Integra DTR-7.8 инструкция обслуживания

DTR-7.8 Instr uction Manual AV Receiv er DTR-7.8_En.book Page 1 Friday, May 9, 2008 1:56 PM[...]

2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not install near an y heat [...]

3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The A C fuse inside the unit is not user - serviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit.. 3. Care —Occasiona[...]

4 Precautions —Continued F or British models Replacement and mounting of an A C plug on the po wer supply cord of this unit should be performed only by qualified service personnel. IMPOR T ANT The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Li ve As the colours of the wires in the mains lead o[...]

5 Contents Features ............................................................ 6 Supplied Accessories ...................................... 7 Multiroom Capability ........................................ 8 Getting to Know the AV Receiver ................... 9 Front Panel ................................................................... 9 Displ[...]

6 Features Amplifier • 7-channel amplifier • 130 watts minimum continuous po wer per channel, 8 ohm loads, 2 channels driv en from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.08% (FTC) • Linear Optimum Gain V olume Circuitry •P o wered Zone 2 capability • Bi-amp capability for front speakers • WRA T (W ide Range Amp[...]

7 Features —Continued *9 ©2005 SIRIUS Satellite Radio Inc. “SIRIUS, ” SiriusConnect, the SIRIUS dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. A vailable only in the contiguous United States (excluding Alaska and Hawaii) and Canada. *10 Manufactured under license from Audysse y Laboratories. U.S. and foreign [...]

8 Multir oom Capability Y ou can use three speaker systems with this A V receiver —a surround-sound speaker system (up to 7.1 channels) in your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it, and another stereo speaker system in a third room that we call Zone 3 (external po wer amplifier required). And, y[...]

9 Getting to Kno w the A V Receiver The actual front panel has various logos printed on it. They are not sho wn here for clarity . For detailed information, see the pages in parentheses. A Standby/On b utton (43) Sets the A V receiver to On or Standby . B Standby indicator (43) Lights up when the A V receiver is on Standby and flashes while a sign[...]

10 Getting to Know the A V Receiver —Continued E Zone 3 indicator (115) Flashes when Zone 3 is being set. Lights up when Zone 3 is on. F Remote-control sensor (14) Receiv es control signals from the remote controller . G Stereo button (82) Selects the Stereo listening mode. H Listening Mode [ ]/[ ] buttons (82) Select the listening modes. I Displ[...]

11 Getting to Know the A V Receiver —Continued For detailed information, see the pages in parentheses. 1 Speaker/channel indicators (87) Indicate the speaker configuration and channels used by the current input source. – : A box is displayed for each speaker that’ s set in the Speaker Configuration. No box appears for speakers that are set [...]

12 Getting to Know the A V Receiver —Continued A REMO TE CONTROL This (Remote Interacti ve) jack can be con- nected to the jack on another -capable Inte- gra/Onkyo component for remote and system control. To use , you must make an analog audio connec- tion (RCA) between the A V receiver and the other component, ev en if they are connected digital[...]

13 Getting to Know the A V Receiver —Continued N IR IN A/B and OUT A commercially av ailable IR recei ver can be con- nected to the IR IN A or B jack, allo wing you to control the A V receiver while you’ re in Zone 2, or control it when it’ s out of sight, for e xample, installed in a cabinet. A commercially av ailable IR emitter can be con- [...]

14 Remote Contr oller Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion. • Expired batteries should[...]

15 Remote Controller —Continued As well as the A V receiver, you can also use the remote controller to control your other A V components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the Remote Mode buttons. ■ Receiver/T ape Mode In Receiv er/T ape mode, you can control th[...]

16 Remote Controller —Continued For detailed information, see the pages in parentheses. A Standby b utton (43) Sets the A V receiver to Standby . B On button (43) T urns on the A V receiv er. C Input Selector buttons (60) Used to select the input source. D Macro b uttons (123) Used with the Macro function. E Dimmer button (79) Adjusts the display[...]

17 Remote Controller —Continued To set the remote controller to D VD mode, pr ess the [D VD] Remote Mode button. A Standby b utton Sets the D VD player to Standby . B On button T urns on the D VD player . C Number buttons Used to enter title, chapter , and track numbers, and to enter times for locating specific points. D T op Menu button Selects[...]

18 Remote Controller —Continued To control an Integra/Onky o CD player , MD recorder , or CD recorder , or a CD or MD player/r ecorder made by another manufacturer , press the [CD] Remote Mode b utton to select the CD/MD/CDR remote contr oller mode. In order to control an Onkyo MD recorder or CD recorder , or a component made by another manufactu[...]

