IBM CIO-DIO48H инструкция обслуживания

[...]

CIO-DIO48H Digit al Input/Output Board User ’ s Guide Document Revision 1, December, 2006 © Copyright 2006, Measurement Computing Corporation[...]

Your new Measurement Computing product comes w ith a fantastic extra — Management committed to your satisfaction! Refer to www.mccdaq.com/execteam.html for the names, titles, and contact inform ation of each key executive at Measurement Computing. Thank you for choosing a Measurement Computing product—and congratulations! You own the finest, an[...]

Trademark and Copy right Information TracerDAQ, Universal Library, Harsh Environment Warranty, Measurement Computing Corpor ation, and the Measurement Computing logo are either trademarks or registered trademarks of M easurement Computing Corporation. Windows, Microsoft, and Visual Studio are either trademarks or registered trademarks of Microsoft [...]

Table of Contents Preface About this U ser's Gu ide .......................................................................................................................6 What you will learn from this user's guide ..................................................................................... .................... 6 Conventions in [...]

Preface About this User's Guide What you will learn from this user's guide This user's guide explai ns how to install, configure, and use t he CIO-DIO48H board so that you get the m ost out of its analog output features. This user's guide al so refers you to related docum ents available on our web site, and to technical support [...]

Chapter 1 Introducing the CIO-DIO48H Overview: CIO-DIO48H features The CIO-DIO48H provides 48-bits of digi tal I/O. The I/O i s organized into two 24-bit groups based on an 82C55 mode 0 em ulation. Each 24-bit group is divided into t hree eight-bit ports l abeled A n , B n and C n , where n is either "1" for FIRSTPORT or "2" for[...]

Chapter 2 Installing the CIO-DIO48H What comes with your CIO-DIO48H shipment? The following items are shipped with the CIO-DIO4 8H. Hardware  CIO-DIO48H Additional documentation In addition to this hardware user's guide, you should also receive the Quick Start Guide (available in PDF at www.mccdaq.com /PDFmanuals/DAQ-Software-Quick-Start.pd[...]

CIO-DIO48H User's Guide Installing the CIO-DIO48H Unpacking the CIO-DIO48H As with any electronic devi ce, you should take care while handling to avoid dam age from stat ic electricity . Before removing t h e CIO-DIO48H from it s packaging, ground yourself using a wrist strap or by simply t ouching the computer chassi s or other grounded objec[...]

CIO-DIO48H User's Guide Installing the CIO-DIO48H Disregard the numbers printed on the sw itch When setting the base address, refer to the numbe rs printed in white on the printed circuit bo ard. PC I/O Address Summary Hex Range Function Hex Range Function 000-00F 8237 DMA #1 2C0-2CF EGA 020-021 8259 PIC #1 2D0-2DF EGA 040-043 8253 TIMER 2E0-2[...]

CIO-DIO48H User's Guide Installing the CIO-DIO48H Connecting the board for I/O operations Connectors, cables – main I/O connector The table below lists the board connector, applicable cables, and compatible accessory products. Board connector, cables, and accessory equipment Connector type 50-pin shrouded male header Compatible cables C50FF-[...]

CIO-DIO48H User's Guide Installing the CIO-DIO48H Cabling The red stri pe id e n ti fi es p in # 1 50-pin Female IDC conn ector 50-pin F emale IDC Conne ctor 1 2 49 50 2 50 1 49 Figure 3. C50FF-x cable Field wiring, signal termi nation, and conditioning You can use the following cabling, screw t erminati on, and signal conditioning products wi[...]

Chapter 3 Functional Details 82C55 emulation The CIO-DIO48H emulates the 82C55 chip. The 82C55 em ulation initializes all por ts as inputs on power-up and reset. A TTL input is a high im pedance input. If you c onnect another TTL input device to the output, it could be turned on or off every tim e th e board is reset. To establish a consistent TTL [...]

CIO-DIO48H User's Guide Functional Details 2.2 K SIP inst al led for pull-up 2.2 K SIP Dot +5 V DC HI LO (GND) n7 User Con n ector Digital I/O Lines n5 n4 n3 n2 n1 n0 n6 COM Digital I/O Port n = A, B, o r C 2.2 K SIP Dot +5 VDC HI LO (GND) n7 User Con n ector Digital I/O Lines n5 n4 n3 n2 n1 n0 n6 COM 2.2 K SIP instal led for pull-dow n Digita[...]

CIO-DIO48H User's Guide Functional Details CIO-ERB24 or SSR-RACK24 CIO-ERB24 or SSR-RACK24 CIO-DIO48H IN IN OUT OUT Figure 6. CIO-DIO48H to CIO-ERB24 or SSR-RACK24 daisy chain The 24 digital I/O bi ts on pins 25 to 48 (base address +0 through +2) control the first relay board. The 24 digital I/O bi ts on pins 1 to 24 control the second relay/S[...]

Chapter 4 Programming and Developing Applications After following the i nstallation i nstructions in Chapte r 2, your board should now be install ed and ready for use. In general there may be no correspondence am ong registers fo r different boards. Software written at the register level for other models will not function correctly with yo ur board[...]

Chapter 5 Specifications Typical for 25 °C unless otherwise specified. Specifications in italic text are guaranteed by design. Digital input/output Table 1. DIO specifications Digital type 8255 mode 0 emulation  Output: 74S244  Input: 74LS373 Configuration 4 banks of 8, 4 banks of 4, programmable by bank as input or output Number of channels[...]

CIO-DIO48H User's Guide Specifications Table 5. Main connector pin out Pin Signal name Pin Signal name 50 GND 49 +5V 48 FIRSTPORTC Bit 0 47 FIRSTPORTC Bit 1 46 FIRSTPORTC Bit 2 45 FIRSTPORTC Bit 3 44 FIRSTPORTC Bit 4 43 FIRSTPORTC Bit 5 42 FIRSTPORTC Bit 6 41 FIRSTPORTC Bit 7 40 FIRSTPORTB Bit 0 39 FIRSTPORTB Bit 1 38 FIRSTPORTB Bit 2 37 FIRST[...]

Declaration of Conformity Manufacturer: Measurement C omputing Corporat ion Address: 10 Comm erce Way Suite 1008 Norton, MA 02766 USA Category: Electrical equipm ent for measurem ent, control and laboratory use. Measurement Computing Corporation declares under sole responsibility that the product CIO-DIO48H to which this declaration relates is in c[...]

Measurement Computing Corporation 10 Commerce Way Suite 1008 Norton, Massachusetts 02766 (508) 946-5100 Fax: (508) 946-9500 E-mail: info@mccdaq.com www.m cc daq .com[...]