Husqvarna 1152450-26 инструкция обслуживания

E E E E n n n n g g g g l l l l i i i i s s s s h h h h K3000 K3000 W et Oper ator ′ s manual Please read the operator’ s manual car efully and mak e sure y ou understand the instructions before using the machine.[...]

2 – English KEY T O SYMBOLS Symbols on the machine: W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear: • Approv[...]

English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’ s manual: ............................... 2 CONTENTS Contents ...................................................................... 3 WHA T IS WHA T? What is what on the power cutter - K3000? ..........[...]

4 – English WHA T IS WHA T? What is what on the power cutter - K3000? 1 2 3 4 5 6 7 8 10 11 12 14 15 9 6 13 1 Rear handle 2 Guard f or the blade 14” 3 Cutting blade 4 Locking the axle 5 F ront handle 6 Inspection cov ers 7 P ower s witch lock 8 Switch 9 Rating plate 10 Brush retainer 11 Carbon brushes 12 Guard f or the blade 12” (Model versio[...]

English – 5 WHA T IS WHA T? What is what on the power cutter - K3000 W et? 1 Rear handle 2 Guard f or the blade 3 W ater kit 4 Cutting blade 5 Locking the axle 6 F ront handle 7 Inspection cov ers 8 P ower s witch lock 9 Switch 10 W ater tap 11 W ater connection with flow limiter 12 Rating plate 13 Brush retainer 14 Carbon brushes 15 Ground f au[...]

6 – English SAFETY INSTR UCTIONS Steps before using a ne w power cutter • Please read the operator’ s manual carefully and make sure you understand the instructions bef ore using the machine. • The machine is only designed f or cutting hard materials, such as concrete, brick, masonry as well as cast iron and cement pipes. • Let your Husqv[...]

English – 7 SAFETY INSTR UCTIONS General safety warnings Sav e all warnings and instructions for future ref erence. The term ”power tool” in the warnings refers to y our mains- operated (corded) pow er tool or batter y-operated (cordless) power tool. W ork area safety • K eep work area clean and well lit. Cluttered or dark areas invite acci[...]

8 – English SAFETY INSTR UCTIONS P ersonal saf ety • Sta y aler t, watch what you are doing and use common sense when operaing a pow er tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating pow er tools may result in serious personal injur y . • Use p[...]

English – 9 SAFETY INSTR UCTIONS Machine ′′ ′ ′ s safety equipment This section describes the machine ′ s safety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine . Switch T[...]

10 – English SAFETY INSTR UCTIONS Cutting blades General • Cutting blades are a vailab le in two basic designs; abrasiv e discs and diamond blades . • High-quality blades are often most economical. Lower quality blades often ha ve inf er ior cutting capacity and a shor ter ser vice lif e, which results in a higher cost in relation to the quan[...]

English – 11 SAFETY INSTR UCTIONS Diamond blades Diamond blades consist of a steel body pro vided with segments that contain industrial diamonds. Diamond blades ensure lo wer costs per cutting operation, f ewer b lade changes and a constant cutting depth. When using diamond blades mak e sure that it rotates in the direction indicated by the arro [...]

12 – English SAFETY INSTR UCTIONS General working instructions Cutting technique The technique described below is of a general character . Check inf or mation for each b lade regarding individual cutting characteristics (for e xample, diamond blades requires less f eeding pressure than an abrasive discs). • Suppor t the work piece in such a wa [...]

English – 13 SAFETY INSTR UCTIONS General rules • Ne ver start to cut with the upper quadrant of the blade as shown in the figure , also known as the kickbac k zone . • Alwa ys hold the machine in a firm grip with both hands. Hold it so that the thumbs and fingers grip round the handles. • K eep a good balance and a firm foothold. • A[...]

14 – English ASSEMBL Y Assemb ly Fitting the cutting blade Husqvarna’ s blades are approv ed for hand-held po wer cutters. Blades are manuf actured with three diff erent diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1"). Bushings can be fitted on the machine axle to adjust the machine to the centre hole [...]

English – 15 ST AR TING AND ST OPPING Bef ore star ting K3000 We t W ater connector • Connect the water hose to the w ater supply (A). The water is s witched on and off with the water tap (B). Star ting • Grip the front handle with the left hand. • Grip the rear handle with your right hand. • Press in the power s witch lock with your righ[...]

16 – English MAINTENANCE General Cleaning Cooling system The machine is equipped with an efficient f an to cool the motor . Cooling air which is drawn in through the g rille by the machines rear handle passes ov er the stator and rotor and out through the front of the motor housing. In order f or the machine to alwa ys be cooled sufficiently th[...]

English – 17 MAINTENANCE Bevel gear The grease in the gear housing should be changed e very 4 months. Use high quality gear grease The gear housing must not be filled completely with grease . The grease e xpands as the machine heats up during operation. If the gear housing was completely filled with grease it could damage the seals and lead to [...]

18 – English TECHNICAL D A T A ´®z+TM"¶6}¨ ´®z+TM"¶6}¨ Note 1: Handle vibrations are measured according to ISO 8662-4 Cutting equipment Max. blade speed, rpm 4500 Recommended cable dimensions T echnical data K3000 K3000 W et Engine Protection class I I Ground f ault circuit interrupter No Ye s Rated v oltage, V Europe 230 230 Gr[...]

English – 19 TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter Husqvarna K3000, K3000 Wet dating from 2008 ser ial numbers and onwards (the y ear is clear ly stated on the rating plate, f ollowed b y the[...]

´®z+TM"¶6}¨ 2009-05-05 ´®z+TM"¶6}¨ 1152450-26[...]