19 Remote Controller —Continued Dock mode is for controlling an Apple iPod in an Onk yo RI Dock. When Using an RI Dock: • Connect the RI Dock to the T APE IN or GAME/TV IN L/R jacks. • Set the RI Dock’ s RI MODE switch to HDD or HDD/DOCK. • Set the A V receiver’ s Input Display to DOCK (see page 49). • When operating a DS-A1 RI Dock, [...]

20 Connecting Y our Speakers Thanks to the A V receiver’ s superb capabilities, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie theater or concert hall. Y ou can enjoy D VDs featuring Dolby Digital or DTS. W ith analog or digital TV , you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo[...]

21 Connecting Y our Speakers —Continued Speaker Configuration F or the best surround-sound e xperience, you should con- nect sev en speakers and a po wered subwoofer . The following table sho ws which channels you should use based on the number of speakers you ha ve. * If you’ re using only one surround back speaker , connect it to the SURR B [...]

22 Connecting Y our Speakers —Continued Speaker Connection Precautions Read the following before connecting your speak ers: •Y ou can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more b ut less than 6, be sure to set the speaker impedance to 4 ohms (see page 44). If [...]

23 Connecting Y our Speakers —Continued The FR ONT L/R and SURR B A CK L/R terminal posts can be used with front speakers and surround back speakers respecti vely , or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing impro ved bass and treble performance. • When bi-amping is us[...]

24 Connecting Antennas This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and ho w to connect commercially av ailable outdoor FM and AM antennas. The A V receiver w on’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner . The supplied indoor FM antenna [...]

25 Connecting Antennas —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft. •F or best results, install the outdoor FM an[...]

26 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections. Optical Digital Jacks The A V receiver’ s optical digital jacks have shutter -type cov ers that open when an optical p[...]

27 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiver. The A V receiver supports se veral connection formats for compatibility with a[...]

28 Connecting Y our Components —Continued ■ HDMI Monitor Setting Set to No W ith the HDMI Monitor setting set to No (see page 45), video input signals flow through the AV receiv er as shown, with composite video and S-V ideo sources being upcon v erted for the component video output. Use this setting if you connect the A V r eceiver’ s COMPO[...]

29 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your TV or listen in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection or . (T o record or listen in Zone 2 or Zone 3 as well, use and , or and .) If your TV has no audio outputs, connect an audio output from your VCR or cabl[...]

30 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from a D VD or listen in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection or . (T o record or listen in Zone 2 or Zone 3 as well, use and , or and .) • If your D VD player has main left and right outputs and multichannel left a[...]

31 Connecting Y our Components —Continued Hooking Up the Multichannel Input If your D VD player supports multichannel audio formats such as D VD-Audio and SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiver’ s multichannel input. Use a multichannel analog audio cable, or sev eral normal audio cables, to [...]

32 Connecting Y our Components —Continued W ith this hookup, you can use the tuner in your VCR or D VR to listen to your fa vorite TV programs via the A V receiver, which is useful if your TV has no audio outputs. •W ith connection , you can listen to the VCR or D VR in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection or . ([...]

33 Connecting Y our Components —Continued Notes: • The A V receiv er must be turned on for recording. Recording is not possible while it’ s on Standby . • If you want to record directly from your TV or another video source without going through the A V receiver , connect the audio and video outputs from your TV or other video component dire[...]

34 Connecting Y our Components —Continued W ith this hookup, you can use your satellite or cable receiv er to listen to your fav orite TV programs via the A V receiver, which is useful if your TV has no audio outputs. •W ith connection , you can listen to and record audio from the video source or listen in Zone 2 or Zone 3. •T o enjoy Dolby D[...]

35 Connecting Y our Components —Continued About HDMI Designed to meet the increased demands of digital TV , HDMI (High Definition Multimedia Interface) is a ne w digital interface standard for connecting TVs, projectors, DVD players, set-top box es, and other video components. Until now , sev eral separate video and audio cables hav e been requi[...]

36 Connecting Y our Components —Continued Making HDMI Connections ■ Video Signals Digital video signals receiv ed by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV . Composite video, S-V ideo, and component video sources can be upcon v erted for the HDMI output. See “V ideo Con- nection Formats” on page 27 for [...]

37 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your game console or listen in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection . (T o record or listen in Zone 2 or Zone 3 as well, use and .) Connecting a Game Console Connection A V receiver Signal flow Game console Pict[...]

38 Connecting Y our Components —Continued Connecting a Camcorder or Other A V Component Connection A V receiver Signal flow Camcorder A UX 2 Input S Video ⇐ S-Video output A UX 2 Input Video ⇐ Composite video output A UX 2 Input L/R ⇐ Analog audio L/R output A UX 2 Input Digital ⇐ Digital optical output Step 1: Video Connection Choose a [...]

