Husqvarna RZ4221 BF / 967176101 инструкция обслуживания

RZ4221 BF / 967176101 Operator Manual Please read the operator’ s manual car efully and mak e sur e you understand the instructions befor e using the machine. Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of an y gasoline exceeding 10% ethanol (E10) will v oid the product war ranty .[...]

When this product is worn out and no longer used, it should be returned to the reseller or other party for recycling. ©2012 All rights reserved. Orangeburg, SC. Printed in U.S.A. In order to implement improvements, specifications and designs can be altered without prior notification. Note that no legal demands can be placed based on the informat[...]

CONTENTS INTRODUCTION ............................................................... 5 General ....................................................................... 5 Driving and T ransport on Public Roads ...................... 5 T owing ........................................................................ 5 Operating .......................[...]

W ARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower . Each person operating the mower must be of sound mind and body and must not be under the in[...]

INTRODUCTION 5 Congratulations Thank you for purchasing a Husqvarna ride-on mower . This machine is built for superior efficiency to rapidly mow primarily large areas. A contr ol panel easily accessible to the operator and a hydrostatic transmission regulated by steering contr ols both contribute to the machine’s perfor mance. This manual is a v[...]

INTRODUCTION 6 Good Service Husqvarna’s products are sold all over the world and only in specialized retail stor es with complete service.. This ensures that you as a customer r eceive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer . See the certifica[...]

SYMBOLS AND DECALS 7 R N These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean. IMPORT ANT INFORMA TION Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. Reverse Neutral Fast Slow Choke Fuel W arning! Parking Brake CE conformity marking. Only for Europea[...]

SYMBOLS AND DECALS 8 Moving sharp blades under cover W arning! Rotating blades, keep away from the discharge deck Battery acid is corrosive, explosive and flammable Read Operator’s Manual Shut off engine and remove key befor e perfor ming any maintenance or repair work Keep a safe distance from the machine Use on slopes no greater than 10° No p[...]

SAFETY 9 Safety Instructions These instructions are for your safety . Read them carefully . General Operation • Read, understand, and follow all instructions on the machine and in the manual before starting. • It is recommended that someone be awar e that you are mowing and can pr ovide help in case of injury or accident. • Do not put hands o[...]

SAFETY 10 • Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher , or unclogging the discharge guard. • Operate machine only in daylight or good artificial light. • Do not operate the machine while under the influence of alcohol or drugs. [...]

SAFETY 11 Personal Safety Equipment • Make sure that you have first aid equipment close at hand when using the machine. • Never use the machine when barefoot. • Always wear protective shoes or boots, pr eferably with steel toe caps. • Always wear approved pr otective glasses or a full visor when assembling or driving. • Always wear glove[...]

SAFETY 12 8011-517 Ne ver allo w children to operate the machine 8011-518 K eep children awa y from work area Children T ragic accidents can occur if the operator is not alert to the presence of children. Childr en are often attracted to the machine and the mowing activity . Ne v er assume that children will r emain out of the path of danger . • [...]

SAFETY 13 Safe Handling of Gasoline W ARNING! The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed. W ARNING! The engine and the exhaust system become very hot during operation. There is risk for burns if touched. Allow engine and exhaust system to cool before refueling[...]

SAFETY 14 8011-515 Ne ver driv e the machine in an enclosed space General Maintenance • Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation r egularly . • Keep machine free of grass, leaves, or other de[...]

SAFETY 15 Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury . Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery . 6003-009 Do not smoke when perf or ming maintenance on the batter y . [...]

SAFETY 16 IMPORT ANT INFORMA TION The parking brake is not sufficient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over . W ARNING! Escaping hydraulic oil under pressure can have sufficient force to penetr[...]

CONTROLS 17 This operator’s manual describes the Husqvarna Zero T urn Rider . The rider is fitted with a four -stroke overhead valve engine. T ransmission from the engine is made via belt-driven hydraulic pumps. Using the left and right steering controls, the flow is r egulated and thereby the direction and speed. 1. Cutting height handle 2. Pa[...]

CONTROLS 18 8050-003 Steering controls Steering Control Levers The machine’s speed and direction ar e continuously variable using the two steering controls. The steering controls can be moved forwar d or backward about a neutral position. Further more, ther e is a neutral position, which is locked if the steering controls ar e moved outward. When[...]

CONTROLS 19 Throttle Control The throttle contr ol regulates the engine speed and thereby the rate of r otation of the blades. In order to incr ease or decrease the engine speed, the control is moved forwar d or back respectively . Avoid idling the engine for long periods, as ther e is a risk of fouling the spark plugs. USE FULL THROTTLE WHEN MOWIN[...]

CONTROLS 20 Choke Control The choke control is used for cold starts in order to provide the engine with a richer fuel mixtur e. For cold starts the throttle knob should be pushed forward all of the way . Refueling Read the safety instructions before r efueling. The machine has one fuel tank, just behind the seat. The tank volume is 3 gallons (11.4 [...]

