InFocus IN5318 инструкция обслуживания

[...]

Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the autho r. © Copyright 2011 Disclaimer The information in this document is su[...]

User’s Manual — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully be fore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector. Keep this manual for future reference. Symbols Used Warning symbols a re u se d on [...]

Preface Projector Installation Notice ¾ Place the projector in a horizontal p ositio n The tilt angle of the projector should not excee d 15 de gre es, nor should the projector b e install ed in any way other than the desktop and ceiling mou nt, ot herwise lamp li fe could decrease dramatically. ¾ Allow at least 50 cm (19.69 inch) cle ara nce aro[...]

User’s Manual Replacing the Lamp Replacing the lamp can b e hazardous if done in correctly. See — iv — Replacing the Proje ction Lamp on page 39 for clear and safe instructi ons fo r this procedure. Before replacing the lamp: ¾ Unplug the power cord. ¾ Allow the lamp to cool for about one hour. Cleaning the Projector ¾ Unplug the power cor[...]

Preface – v – Table of Contents GETTING STARTED ........................................................................................................................................................... 1 P ACKING C HECKLIST ........................................................................................................................[...]

User’s Manual — vi — A UDIO P ROBLEMS ............................................................................................................................................................. 46 H AVING THE P ROJECTOR S ERVICED ................................................................................................................[...]

IN5316HD/IN5318 – User’s Manual – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: DLP P ROJ EC TO R R EMOTE CONTROL ( B ATTER IES NOT INCLUDED ) CD-ROM (T HIS U SER ’ S M ANUAL ) VGA CABLE P OWER CORD ( VARIES PER COUNTRY ) R EGISTRATIO N C ARD Safety Booklet S AFETY[...]

User’s Manual Views of Projector Parts Front-angled View I TEM L ABEL D ESCRIP TION S EE PAGE : 1. 7 IR receiver Receives the IR si gnals from the remote control 2. Lens Projection Lens 3. Focus ring Focuses the projected ima ge 17 4. Zoom ring Enlarges the projecte d ima ge 5. 14 Elevator foot Adjusts level of projector See Top view—On-screen [...]

IN5316HD/IN5318 – User’s Manual Top view—On-screen Display (OSD) buttons – 3 – I TEM L ABEL D ESCRIP TION S EE PAGE : 1. MENU Open and exit OSD menus Navigate and change settings in the OSD Quick Menu – For Volume 2. ◄ (Left cursor) Navigate the OSD Quick Menu – For Keystone 3. ▲ (Up curso r) 4. ▼ (Down cur sor) Navigate the OSD[...]

User’s Manual Rear view 2 3 4 5 6 7 89 1 0 11 26 25 24 23 22 21 19 18 17 16 15 14 13 12 1 20 I TEM L AB E L D ESCRIPTION S EE PAGE : 1. DC 12V TRIGGER Connect a 12V screen trig ger (200 ma max) 2. AUDIO OUT Connect an AUDIO CABLE to an externa l speaker system 3. AUDIO3 (L and R) Connect the AUDIO CABLE from an input device 4. VIDEO Connect the C[...]

IN5316HD/IN5318 – User’s Manual – 5 – 17. USB Connect the USB CABLE from a computer (used for presentation slid e cont rol with the projector remote) 18. DISPLAYPORT Connect a DISPLAYPORT CABLE to a DISPLAYPORT source 19. HDMI Connect the HDMI CABLE from an HDMI device 20. VGA2 Connect the RGB CABLE from a computer or a video enabled devi c[...]

User’s Manual Bottom view I TEM L ABEL D ESCRIPTION S EE PAGE : Raise and rotate the feet to change an d fine tune the angle of the projector. 1. 14 Leveling/Elevator Feet Only use with an InFocus ceiling mount system (p/n PRJ-M NT-UNIV). See your InFocus dealer o r go to 2. Ceiling support holes www.infocusstore.com . Note: When installing, ensu[...]

IN5316HD/IN5318 – User’s Manual Remote Control Par ts Important: 1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the re mote control and the proj ector. If the path be- tween the remote contro[...]

User’s Manual – 8 – I TEM L ABEL D ESCRIP TION S EE PAGE : 1. Power ON Turn the projector on 12 2. LED indicator Only lights when the remote keys are pressed 3. Display Mode Choose a suitable preset mode for usage environm ent 4. Contrast Display the Contrast setting bar and u se the right and left keys to adjust 5. Brightness Display the Bri[...]

