Impex PM-3200 инструкция обслуживания

NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model PM-3200 Retain This Manual for Reference 110525 OWNER'S MANUAL PLATINUM MARCY HOME GYM PM-3200 IMPEX ® INC. 14777 DON JULIAN RD., CITY OF INDU[...]

TABLE OF CONTENTS BEFORE YOU BE GIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES ...................................................................……….. 2 HARDWARE PACK ……….....…..................................................................... ……….[...]

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipm ent. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the ma[...]

WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Base Frame and Upper Frame. If the labels are missing or illegible, please call customer ser vice at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3[...]

HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4[...]

HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5[...]

HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6[...]

ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Push two Ø 2 3/8” x 1” Rubber Bumpers (#43) onto the Guide Rods (#13) [...]

DIAGRAM 1 8[...]

STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Slide the 14 Weight Plates (#34) onto the Guide Rods (#13). Make sure the deep grooves on the Plates are all facing down and toward back of the machine. If the locking holes on the guide rods are more than 2-3 inches from the upper most, then you have installed [...]

DIAGRAM 2 10[...]

STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#6) to the U pper Frame (#4). Secure it with one 6 1/8” Front Press Axle (#37), one Ø ¾” Washer (#84), one Ø ¾” Lock Washer (#88), one M10 x 1” Allen Bolt (#73), and one Ø 2” End Cap (#47) on each end of the Axle. B.) Insert the axle on the Right Butterfly Base ( #7) into the Fr[...]

DIAGRAM 3 12[...]

STEP 4 (See Diagram 4) A.) Attach the Main Seat Support (#1) to the Front Vertical Frame (#3). Secure it with two M10 x 3 ¾” Carriage Bolts (#79), one 4 ¾” x 1 ¾” Bracket (#22), two  ¾” Washers (#84), and two M10 Aircraft Nuts (#83). B.) Attach the Seat Bracket (#20) onto the Main Seat Support. Place the Seat Pad (#38) onto Main Seat[...]

CABLE LOOP DIAGRAM 14[...]

STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 118” Upper Cable (#59) to the opening on the front of the Upper Frame (#4). Note : The Ball Stopper on the cable should be underneath the Frame. B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#69), two Ø 7/8” x 5/8” Pulley Bushings (#44), a[...]

DIAGRAM 5 16[...]

STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 110” Butterfly Cabl e (#61) onto the hook on the Right Butterfly Base (#7). B.) Draw the Cable to the right Swivel Pulley Bracket (#26). C.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#71), two Ø ¾” Washers (#84), and one M10 Aircraft N[...]

DIAGRAM 6 18[...]

STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 157” Lower Cable (#60) to the opening on the bottom of the Leg Developer (#11). B.) Attach a Pulley (#62) to the opening. Secu re it with one M10 x 2 ½” Allen Bolt (#69), two Ø 7/8” x Ø 5/8” Bushings (#44), and one M10 Aircraft Nut (#83). C.) Draw the Cable underneath the Pul[...]

DIAGRAM 7 20[...]

STEP 8 (See Diagram 8) A.) Attach a Chain (#66) to the Lower Cabl e (#60) by using a Hook (#67). Attach the Shiver Bar Handle (#19) to the Chain by us ing another Hook. Adjust the length of the Chain to obtain the desired Arm Curl exerci se. Replace Shiver Bar Handle with Ankle Strap (#68) for various exercises. Remo ve the Chain and Shiver Bar Han[...]

Set up the Lock Combination A.) The combination is pre-se t at 0-0-0 by the factory. B.) Turn the dials to 0-0-0 and ali gned to the Combination Set Up Line. C.) Pull out the shackle and turn 180 0. D.) Press down on the shackle. E.) Turn the dials (aligned to the Combination Set Up Line) to your desired combination. F.) Pull out the shackle and tw[...]

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Seat Support 1 2 Rear Base Frame 1 3 Front Vertical Frame 1 4 Upper Frame 1 5 Base Frame 1 6 Front Press Base 1 7 Right Butterfly Base 1 58 Plastic Ring 2 8 Left Butterfly Base 1 9 Right Butterfly 1 10 Left Butterfly 1 11 Leg Developer 1 12 Arm Curl Stand 1 13 Guide Rod 2 14 Selector Rod 1 15 Right Weigh[...]

PM3200 WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Front Press 30 42 54 66 78 90 102 114 126 Lat Pull 30 40 50 60 70 80 90 100 110 Butterfly 15 20 25 30 35 40 45 50 55 Low Pulley 30 40 50 60 70 80 90 100 110 Leg Developer 30 40 50 60 70 80 90 100 110 WEIGHT PLATE Station 10 11 12 13 14 Front Press 138 150 162 174 186 Lat Pull 120[...]

IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two y ears on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under th is Warranty is[...]