Husqvarna PA 1100 инструкция обслуживания

E E E E n n n n g g g g l l l l i i i i s s s s h h h h Sa w attachment P A P A 1100 Accessoir e de sciage P A P A 1100 Suplemento de sierr a P A P A 1100 Oper ator ′ s manual Manuel d’utilisa tion Manual de instr ucciones GB FR ES[...]

2 – English KEY T O SYMBOLS . Symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear: • A protective helmet wh[...]

English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Husqvarna AB has a policy of continuous product de velopment and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hear ing impairment. So always use appro ved hearing protection[...]

4 – English SAFETY INSTR UCTIONS Cutting equipment This section describes how you can achie ve maximum clearing capacity and extend the lif e of the cutting attachment through correct maintenance and using the right type of cutting attachment. Only use cutting equipment recommended b y us! See the T echnical data section. Keep the chain’ s cutt[...]

English – 5 SAFETY INSTR UCTIONS Chain • Saw chain pitch (inches). (The distance between three drive links, divided b y two .) • Drive link width (mm/inches) • Number of drive links. Sharpening y our chain and adjusting raker c learance General information on sharpening cutting teeth • Ne ver use a blunt chain. When the chain is blunt you[...]

6 – English SAFETY INSTR UCTIONS • Alwa ys file cutting teeth from the inside face outw ards. Reduce the pressure on the return stroke. File all the teeth on one side of the bar first. Then turn the saw o ver and file the remaining teeth from the other side. • File all the teeth to the same length. When the length of the cutting teeth is r[...]

English – 7 SAFETY INSTR UCTIONS 1 Undo the bar nut. 2 Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner . Tighten the chain until it does not sag from the underside of the bar . 3 Use the combination spanner to tighten the blade n ut while holding up the tip of the bar . Check t[...]

8 – English SAFETY INSTR UCTIONS 2 Check that the oil channel in the gear housing is clean. Clean if necessar y . 3 Check that the bar tip sproc ket turns freely . If the chain lubrication system is still not working after carr ying out the abov e checks you should contact y our ser vice workshop. Chec king wear on cutting equipment Chain Check t[...]

English – 9 SAFETY INSTR UCTIONS P ersonal pr otection • Alwa ys wear boots and other equipment described under the heading P ersonal protective equipment in the machine’ s Operator’ s Manual. • Alwa ys wear working clothes and heavy-duty long trousers. • Ne ver wear loose clothing or jew eller y . • Make sure y our hair does not hang[...]

10 – English SAFETY INSTR UCTIONS • Alwa ys slow the engine to idle speed after each working operation. Long per iods at full throttle without any load on the engine can lead to serious engine damage. • Alwa ys work at full throttle. • Let the engine drop back to idle speed betw een each cut. Long periods at full throttle can cause ser ious[...]

English – 11 WHA T IS WHA T? What is what on the saw attac hment? (Saw attachment with shaft P A 1100) 11 9 1 2 8 6 5 4 10 7 13 12 14 15 3 11 1 Be vel gear 2 Chain lubrication adjustment screw 3 Shaft (1100 mm) 4 Harness suppor t hook 5 Protective guard f or saw chain 6 Bar nut 7 Chain tensioning screw 8 Chain 9 Bar 10 Chain oil tank 11 Filling w[...]

12 – English WHA T IS WHA T? What is what on the saw attac hment? (Saw attachment without shaft P A) 10 8 1 2 7 5 4 3 9 6 12 11 13 14 10 1 Be vel gear 2 Chain lubrication adjustment screw 3 Harness suppor t hook 4 Protective guard f or saw chain 5 Bar nut 6 Chain tensioning screw 7 Chain 8 Bar 9 Chain oil tank 10 Filling with chain oil 11 Operato[...]

English – 13 ASSEMBL Y Fitting the cutting head (Saw attachment with shaft P A 1100) • Fit the cutting head on the shaft so that the screw (A) is aligned with the hole in the shaft as shown. • Tighten screw A. • Tighten screw B . CA UTION! Make sure that the drive shaft inside the shaft engages with the cut-out in the cutting head. Fitting [...]

14 – English ASSEMBL Y Adjusting the harness Y ou should alwa ys use the har ness with the machine to give maximum control ov er the machine and reduce the risk of f atigue in your ar ms and back. • Put on the harness. • Hook the machine onto the harness suppor t hook. • Adjust the length of the harness so that the suppor t hook is roughly [...]

English – 15 TECHNICAL D A T A T echnical data Note 1: Equivalent sound pressure le vel is calculated as the time-weighted energy total f or sound pressure lev els under various working conditions with the follo wing time distr ibution: 1/2 idling and 1/2 max speed. Bar and chain combinations The f ollowing combinations are CE approved. T echnica[...]

16 – English TECHNICAL D A T A EC-dec laration of conformity (Applies to Europe onl y) W e, Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel +46-36-146500, declare that this saw attachment from 2002’ s ser ial numbers and onwards (the y ear is clearly stated in plain text on the type plate, with subsequent serial number), complies with the requ[...]

´®z+H8r¶0_¨ 2004-02-05 ´®z+H8r¶0_¨ 1140248-26 20[...]