IN5316HD/IN5318 – User’s Manual – 9 – S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the di- rection of the arrow. 2. Insert the batteries (not included) as shown in the illustration. 3. Replace the cover. Caution: 1. Only use AA batteries (Alkali ne batteries are[...]

User’s Manual Installing or Removing the Optional Lens Caution: y Do not shake or place excessive pressure on t he projector or the lens components as the projec- tor and lens components c ontain precision parts. y Before removing or installing the lens, be sure to turn off the projector, wa it until the cooling fans stop, and turn off the main p[...]

IN5316HD/IN5318 – User’s Manual Installing the New Lens 1. Align the notches and correctly posi- tion the electrical contact pad as shown in the picture. – 11 – Note: Pin of IRIS should be in the direction as shown in the picture. 2. Rotate the lens clockwise until you feel it click into place.[...]

User’s Manual Starting and Shutting down t he Projec tor 1. Remove the lens cap. 2. Connect the power cord to the pro- jector. Connect the other end to a wall outlet. Verify that the AC Power switch on the back of the unit is turned on. When connected, the PWR LED will turn solid Red. 3. Turn on the lamp by pressing the “ ” button on the rear[...]

IN5316HD/IN5318 – User’s Manual 4. If more than one input device is connected, press the SOURCE button and use ▲▼ to scroll among devices. • VGA 1 : Analog RGB • VGA 2 : Analog RGB • B N C : Analo g / serial digital interface video inputs • HDMI : High Definition Multimedia Interface (HDMI) • DISPLAYPORT : DISPLAYPORT input • Co[...]

User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector t able or stand should be level and sturdy . • Position the projector so that it is perpendicular t o the screen. • Re move and discard the foam sp acers on the rear leveling feet before adjusting th e pro- jection angle. ?[...]

IN5316HD/IN5318 – User’s Manual Adjusting Projected Image Position Using Shift The Shift feature provides a lens shift function that can be used to adjust the position of the projected image either horizontally or vertica lly within the range detailed below. Shift is a unique system that provid es lens shift while maintaining a much higher ANSI[...]

User’s Manual Adjusting the horizontal image position With the lens in the center posit ion the horizontal image pos ition can be adjusted to the left or right by up to a maximum of 5% of the image width. Note that the maximum horiz ontal image height adjust- ment can be limited by the vertical image position. For example it is not possible to ac[...]

IN5316HD/IN5318 – User’s Manual Adjusting Zoom, Focus and Keystone 1. Use the Zoom ring to resize the projected im- age and screen size. 2. Use the Focus ring to sharpen the projected image. 3. Use the KEYSTONE buttons (on the projec- tor or the remote control) to correct im- age trapezoiding (wider top or bottom). Remote control and OSD panel [...]

User’s Manual Adjusting the Volume 1. Press the Volume but- tons (on the projector or the remote control). The volume control appears on the display. 2. Use the Vol +/- buttons (on the projector or the remote control). 3. Press the MUTE button to turn off the audio (This feature is only available on the re- mote). – 18 –[...]

IN5316HD/IN5318 – User’s Manual – 19 – O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote control cursor buttons or the projector keyp ad to navigate and make changes to the OSD. 1. To enter the O[...]

User’s Manual Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic . 2. Press the cursor ▲▼ button until Language is highlighted. 3. Press the cursor ◄► button until the language you want is selected. 4. Press the MEN[...]

IN5316HD/IN5318 – User’s Manual OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. – 21 –[...]

User’s Manual PICTURE>>Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Basic menu. Press ◄► to change values for settings. Note: Customizing the settings in PICTURE>>Basic menu is[...]

IN5316HD/IN5318 – User’s Manual PICTURE>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Advanced menu. Press ◄► to change values for settings. I TEM D ESCRIPTION Noise Reductio[...]

User’s Manual HSG Adjustment Press the ENTER/SELECT button to enter the HSG Adjustment sub menu. I TEM D ESCRIP TION Press the ◄► buttons to set the Primary Color. Notes: There are si x colors ( R / G/ B/ C/ M/ Y) to be cus tomized. Primary Color Hue Press the ◄► buttons to adjust the Hue. Saturation Press the ◄► buttons to adjust the[...]

IN5316HD/IN5318 – User’s Manual DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings. I TEM D ESCRIPTION Press the cursor ◄► button to set the Aspect Ratio. (Range[...]

User’s Manual PC Detail Adjustment Press the ENTER/SELECT button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is only available when PC input source (ana- log RGB) is selected. I TEM D ESCRIP TION Press the RE-SYNC button on the projector keypa d or the AUTO IMAGE button on the remote con[...]

