Hunter Fan 54015 инструкция обслуживания

www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 13 PA G E 10 PA G E 5 PA G E 6 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Wiring C anopy Operation,Main tenance & Cleaning Blades T roubleshooting Downrod Swit ch Housing Prepar ation T able of C ontents PA G E 11 PA G E 12 PA[...]

www .HunterF an.com 1.888.830.1326 M0074-01 • 05/14/14 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring , use a qualied electrician. Y ou may need a friend to help you . Check box to see fan weight Assess location 30 inches from blade tip to nea[...]

www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools . 3 M0074-01 • 05/14/14 • © Hunter F an Company[...]

www .HunterF an.com 1.888.830.1326 4 M0074-01 • 05/14/14 • © Hunter F an Company 1.866.268.1936 If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) . Guide T ouches BOTH Ceiling & Wa ll S I T U A T [...]

www .HunterF an.com 1.888.830.1326 1.888.830.1326 www .HunterF an.com C eiling Bracket 5 Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. F or angled ceilings, point opening toward pea[...]

www .HunterF an.com 1.888.830.1326 1.888.830.1326 www .HunterF an.com Prepar ation D I S C A R D K E E P ! Remove the shipping blocks fr om the motor . Sav e the screws . They will be needed for blade iron installation. Note: Some fans will hav e a shipping ring instead of shipping blocks. Please remov e the ring and save the screws. Time Sav er Ti[...]

1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a diff erent downrod length follo w these steps: Ste[...]

KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od. Downrod (c ontinued) 8” 3/8” Tighten the setscrew with pliers. DO [...]

1.888.830.1326 9 M0074-01 • 05/14/14 • © Hunter F an Company www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan.[...]

www .HunterF an.com 1.888.830.1326 Wiring T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x. Refer to CA UTION c.1 on pg. 2 Using an orange wire connector fro[...]

www .HunterF an.com 1.888.830.1326 11 M0074-01 • 05/14/14 • © Hunter F an Company Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardwar e bag. No te: Fan sty[...]

www .HunterF an.com 1.888.830.1326 M0074-01 • 05/14/14 • © Hunter F an Company Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes. 12 Insert grommets found in the hardware bag i[...]

www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two housing assembly screws from the hardware bag halfwa y into the motor housing . I t does not matter which two screw holes you choose . Insert the third screw , f[...]

www .HunterF an.com 1.888.830.1326 S witch Housing (continued) Make sure the lower switch housing is securely attached to the upper switch housing. F ailure to properly secur e all three assembly screws could result in the switch housing falling . Connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored marking[...]

www .HunterF an.com 1.888.830.1326 Within 3 minutes of rest oring power to the fan, press both the F an Off button and the High button f or at least 4 seconds. Y our fan will turn on low to indicate succ essful syncing. If it does not, turn off power to y our fan, wait 1 minute then try again. If using the transmitter with multiple fans, repeat thi[...]

www .HunterF an.com 1.888.830.1326 16 M0074-01 • 05/14/14 • © Hunter F an Company 16 F or cleaning the fan, use sof t brushes or cloths to prevent scr atching. Cleaning products may damage the nishes. Opera tion, Maintenance , & Cleaning (con tinued) Reverse Switch T o switch the direc tion of air ow , mov e the reverse switch t o th[...]

www .HunterF an.com 1.888.830.1326 M0074-01 • 05/14/14 • © Hunter F an Company 17 T roubleshooting F an doesn’ t work • Make sure power switch is on. • Pull the pull chain to make sure it is on. • Push the motor r eversing switch rmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is tu[...]