Hunter Fan MD506-01 инструкция обслуживания

www .ventiladoreshunt er .com.br MD506-01 • 09/19/14 • © Hunter F an Company ENGLISH[...]

Impor tant Instruc tions: Keep Instruc tions f or future use[...]

1 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company What to Expect with Y our Installation PA G E 5 Ceiling Br acket T able of C ontents PA G E 19 T roubleshooting ? ? ? PA G E 20 W arranty Sta tement Mounting Options PA G E 4 Congratulations on purchasing y our new Hunter® ceiling fan! It will provide comfort and per formanc[...]

www .hunter fan.com.br 2 MD506-01 • 09/19/14 • © Hunter F an Company What t o Expec t with Y our Installation w .1 - T o reduce the risk of re , elec trical shock, or personal injury , mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 31.8 kg and use the mounting screws provided with the ou[...]

www .hunter fan.com.br T ools Needed Ladder Pliers Wire Strippers Screwdrivers P ower Drill (optional) 3.5 mm Drill Bit (optional) 8 mm Drill Bit (optional) If mounting to a support structure, you will also need these tools. Hammer (optional) 3 MD506-01 • 09/19/14 • © Hunter F an Company[...]

www .hunter fan.com.br Hang your fan by a standard do wnrod (included) or use a shorter downrod ( sold separately ) f or Low-Prole Mounting . Mounting Options C eiling Bracket Note: Do not hang the fan from a ceiling that is angled greater than 34 ° Support Structure Ceiling Outlet Box (required) Angled Mounting Style Standard Mounting Style Su[...]

5 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company C eiling Bracket (c ontinued) Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Use wood scr ews (included) whe[...]

6 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Assembling the T op Housing KEEP! Remove the pre-installed setscrew so that the downrod can be inserted. K E E P ! Install three upper motor cov er screws, found in the hardware bag , and tighten them securely . Upper Motor Cov er Screw T o assemble the housing t o the hanger[...]

7 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Downrod S lide S lide 1 2 3 4 5 6 7 8 9 10 Sold Separately Longer Downrod for angled ceilings or ceilings 3 m or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for c eilings 2,4-3 m high Option 1 Option 2 Option 3 skip to next page If you need a d[...]

8 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company 20 cm 1 cm C U T & S T R I P (not to scale) The wires can be cut, but lea ve at least 20 cm extending from the top of the downrod . Downrod (c ontinued) If the setscrew is not tightened securely , the fan may fall. 20 cm 1 cm Hand tighten the downrod (at least 4-5 full tu[...]

9 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball int o the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canopy sit loosely on t op of the fan.[...]

10 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Wiring T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x. Refer to CA UTION c.1 on [...]

11 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Canop y No te: Fan style may vary. Lift the canopy into place so that the screw holes are aligned . Position the canopy so that, when lifted into place , the canopy ts into the hanging bracket as shown. Insert the two canopy screws found in the hardware bag . Screw Holes[...]

12 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Blades Y our blades ar e shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents may damage the nishes. Attach the blade to the motor using the at washers f[...]

13 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Light Kit Align the keyholes in the light k it with the two partially installed screws and turn the light kit clockwise until the screws are in the narrow ends of the keyholes. Thread the 9-pin plug connector from the fan through the light kit. Attachment Screw Partially ins[...]

14 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Light Kit (c ontinued) Make sure the light kit is securely attached to the mounting plate. F ailure to properly secure all thr ee assembly screws could result in the light xture falling. Thread the 2-pin connector through the wire slot in the the switch housing . Wire Slo[...]

15 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Light Kit (c ontinued) Connect the the 2-pin plugs from the switch housing and the LED assembly . Push ex cess wiring into the switch housing through the wire slot. Align the two screw screw holes and install the switch housing assembly screws, f ound in the hardware bag . W[...]

16 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company C ONGRA TULA TIONS! Y OU’RE DONE! See next page for fan opera tion instruc tions. Glass Globe T rim Ring Globe Assembly Screw Light Kit (c ontinued) Place the glass globe into the globe trim ring . Align the three holes in the trim ring with the three holes in the light ki[...]

17 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company Remote C ontrol Within 3 minutes of rest oring power to the fan, press both the F an Off button and the High button f or at least 4 seconds. Y our fan will turn on low to indicate succ essful syncing. If it does not, turn off power to y our fan, wait 1 minute then try again.[...]

18 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company F or cleaning the fan, use sof t brushes or cloths to prevent scr atching. Cleaning products may damage the nishes. Opera tion, Maintenance , & Cleaning T o swit ch the direc tion of air ow , remov e the globe on the fan by removing the globe assembly screws, the g[...]

19 www .hunter fan.com.br MD506-01 • 09/19/14 • © Hunter F an Company T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , suppor t the fan carefully , and check that the hanger ball is properly seated . Noisy Operation • Tighten the blade and blade iron screw[...]

www .hunter fan.com.br W ARRANT Y ST A TEMENT I - TERM AND PROOF OF W ARRANT Y 1. Hunter Ceiling F ans are warranted by Hunter F an do Brasil for a period of 1 (one) y ear from the date of purchase by the rst consumer , this being: • 3 (three) months of statutory warranty ; and • 9 (nine) months of contractual warranty provided by Hunter F a[...]