IN5316HD/IN5318 – User’s Manual SETUP>>Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Basic menu. Press ◄► to change values for settings. I TEM D ESCRIP TION Press the cursor ◄► butt[...]

User’s Manual Menu Settings Press the ENTER/SELECT button to enter the Menu Settings sub menu. I TEM D ESCRIP TION Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center / Bottom-Left/ Bottom-Right. Menu Position Press the ◄► buttons to set the Menu Display timer before the OSD times out. (Range: 5sec/ 10sec/ [...]

IN5316HD/IN5318 – User’s Manual Source Press the ENTER/SELECT button to enter the Source sub menu. I TEM D ESCRIP TION VGA 1 Press the ◄► buttons to enable or disable the VGA source. VGA 2 HDMI Press the ◄► buttons to enable or di sable the HDMI source. DisplayPort Press the ◄► buttons to enable or disable the DisplayPort sou r ce. [...]

User’s Manual Lan Control Settings Press the ENTER/SELECT button to enter the Lan Control Settings sub menu. I TEM D ESCRIP TION Press the ◄► buttons to select projector remote command cont rol. (Range: RS232 / RJ45) Control By Note: thi s setting cha nges the standby powe r: RS232 <1W (Default) RJ45 <9W  Network State Press the ENTE[...]

IN5316HD/IN5318 – User’s Manual For simplicity and ease of operation, the proj ector provides diverse networking and rem ote management fea- tures. The LAN/RJ45 feature allo ws the projector to be conn ected to a net work and remotely manag e d. Available remote management controls includ e: Power On/Off, Video-Source, Bright ness and Cont rast[...]

User’s Manual Preparing Email Alerts 1. Make sure that user can access the hom epage of LAN RJ45 function by web browser (for ex- ample, Microsoft Internet Explorer v6.01/v8.0). 2. From the Homepage of LAN/RJ45, click Alert Mail Settings . 3. By default, the input boxes in Alert Ma il Settings a re blank. 4. To setup email alerts, input the follo[...]

IN5316HD/IN5318 – User’s Manual This is an optional field (for example, t he projector administrat or’s assistant).  The From field is the sender’s email address (for exam ple, the projector adm inistrator). This is a required field.  Select the alert conditions by checking the desired boxes. Note: Fill in all fields as specified. Sel[...]

User’s Manual SETUP>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Advanced menu. I TEM D ESCRIP TION Press the ENTER/SELECT button to enter the Audio sub menu. See Audio on page Audio [...]

IN5316HD/IN5318 – User’s Manual Audio Press the ENTER/SELECT button to enter the Audio sub menu. I TEM D ESCRIP TION Volume Press the ◄► buttons to adjust the audio Volume. Treble Press the ◄► buttons to adjust the audio Treble. Bass Press the ◄► buttons to adjust the audio Bass. Mute Press the ◄► buttons to turn on or off the i[...]

User’s Manual Lamp Press the ENTER/SELECT button to enter the Lamp sub menu. I TEM D ESCRIP TION Lamp Mode Press the ◄► buttons to adjust lamp brightness. Press the ENTER/SELECT button to reset the Lamp Hour after the lamp is re pla ced. Reset Lamp Timer Lamp Hour Displays the number of hours the lamp has b een in use. HDMI Press the ENTER/SE[...]

IN5316HD/IN5318 – User’s Manual Closed Caption Press the ENTER/SELECT button to enter the Closed Caption sub menu. I TEM D ESCRIPTION Closed Caption En- able Press the ◄► buttons to turn on o r off Closed Caption. Caption Version Press the ◄► buttons to select the Caption Version. Presentation Timer The Presentation Timer func tion can [...]

User’s Manual STATUS Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the STATUS Menu . I TEM D ESCRIP TION Source Displays the activated input source. Resolution Displays the nativ e resolution of input source. Lamp Hour Displays the number of hours the lamp has b een in use. Firmware Version Displays th[...]

IN5316HD/IN5318 – User’s Manual – 39 – M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. Be sure to use the InFocus lamp module de- signed for this projector. You can order new lamps from www.infocusstore.com (i n select areas), your retailer or your dealer. Only genuine InFoc[...]

User’s Manual 4. Loosen the captive screw on the lamp cover. 5. Pull up and remove the cover. 6. Use a screwdriver to re- move the two captive screws from the lamp module. 7. Pull out the lamp module. – 40 –[...]

