Husqvarna 8527SBEB инструкция обслуживания

8527SBEB Owner's Manual[...]

2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury . W ARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e[...]

3 CONGRA TULA TIONS on your purchase of a new snow thrower . It has been designed, engineered and man ufactured to give best possible dependability and per formance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center/department. We have competent, well-trained tech- nicians and the pro[...]

4 P ARTS P ACKED SEP ARA TEL Y IN CART ON[...]

5 ASSEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiarize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sembled at the factory w[...]

6 ASSEMBL Y / PRE-OPERA TION INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 2. W ith top end of rod positioned under right side of control panel, push down on rod and insert[...]

7 ASSEMBL Y / PRE-OPERA TION CHECK TIRE PRESSURE The tires on your snow thrower were overinfl ated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI. INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provi[...]

8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat[...]

9 OPERA TION Choke control - used for starting a cold engine. T raction drive control lever - used to engage power-pro- pelled for ward or reverse motion of snow thrower . Defl ector remote control lever - used to change the distance the snow is thrown. Auger control lever - used to engage auger motion (throw snow). Discharge chute control lever -[...]

10 TO USE CHOKE CON TROL (See Fig. 13) The choke con trol is located on the en gine. Use the choke control when ever you are starting a cold en gine. Do not use to start a warm en gine. The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shiel[...]

11 TO MOVE FOR W ARD AND BACKW ARD (See Fig. 17) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system. • Release traction drive control lever to stop the forward or revers[...]

12 TO ADJUST SKID PLA TES (See Fig. 18) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow i[...]

13 COLD ST ART - ELECTRIC ST AR TER 1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place throttle control in F AST position. 3. Rotate choke control to FULL position. 4. Connect the power cord to the engine. 5. Plug the o[...]

14 MAINTENANCE LUBRICA TION CHART GENERAL REC OMMENDA TIONS The warranty on this snow thrower does not cover items that have been sub jected to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in structed in this manual. Some ad just- ments will need to be made periodically to properly [...]

15 MAINTENANCE V- B E LT S Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad justable. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual). The V -belts on your snow thrower are of special con[...]

16 W ARNING: T o avoid serious injury , before per- forming any service or ad justments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. SNOW THROWER [...]

17 SER VICE AND ADJUSTMENTS TO REPLACE BEL TS (See Fig. 22) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a qualifi ed service center . NOTE: It is recommended that both the auger and traction drive belt be repl[...]

18 ST ORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. W ARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open fl ame, spark or pilot light as on a furnace, water heater , clothes dryer or gas ap pliance.[...]

19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Refi ll fuel tank with fresh, clean gasoline. 4. Throttle in STOP position. 4. Move throttle to F AST position. 5. Choke in OFF position[...]

20 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO. 8527SBEB (96193001 100), PRODUCT NO. 961 93 00-1 1 22 18 21 53 19 28 19 55 28 19 55 54 54 6 6 5 6 6 9 12 7 7 8 6 11 27 27 30 26 25 24 23 20 31 25 24 26 23 29 21 53 19 20 18 10 13 4 14 16 15 36 37 50 47 42 44 27 43 46 38 45 27 43 42 41 40 39 34 32 49 19 48 51 33 35 56[...]

21 KEY P ART NO. NO. DESCRIPTION 4 532 19 10-79 Pulley , Impeller 5 532 18 89-09 Bearing Assembly , Flange 6 532 15 53-77 Nut, Hex Flange 5/16-18 7 532 18 03-55 Bolt, Flat Head, Carriage 5/16-18 x 5/8 8 872 27 05-05 Bolt, Carriage 5/16-1 8 x 5/8 9 532 17 88-20 Nut, Cage 3/8-16 10 532 18 82-1 1 Housing, Auger 1 1 532 18 40-90 Bar , Scraper 12 532 18[...]

22 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 8527SBEB (96193001 100), PRODUCT NO. 961 93 00-1 1 3 2 1 1 2 6 19 2 2 14 26 28 27 27 25 20 29 24 31 30 7 4 5 6 8 8 16 18 17 10 14 3 13 15 9 22 11 12[...]

