Husqvarna 325HS75X инструкция обслуживания

E E E E n n n n g g g g l l l l i i i i s s s s h h h h 325HS75 X-SERIES 325HS99 X-SERIES Oper ator ′ s manual Please read the operator’ s man ual carefully and mak e sure you understand the instructions before using the machine.[...]

2 – English KEY T O SYMBOLS Symbols W ARNING! Incorrect or careless use of a hedge trimmer can tur n it into a dangerous tool that can cause serious or ev en fatal injury . It is e xtremely impor tant that you read and understand the contents of this operator’ s manual. Please read the operator’ s manual carefully and make sure y ou understan[...]

English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Husqvarna AB has a policy of continuous product de velopment and theref ore reser ves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hear ing impairment. So alwa ys use approved hearing protecti[...]

4 – English SAFETY INSTR UCTIONS P ersonal pr otective equipment GLO VES Glov es must be wor n when required, f or e xample when fitting, inspecting or cleaning cutting attachments. HEARING PRO TECTION W ear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys w ear approv ed eye protection. If y ou use a visor then[...]

English – 5 SAFETY INSTR UCTIONS Vibration damping system Y our machine is equipped with a vibr ation damping system that is designed to minimise vibration and mak e operation easier . The machine ′ s vibration damping system reduces the transf er of vibration between the engine unit/cutting equipment and the machine ′ s handle unit. The engi[...]

6 – English SAFETY INSTR UCTIONS • Check that the throttle control and throttle loc k move freely and that the return spr ings work properly . • See instructions under the heading Star t. Star t the hedge trimmer and apply full throttle. Release the throttle trigger and check that the b lades stop and remain stationar y . If the blades mo v e[...]

English – 7 SAFETY INSTR UCTIONS Assembl y of the catcher (accessory) Loosen the nuts on top of the bar . Align the bolts in the holes on the catcher and fit the bolts. Adjust the b lades' contact pressure according to the instructions under the heading Blades Gear housing • The gear housing gets hot when the machine has been in use. T o [...]

8 – English SAFETY INSTR UCTIONS T ranspor t and storage • Store and transpor t the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames, f or example , from electrical machiner y , electric motors, electrical relays/s witches or boilers. • When storing and transpor ting fuel alwa [...]

English – 9 SAFETY INSTR UCTIONS • Check the w orking area for f oreign objects such as electricity cables, insects and animals , etc, or other objects that could damage the cutting attachment, such as metal items. • If any f oreign object is hit or if vibrations occur stop the machine immediately . Disconnect the HT lead from the spark plug.[...]

10 – English WHA T IS WHA T? What is what? 1 2 20 3 4 6 7 8 9 10 11 12 13 14 15 16 5 17 18 19 1 Operator ′ s manual 2 Grease nipple 3 Gear housing 4 Blades 5 Hand guard 6 F ront handle 7 Cylinder cov er 8 Star ter handle 9 Fuel cap 10 Fuel tank 11 Air purge 12 Choke control 13 Throttle lock 14 Throttle control 15 Stop s witch 16 Air fi lter co[...]

English – 11 FUEL HANDLING Fuel CA UTION! The machine is equipped with a tw o-stroke engine and must alwa ys been run using a mixture of petrol and two- stroke engine oil. It is important to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, e ven small inaccuracies[...]

12 – English ST AR TING AND ST OPPING Chec k bef ore star ting • Inspect the working area. Remov e an y objects that could be thrown out. • Check the cutting attachment. Ne ver use blades that are dull, crac ked or damaged. • Check that the machine is in perf ect working order . Check that all nuts and scre ws are tight. • Make sure the g[...]

English – 13 ST AR TING AND ST OPPING W arm engine Ignition: Set the stop s witch to the star t position. Choke: Set the choke control in the chok e position and then back to its original position. This only engages the star t throttle setting without any chok e. Air purge: Press the air purge diaphragm repeatedly until fuel begins to fi ll the [...]

14 – English MAINTENANCE Carb urettor Y our Husqv ar na product has been designed and manuf actured to speci fi cations that reduce har mful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. T o ensure that it contin ues to run at peak perf ormance and to minimise har mful exhaust emissions after the running-in p[...]

English – 15 MAINTENANCE The blades m ust also remain stationar y when the chok e control is in the star t throttle position. W ARNING! If the idle speed cannot be adjusted so that the cutting attachment stops, contact y our dealer/service workshop . Do not use the machine until it has been correctly adjusted or repaired. High speed jet H The hig[...]

16 – English MAINTENANCE Cooling system T o keep the w orking temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter . 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder . 4 Cylinder cov er (directs cold air over the cylinder). Clean the cooling system wit[...]

English – 17 MAINTENANCE Gear housing There is a grease nipple on the gearbo x. Use a grease gun to top up with grease. This should be carried out after appro ximately e very 20 working hours. Use Husqvarna special grease, No . 503 98 96-01. CA UTION! The gear housing must not be fi lled completely with grease. The grease e xpands as the machine[...]

18 – English TECHNICAL D A T A ´®z+H1|¶6A¨ ´®z+H1|¶6A¨ T echnical data Note 1: Noise emissions in the environment measured as sound pow er (L WA ) in conf ormity with EC directive 2000/14/EC . Note 2: Equivalent sound pressure le v el is calculated as the time-weighted energy total f or sound pressure lev els under various working conditi[...]

English – 19 TECHNICAL D A T A EC-dec laration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-561 82 Huskv ar na, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 325HS75 and 325HS99 from 2002 ’ s serial numbers and onwards (the y ear is clearly stated in plain text on the type plate wi[...]

´®z+H1|¶6A¨ 2003-04-02 ´®z+H1|¶6A¨ 1140179-26[...]