CONTROLS 21 Fuel Shut Off V alve The fuel shut off valve is located in the fuel line under the seat. Tilt seat forward for access. The fuel valve is ON when the valve is parallel to the fuel line. Rotate the valve ¼ turn clockwise to tur n fuel OFF . 8050-010 Fuel shut off valv e in the OPEN position. 8058-085 The mower dec k’ s lifting le ver M[...]

CONTROLS 22 Bypass Linkages When pushing or pulling the mower , be sure to engage the EZT Hydrogear bypass linkages. The EZT bypass linkages are located on the r ear of the frame, below the rear engine guar d. See Moving Mac hine By Hand in the Operation section. 8050-018 Set bypass linkages into slots on both sides Blade Control Lever T o engage t[...]

OPERA TION 23 Read the Saf ety section and following pages, if you are unfamiliar with the machine. T raining Due to unique steering capabilities, zero turn mowers are far mor e maneuverable than typical riding mowers. This section should be reviewed in its entir ety prior to attempting to move the mower under its own power . When first operating [...]

OPERA TION 24 Before Starting • Read the sections Safety Instructions and Controls befor e star ting the machine. • Perfor m the daily maintenance before starting (see Maintenance Schedule in the Maintenance section). • Check that there is sufficient fuel in the fuel tank. • Adjust the seat to the desired position. The following conditions[...]

OPERA TION 25 8050-008 Set the throttle 8050-028 Place controls in neutral position 8050-007 Choke control 5. Move the steering controls outwar d to the locked (outer) neutral position. 6. Move the throttle to the middle position. 7. If the engine is cold, the choke control should be pushed forward to its extent.[...]

OPERA TION 26 8050-135 T urn to ST AR T position 8050-136 Release ignition to the R UN position 8050-010 Open the fuel valv e 8. Open the fuel valve. IMPORT ANT INFORMA TION Do not run the starter for more than 5 seconds each time. If the engine does not start, wait approximately 10 seconds before retrying. 9. Press in and turn the ignition key to [...]

OPERA TION 27 Slowly slide the choke control back to the middle position when the engine has started. Set the desired engine speed with the thr ottle. Allow the engine to run at a moderate speed, approximately mid throttle, for 3-5 minutes befor e loading it too heavily . USE FULL THROTTLE WHEN MOWING (no choke). W ARNING! Engine exhaust and certai[...]

OPERA TION 28 Running 1. Release the parking brake by moving the lever downward. NOTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. 2. Move the steering controls to the neutral position (N). W ARNIN[...]

OPERA TION 29 Operating on Hills Read the Safety Instructions Driving on Slopes in the Saf ety Instructions . • The slowest speed possible should be used before starting up or down hills. • Avoid stopping or changing speed on hills. • If stopping is absolutely necessary , pull drive levers into the neutral position and push to the outside of [...]

OPERA TION 30 Mowing Tips • Observe and flag rocks and other fixed objects to avoid collisions. • Begin with a high cutting height and reduce it until the desired mowing r esult is attained. The average lawn should be cut to 2½" (64 mm) during the cool season and over 3" (76 mm) during the hot months. For healthier and better looki[...]

OPERA TION 31 Stopping the Engine Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. A void idling the engine for longer periods, as there is a risk of the spark plugs fouling. 1. Disengage the mower deck by sliding the blade control lever out of the lock notch and down [...]

OPERA TION 32 Moving Machine By Hand When pushing or pulling the mower , be sure to engage the EZT Hydrogear bypass linkages. The EZT bypass linkages are located on the r ear of the frame, below the rear engine guar d. 1. Raise the deck into the highest cutting position. 2. Pull the EZT bypass linkages out and into the slots. Release linkages to ho[...]

MAINTENANCE 33 Maintenance Schedule The following is a list of maintenance procedur es that must be perfor med on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best possible condition and[...]

MAINTENANCE 34 1) First change after 5-8 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours. 2) In dusty conditions, cleaning and replacement ar e requir ed more often. 3) For daily use, the machine should be lubricated twice weekly . 4) Perfor med by authorized service workshop. ● = Described in this [...]

MAINTENANCE 35 Battery Y our mower is equipped with a maintenance free battery that does not need servicing. However , periodic charging of the battery with an automotive type battery charger will extend its life. • Keep battery and ter minals clean. • Keep battery bolts tight. • See chart for charging times. Cleaning battery and terminals Co[...]

MAINTENANCE 36 Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: 1. The mower deck is disengaged. 2. The steering controls ar e in the outer , locked neutral position. 3. The driver is sitting in the driver’s seat. 4. The parking brake [...]

MAINTENANCE 37 Parking Brake Visually check that no damage is found on the lever , links, or switch belonging to the parking brake. Perfor m a standstill test and check that there is sufficient braking action. T o adjust the parking brake, contact the Husqvarna service workshop. W ARNING! Faulty adjustment can result in reduced braking ability and[...]