23 KEY P ART NO. NO. DESCRIPTION 1 532 18 33-34 Knob, Lever 2 817 50 10-10 Screw #10-24 x 5/8 3 532 19 84-75 Control Assembly , Defl ector 4 873 80 06-00 Nut, Lock 3/8-16 5 819 13 13-16 Washer , Flat 3/8 6 532 19 84-73 Control Assembly , Chute Rotater 7 532 18 40-89 Support, Pivot 8 532 15 00-78 Screw, Hex Head 5/16-18 x 3/4 9 532 18 45-05 Spring,[...]

24 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO. 8527SBEB (96193001 100), PRODUCT NO. 961 93 00-1 1 32 31 32 30 31 12 10 11 13 15 15 12 16 17 16 23 22 27 41 27 22 17 11 15 15 14 38 39 40 37 33 35 35 34 34 42 43 44 45 46 46 7 6 36 2 5 5 3 1 4 4 4 4 3 8 28 28 9 18 19 20 21 26 24 24 25 5 5 29[...]

25 KEY P ART NO. NO. DESCRIPTION 1 532 18 41-10 Lever, Auger Control, RH 2 532 18 41-09 Lever, T raction Drive Control, LH 3 532 19 96-39 Nut, Cage 1/4-20 4 532 17 88-88 Bushing, Flange 5 532 16 96-75 Retainer, Hairpin 6 532 19 96-40 Screw, Hex Head 1/4-20 x 3/4 7 532 17 86-52 Rod, Interlock 8 532 19 95-76 Arm, Impeller Rod 9 532 19 95-75 Arm, Trac[...]

26 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO. 8527SBEB (96193001 100), PRODUCT NO. 961 93 00-1 1 4 4 4 1 2 5 3 5 1 2 3 1 20 21 17 19 18 18 7 7 2 2 2 24 23 12 32 27 44 22 16 15 2 4 4 13 1 2 5 3 42 42 3 5 8 9 10 6 3 41 14 43 11 35 33 15 41 22 34 29 22 31 26 25 28 30 40 39 38 36 37 33[...]

27 KEY P ART NO. NO. DESCRIPTION 1 532 14 63-15 Screw, Hex Head 5/16-18 x 3/4 2 873 80 05-00 Nut, Lock 5/16-18 3 532 15 54-15 Washer , Flat 4 817 49 05-08 Screw, Hex Head 5/16-18 x 1/2 5 532 18 00-17 Bearing, Flange 6 532 18 01-34 Shaft, Auxiliary 7 532 17 92-70 Spacer, Plate 8 532 19 29-07 Plate, Auxiliary 9 532 18 00-82 Gear, Intermediate (12/58)[...]

28 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 8527SBEB (96193001 100), PRODUCT NO. 961 93 00-1 1 6 19 17 10 21 22 23 2 1 3 4 6 7 8 9 12 13 15 27 26 25 24 18 7 6 20 14 47 47 48 46 40 44 49 50 51 52 35 55 34 33 32 38 36 41 6 37 39 42 43 11 53 54 5 5 5 11 44 45 41 11 16 56 30 29 31 31 10 21 28 57 6 58[...]

29 KEY P ART NO. NO. DESCRIPTION 1 532 18 10-44 Spring, Traction Idler 2 532 18 05-22 Pulley , Idler (2-1/4) 3 - - - Engine, Briggs & Stratton, Model Number 15B1 14 (For engine ser - vice / replacement parts, call Briggs & Stratton at 1-800-233-3723) 4 874 78 05-20 Screw, Hex Head 5/16-18 x 1-1/4 5 532 15 00-78 Screw, Hex Head 5/16-18 x 3/4[...]

30 REP AIR P ARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 8527SBEB (96193001 100), PRODUCT NO. 961 93 00-1 1 3 2 4 4 5 5 6 6 4 4 1 2 5 3 4 2 10 7 6 8 9 1 11 3 13[...]

31 KEY P ART NO. NO. DESCRIPTION 1 532 18 78-33 Wheel Assembly , 16", LH 2 532 15 54-43 Pin, Klik 1/4 3 532 18 78-65 Wheel Assembly , 16", RH 4 532 14 63-15 Screw, Hex Head 5/16-18 x 5/8 5 532 17 98-30 Bearing, Axle 6 532 17 46-97 Washer , Thrust (1") KEY P ART NO. NO. DESCRIPTION 1 532 18 10-38 Decal, Danger 2 532 19 13-76 Decal, Hu[...]

532 40 37-57 Rev . 1 12.21.05 BY Printed in U.S.A. S E C T I ON 1: L I MIT E D W A R R A N T Y Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original pur- chaser to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below: L[...]