IN5316HD/IN5318 – User’s Manual 8. Reverse steps 1 to 7 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws. 9. Turn on the projector and r[...]

User’s Manual – 42 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 60 minutes before cleaning. Failure to do so could result in a severe burn. 2. Use only a dampened cloth when cleaning. Do not allow water to en[...]

IN5316HD/IN5318 – User’s Manual – 43 – T ROUBLESHOOTING Common Problems and Sol utions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, contact InFocus at www.infocus.com/support . Often the problem is traced to something as simple as a loose connection. C hec[...]

User’s Manual – 44 – LED Error Messages PWR LED READY LED TEMP LED E RROR C ODE M ES SAGES Green Red Red Red Standby — ON — — Start-up/Cool Down ON — flashing — Overheating — — — ON Thermal Break Sensor er ror — 7 blinks — — Lamp Error 5 blinks — — — Burner Fan error 6 blinks — 1 blinks — System Fan error 6 bli[...]

IN5316HD/IN5318 – User’s Manual – 45 – Problem: The image is flat with no contrast Adjust the Contrast setting in the PICTURE >> Basic menu of the OSD. Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the PICT URE >> Advanced menu of the OSD. Lamp Probl[...]

User’s Manual – 46 – Audio Problems Problem: There is no sound 1. Adjus t the volume on the remote control. 2. Adjust the volume of the audio source. 3. Che ck the audio cable connection. 4. Disco nnect audio out cable. 5. Test the sou rce audio output with other speakers. 6. Have the p rojector serviced. Problem: The sound is distorted 1. Ch[...]

IN5316HD/IN5318 – User’s Manual – 47 – HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announ ced that cables would be tested as Standard or High- Speed cables. ˙ Standa rd (or “category 1”) HDMI cabl es have b een tested to perform at speed s[...]

User’s Manual – 48 – S PECIFICATIONS Specifications Model IN5316HD IN5318 TI DMD 1080P 0.65” TI DMD WUXGA 0.67” Display ty pe 1920x1080 1920x1200 Native Resolution Projection distance 1.5 meters ~ 7 meters ( 4.92 ft ~ 22.97 ft ) (standard lens) Projection screen size 35.1”~205” (89cm ~5 21cm) 36.1”~211”(92cm~536 cm) (standard lens[...]

IN5316HD/IN5318 – User’s Manual Projection Distance vs. Projection Si ze (1080P) Projection Distance A Image Height Projection Distance and Size Table Standard projection lens: TR: 1.54– 1.93; offset=10% IN5316HD T ELE W IDE 1.71/ 67.3 3.42/ 134.6 4.27/ 168.2 8.55/ 336.4 1.70/ 67.1 3.41/ 134.2 6.82/ 268.4 10.23/ 402.7 Distance (m/inch) Diagon[...]

User’s Manual Projection Distance vs. Projection Si ze (WUXGA) Projection Distance A Image Height Projection Distance and Size Table Standard projection lens: TR: 1.54–1.93; offset=5% IN5318 T ELE W IDE Distance (m/inch) 1.66/65.5 3.33/130.9 4.16/163. 7 8.31/327.3 1.66/65.3 3.32/ 130.6 6.63/261.2 9.95/391.8 Diagonal (inch/ft) 40/3.3 80/6.7 100/[...]

IN5316HD/IN5318 – User’s Manual – 51 – Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. S IGNAL R ESOLUTION H-S YN C (KH Z ) V-S YNC (H Z ) C OMPOSIT E / S-V IDEO VGA 1/2 /RGBHV ( ANALOG ) HDMI ( DIGITAL ) DP ( DIGITAL ) NTSC — 15.734 60.0[...]

User’s Manual – 52 – S IGNAL R ESOLUTION H-S YN C (KH Z ) V-S YNC (H Z ) C OMPOSIT E / S-V IDEO VGA 1/2 /RGBHV ( ANALOG ) HDMI ( DIGITAL ) DP ( DIGITAL ) 720p 37.5 50.0 — O O O 720p 45.0 60.0 — O O O 1080i 33.8 60.0 — O O O 1080i 28.1 50.0 — O O O 1080p 27 24.0 — O O O 1080p 28.13 25.0 — O O O 1080p 33.75 30.0 — O O O 1080p 67.5[...]

IN5316HD/IN5318 – User’s Manual Projector Dimensions – 53 –[...]

User’s Manual – 54 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These lim its are designed to provide reasonable protection against harmful interference when the equipm ent is operated in a commercial environment. [...]