Husqvarna 2.010 BP инструкция обслуживания

Husqvarna Outdoor Products Italia SpA Via Como, 72 23868 V almadrera LC IT ALIA Phone + 39 0341 203111 - Fax + 39 0341 581671 PN 249958 REV . 00 (10/06) HANDLEIDING BELANGRIJKE IMPORT ANTS: Lees deze handleiding aan- dachtig en zorg dat u ailes begrijpt alvorens de kettingzaag te gebrulken en be-waar ze voor toekomstige raadpleging. BRUKERHÅNDBOK [...]

2 8 7 6 21 27 29 26 32 31 33 20 18 22 3 19 13 24 30 4 1 9 12 25 11 28 15 14 5 23 17 10 16 A B 13 14 D E1 E3 E4 E2 12 11 11 11 5 10 1 ltr 20 cm 3 5 100 10 200 15 300 20 400 50:1 2% Partner oil 1 ltr 25 cm 3 41 0 0 51 2 5 10 250 20 500 40:1 2,5% 2 Strokes engine totally synthetic oil or McCulloch oil[...]

40-43-46-49cc 52cc E5 E6 52 cc 40-43-46-49 cc H H F1 G I1 H1 H3 H4 I2 I3 L SUMMAR Y CHART TO IDENTIFY THE CORRECT GUARD NEEDED, WITH DIFFERENT CUTTING A TT ACHMENTS ÜBERSICHTST ABELLE ZUR AUSWAHL DES RICHTI- GEN SCHUTZBLECHES FÜR DIE EINZELNEN SCHNEIDWERKZEUGE T ABLEAU RECAPITULA TIF POUR LE CORRECT ACCOUPLEMENT LAME OU TETE FIL NYLON / DEFENSE D[...]

ENGLISH - 1 W arning Safety apparel: Appr oved protective goggles or visor , approved hard hat and hearing protection. Read the instructions for the user carefully and make sur e you under- stand how all the controls work. Safety apparel: Appr oved gloves. Safety apparel: Appr oved boots. Do not smoke when refueling or using the machine. Fuel enric[...]

2-E N G L I S H Use of the manual • A nyone who uses the machine should have read the entire m anual with extreme care. • A ll users should be familiar with the operat ions for use of the machine under absolutely safe conditions as d escribed in this m anual, and should be instructed in the proper cutting techniques to use, possibly by practica[...]

ENGLISH - 3 • pos sible contact with flying de bris. Never use a brush cutter without its safety pole guard correctly in place. Only use blades or nylon string head s clearly ma rked with a maximum s peed of at least 10,50 0 min -1 . Use only original or approved accessories and spare parts, which you can purchase from our official distributors. [...]

4-E N G L I S H obstacles. Use the machine holding it to the right of your body s o that the exhau st fumes can escape freely without obstruction from your clothing. While work ing, grip the brush cu tter firmly with both hands. Stand in a stable position on your feet. Keep the gr ips clean and dry. Do not use the br ush cutter while standing on a [...]

ENGLISH - 5 Shaft fastener  Use the shaft f astener every time you start the machine, fastening the connector to the supporting device. This way, the shaft will be held in place while your hands are busy with the starting procedure. Antivibration device The machine is equipped with an antivibration device (fig. A no. 30 ) which s erves to r educ[...]

E1. Setting the motor on the frame Position the motor so that the fuel cap faces upward and the bracket for fastening it to the frame is on one side. Screw pin A onto the motor as shown in the figure and tighten it secur ely . Fasten the motor to the frame and tighten it securely with the nut pr ovided (B). E2. Insertion of padding on frame Pick up[...]

ENGLISH - 7 Lower washer - e) Spacer - f) Rotating m ower gauge - g) Blade locking screw (length mm 34,5). Assembly of saw tooth blade and b lade guard  For assem bly see figures ( E7, E 8, E9 ).  Startup of cold engine F1. Stop switch ( A ) t urned to “I” oppos ite the “STOP ” mark. F2. Turn the fuel enrichment lever ( B ) to the clo[...]

8-E N G L I S H  After every use In order to avoid overheat ing the motor, remov e any dust a nd dirt from the slots on the cylinder cover and finds of the cylinder using a wooden scraper. Clean the backpack (if you wish, you can wash the padding after removing it from the frame). Store the machine in a dry place. After 25 hours o f use Remove t[...]

ENGLISH - 9 Drawing out the strin g During cutting, the ny lon string wears naturally causing an increase in the speed of t he engine and a reduced cutting capacity. When this happens, to bring out more string bump the head against the ground: re lease the throttle trigger to reduce the engine speed to less than 8000 rpm. Tap gently on t he ground [...]

10 - ENGLISH O. T echnical data N. Declaration of conformity The undersigned, authorized by Husqvarna Outdoor Products Italia SpA, declares that the following pr od- ucts model /TYPE: BC011, BC012 starting from the serial numbers pr oduced from 2006 on, manufac- tured by Husqvarna Outdoor Products Italia SpA, V almadrera, Italia, comply with Europe[...]