Impex PWR 6 инструкция обслуживания

NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruc tion Parts L ist Warranty Ordering Parts Model PWR 6 Retain This Manual for Reference 06-30-03 OWNER'S MANUAL POWERHOUSE CLUB PWR 6 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 9174[...]

TA BLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDW ARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS....[...]

IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assemble or operate your machine. In particul ar, note the follow ing safety precautions: 1. Keep children and pets away [...]

HA RDWA RE PA CK 3[...]

HA RDWA RE PA CK 4[...]

A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and A llen Wrenches NOTE: It is strongly recommended this machine be assembled by tw o or more people to avoid possible inj ury. STEP 1 (See Diagram 1) A.) Attach the Main Fram e (#1) to the Front & Rear Stabilizers (#2 & 3). Secure each end with tw o M1[...]

STEP 2 (See Diagram 2) A.) Attach f our Bushings ( #27) to a Seat Support Fr ame (#6). B.) Attach a Backrest Support (#7) to the rear of the Seat Support Fr ame (#6). Ali gn the holes and secure them w ith one M10 x 1 ¾” Al len Bolt (#37) and ∅ ¾” W asher (#42). Repeat the same procedure to instal l the other side. C.) Attach two Bushing s [...]

STEP 3 (See Diagram 3) A.) Place the Backrest Board (#14) onto the Backrest Suppor ts (#7). Secure i t wi th four M8 x 2” Al len Bolts ( #40) and ∅ 5/8” W ashers (#43). B.) Place the Seat Pad (#13) onto the Seat Support Frames (#6) . Secure it w ith four M8 x 2” Allen Bol ts (#40) and ∅ 5/8” W ashers (#43). DIAGRAM 3 7[...]

STEP 4 (See Diagram 4) A.) Attach the Leg Dev eloper (#5) to the open bracket on the Mai n Frame (#1). Secur e it with an Ax le (#17), two M 10 x ¾ ” Allen Bol ts (#36), and tw o ∅ ¾” W ashers (#42). B.) Insert one Foam Tube (#10) hal fway through the hol e on the Main Frame. Inser t two Foam Tubes halfway thr ough the holes on the Leg Deve[...]

STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#15) to the Ar m Curl Stand ( #4). Secure it with tw o M8 x 5/8” Allen Bolts ( #41) and tw o ∅ 5/8” W ashers (#43). Insert the Arm Cur l Stand into the front opening on the M ain Frame (#1) . Use the Lock Knob to hold the desir ed Arm Curl height. B.) Attach the Curl Bar Support Frame ( #11)[...]

STEP 6 (See Diagram 6) A.) Attach an Upright Beam (#49) to a Floor Stabilizer (#47). Secure it w ith tw o M10 x 2 3/4” Carri age Bolts ( #81), ∅ ¾” W ashers (#42), and M10 Ai rcraft Nuts (#44). D o not tighten the nuts and bolts yet. B.) Attach the upper end of Left Support (#50) to the Upr ight Beam. Secur e it w ith one M10 x 5/8” Allen [...]

STEP 7 (See Diagram 7) A.) Attach the Front Vertical Frame (#54) to the Rear Stabilizer (#53). Secure it wi th two M10 x 5/8” Allen Bolts ( #88) and ∅ ¾” W ashers (#42). Do not tig hten all the nuts and bolts yet. B.) Attach the Cross Br ace (#48) to the Left & Rig ht Supports (#50 & 51). Secur e each end of Cross Brace w ith two M 1[...]

STEP 8 (See Diagram 8) A.) Slide the Sl iding W eight Post (#56) onto the Rear Vert ical Frame ( #52). Slide the Sl iding Pulley Bracket (#57) onto the Fr ont Vertical Frame (#54). U se a Lock Knob (#23) to hol d the Sliding Pu lley Bracket in p osition. B.) Insert the Upper Frame (#55) into the top opening on the Fr ont Vertical Frame (#54). Attac[...]

CABLE LOOP DIAGRAM 13[...]

STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 100” Upper Cable (#68) to the opening on the front U pper Frame (#55) . Make sure the ball stopper of the Cable is under the Fr ame. B.) Attach a Pulley (#70) to the openi ng. Secure i t wi th one M10 x 2 ½” All en Bolt (#85) , two 5/8” Pulley Bushings ( #79), and one M10 Ai rcra[...]

STEP 10 (See Diagram10 & Cable Loop Diagram) A.) Attach the 268” Lower Cabl e (#69) to the Sli ding Pull ey Bracket ( #57). Attach two Small Pulley s (#71) to the Brackets. Secure them w ith two M10 x 1 ¾ ” Allen Bolts (#86), four ∅ ¾” W ashers (#42), and tw o M10 Aircraft Nuts (#44). B.) Draw the Cabl e upwar d to the opening on top [...]

DIAGRAM 10 16[...]

17[...]

18[...]

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 51 Right Suppor t 1 2 Front Stabilizer 1 52 Rear Vertical Fr am e 1 3 Rear Stabilizer 1 53 Rear Stabilizer 1 4 Arm Curl St and 1 54 Front Vert ical Fr ame 1 5 Leg Developer 1 55 Upper Fram e 1 6 Seat Support Fr am e 2 56 Sliding W eig ht Post 1 7 Backrest Suppor t 2 57 Sliding Pulley Bracke t 1 8[...]

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ( "IMPEX") warrants this produc t to be fr ee from def ects in work m anship and m ater ial, under norm al use and service conditions, for a period of two y ear s on the Fram e from the date of purc hase. T his warranty extends only to the original purc haser. IMPEX 's obligation under this W ar[...]