i[...]

www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfwa y into the motor housing . I t does not matter which two screw holes you choose . Insert the third screw[...]

www .HunterF an.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the bag . Align the notches in the sides of the lower switch housing with the screws on the upper switch housing . T wist the lower [...]

www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) Install a light bulb in each socket. Note: Do not use CFL bulbs to replace your light bulbs . Y our lights may icker or fail to work. No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions. Connect the appropriate pull chain pendant to eac[...]

www .HunterF an.com 1.888.830.1326 Remote C ontrol ON T urn P ow er Note: The remote must be pair ed before the fan will operate . Within 3 minutes of rest oring power to the fan, press both the F an Off button and the High button for at least 4 seconds . Y our fan will turn on low to indicate successful syncing. If it does not, turn off po wer to [...]

www .HunterF an.com 1.888.830.1326 Remote C ontrol (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! Push the light button on the r emote transmitter . Pull the light chain once . If the light does not turn on, repeat step . Push the 3 button on the r emote transmitter for high fan speed. P ull the fan speed chain until the fan is on the highest spe[...]

www .HunterF an.com 1.888.830.1326 Rocker- Style Plate Switch C over Plate Removed T abs T o install the transmitter cradle, remo ve the two screws holding the switch c over plate. Do not remov e the cover plate. Orient the cr adle by lining up the two mounting holes with those on the cov er plate. Inser t and tighten the screws. Do not ov er tight[...]

www .HunterF an.com 1.888.830.1326 M0069-01 • 04/30/13 • © Hunter F an Company 19 F or cleaning the fan, use sof t brushes or cloths to prevent scr atching. Cleaning products may damage the nishes. Safe-Exit • Press the F an O ff button for at least three sec onds to initiate the Safe-Exit Mode . • The lights will ash for visual c on[...]

www .HunterF an.com 1.888.830.1326 M0069-01 • 04/30/13 • © Hunter F an Company 20 T roubleshooting Lights dim when turned on or do not turn on at all. • Make sure the wattage of the light bulbs installed matches the specications on the light sockets. F an doesn’ t work • Make sure power switch is on. • Pull the pull chain to make su[...]