MAINTENANCE 38 2 1 3 W ARNING! The engine and the exhaust system, become very hot during operation. Risk for burns if touched. Allow engine and exhaust system to cool before servicing. EZT Belt T o replace EZT belt Park the mower on a level surface. Engage the park brake. EZT belt removal NOTE: Be careful not to damage the fan blades on the EZT as [...]

MAINTENANCE 39 Adjusting the Mower Deck W ARNING! Before performing any service or adjustment checklist: 1. Engage the parking brake. 2. Place the Blade switch in the disengaged position. 3. T urn ignition switch to OFF position and remove the key . 4. Make sure the blades and all moving parts have completely stopped. 5. Disconnect the spark plug w[...]

MAINTENANCE 40 2 1 3 Caster Wheels Check every 200 hours. Check that wheels rotate freely . If wheels do not r otate freely take the unit to your dealer for service. Foam filled tires or solid tir es will void the warranty . Removal and installation of caster wheel 1. Remove nut (1) and caster bolt (2). 2. Pull the wheel out of the fork and take c[...]

LUBRICA TION 41 General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be filled with engine oil. When lubricating with gr ease, unless otherwise stated, use a high grade molybdenum disulphide grease. For daily use, the machine should be lubricated twice weekly . 12/12 Every[...]

LUBRICA TION 42 Front Wheel Mount Lubricate with a grease gun, one zerk for each wheel mount. Use only good quality bearing grease. Grease fr om well-known brand names (petrochemical companies, etc.) usually maintains a good quality . Front Wheel Bearings Lubricate with a grease gun, one zerk for each set of wheel bearings. Use only good quality be[...]

TROUBLESHOOTING 43 Problem / Cause Engine will not start • Blade lever is engaged • Steering controls ar e not locked in neutral position • Driver is not sitting in driver’s seat • Parking brake is not activated • Battery is dead • Contamination in carburetor or fuel line • Fuel supply is closed or tap for fuel tank is in wrong posi[...]

TROUBLESHOOTING 44 Problem / Cause Engine overheats • Clogged air intake or cooling fins • Engine overloaded • Poor ventilation around engine • Defective engine speed regulator • Soot in the combustion chamber • T oo little or no oil in the engine • Fouled spark plug Battery not charging • Poor contact with battery ter minal cable [...]

ST ORAGE 45 Winter Storage The machine should be readied for storage at the end of the mowing season or if it will not be in use for longer than 30 days. Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carbur etor and disrupt engine function. Fuel stabilizers are an acceptable option as r[...]

46 WIRING DIAGRAM 8053-002[...]

TECHNICAL DA T A 47 (1 The power rating of the engines indicated is the average net power output (at specified rpm) of a typical production engine for the engine model measured to SAE standar d J1349/ISO1585. Mass production engines may differ fr om this value. Actual power output for the engine installed in the final machine will depend on the o[...]

TECHNICAL DA T A 48 HEX HEAD CAP SCREWS The torque values shown should be used as a general guideline when specific tor que values are not given. U.S. Standard Hardware Grade SAE Grade 5 SAE Grade 8 Flangelock Screw w/Flangelock Nut Shank Size (Diameter in inches, fine or coarse thread) Size ft./lbs Nm ft./lbs Nm ft./lbs Nm ¼ 9 12 13 18 5 / 16 1[...]

49 CONFORMITY CERTIFICA TES USA requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requir ements. This is also applicable to special requir ements for any of the states, (Califor nia emission rules etc.). Do not remove any of these labels. Certificates can also be supplied with [...]

50 SER VICE JOURNAL Action Date, mtr reading, stamp, sign Delivery Service Charge battery . Adjust tire pr essure of all wheels according to T echnical Data. Mount the steering controls in the normal position. Connect the contact box to the cable for the seat’s safety switch. Check that the right amount of oil is in the engine. Adjust the positio[...]

51 SER VICE JOURNAL Action Date, mtr reading, stamp, sign After the First 10 Hours Change engine oil. 25-Hour Service Check the fuel pump’s air filter . Check the hydraulic system’s oil level. Check the tire pr essures. Lubricate the belt adjuster , mower deck. Lubricate the belt adjuster , hydraulic pumps. Check/clean the engine’s cooling a[...]

52 SER VICE JOURNAL Action Date, mtr reading, stamp, sign 50-Hour Service Perfor m the 25-hour service. Clean/replace the air cleaner’s paper filter cartridge (shorter intervals for dusty operating conditions). Change engine oil. Lubricate according to lubrication chart. Check/adjust the parking brake. 100-Hour Service Perfor m the 25-hour servi[...]

53 SER VICE JOURNAL Action Date, mtr reading, stamp, sign 300-Hour Service Perfor m the 25-hour service. Perfor m the 50-hour service. Perfor m the 100-hour service. Check/adjust the mower deck. Clean the combustion chamber and grind the valve seats. Check the engine valve clearance. Replace the air cleaner’s foam prefilter . At Least Once Each [...]

54 SER VICE JOURNAL Action Date, mtr reading, stamp, sign[...]

[...]

1 15 498228 Rev A 2012-06-01 www .husqvarna.com[...]