39 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from the CD player or listen in Zone 2 or Zone 3. •T o connect the CD player digitally , use connection or . (T o record or listen in Zone 2 or Zone 3 as well, use and , or and .) The A V receiver’ s PHONO IN is designed for use with a moving ma[...]

40 Connecting Y our Components —Continued •W ith connection , you can play and record or listen in Zone 2 or Zone 3. •T o connect the recorder digitally for playback, use connections and , or and . •T o connect the recorder digitally for recording, use connection . If you want to use a more po werful power amplifier and use the A V receive[...]

41 Connecting Y our Components —Continued ■ If Y our iPod Supports Video: Connect your RI Dock’ s audio output jacks to the AV receiv er’ s GAME/TV IN L/R jacks, and connect its video output jack to the A V receiver’ s GAME/TV IN V jack. (Onkyo DS-A2 hookup sho wn below .) ■ If you ha ve an Onkyo DS-A1 RI Doc k • Connect its video out[...]

42 Connecting Y our Components —Continued W ith (Remote Interactive), you can use the follo wing special functions: Auto P o wer On/Standby When you start playback on a component connected via , if the A V receiv er is on Standby , it will automatically turn on and select that component as the input source. Similarly , when the A V receiv er is s[...]

43 T urning On the A V Receiver Standby/On Standby/On + - On Standby TV Input TV CH TV VOL -- / --- 10 11 12 D.TUN +10 0 Clear 123 456 789 Input Selector VCR / DVR CBL / SAT DVD Tape Tuner CD Phono Game / TV Macro 12 3 VCR DVD CDR/MD CD Zone 2 Remote Mode Dimmer Tape/AMP Sleep Receiver TV Dock Cable SAT Zone 3 AUX 1 AUX 2 On Receiver Standby Standb[...]

44 Fir st Time Setup This section explains the settings that you need to make before using the A V recei ver for the very first time. If the impedance of any speaker is 4 ohms or more b ut less than 6, set the Speaker Impedance to 4 ohms. If you’ ve connected your front speak ers to the FR ONT and SURR B A CK terminal posts for bi-amping, you mu[...]

45 First Time Setup —Continued If you connect your TV to the COMPONENT VIDEO MONITOR OUT 1 or COMPONENT VIDEO MON- ITOR OUT 2/ZONE 2 OUT , set the HDMI Monitor set- ting to No so that the onscreen setup menus are displayed and composite video and S-V ideo sources are upcon- verted and output by the COMPONENT VIDEO MON- ITOR OUT 1 and COMPONENT VI[...]

46 First Time Setup —Continued Notes: • See page 27 for charts showing ho w the HDMI Moni- tor setting affects the video signal flo w through the A V receiv er. • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. If you connect a video component to an HDMI IN, you must assign that [...]

47 First Time Setup —Continued Notes: • Each HDMI IN cannot be assigned to more than one input selector . • For composite video, S-V ideo, and component video upcon version f or the HDMI OUT , the HDMI Monitor setting must be set to Y es (see page 45). See page 27 for more information on video signal flow and upcon version. • When an HDMI [...]

48 First Time Setup —Continued If you connect a video component to a COMPONENT VIDEO IN, you must assign that input to an input selector . F or example, if you connect your D VD player to COMPONENT VIDEO IN 3, you must assign COM- PONENT VIDEO IN 3 to the D VD input selector . By default, the D VD input selector is assigned to COM- PONENT VIDEO I[...]

49 First Time Setup —Continued Notes: • F or composite video and S-V ideo upcon v ersion for the COMPONENT VIDEO MONITOR OUT 1 or 2, the HDMI Monitor setting must be set to No (see page 45). See page 27 for more information on video signal flow and upcon version. • This procedure can also be performed on the A V receiv er by using its [Setup[...]

50 First Time Setup —Continued If you connect a component to a digital audio input, you must assign that input to an input selector . F or example, if you connect your CD player to OPTICAL IN 2, you must assign OPTICAL IN 2 to the CD input selector . These are the default assignments. Digital Input Setup Input selector Audio input DV D C O AX1 VC[...]

51 First Time Setup —Continued Notes: • Only FR ONT can be assigned to the A UX 2 input selector . • The TUNER input selector cannot be assigned and is fixed at the “- - -” option. • When an HDMI IN is assigned to an input selector in “HDMI V ideo Setup” on page 46, this input assign- ment is automatically set to the same HDMI IN. [...]

52 First Time Setup —Continued If you connect a component to the A V receiver’ s analog multichannel input, you must assign that input to an input selector . F or example, if you connect your D VD player to the MUL TI CH input, you must assign it to the D VD input selector . Notes: •T o listen to the component connected to the multi- channel [...]

53 First Time Setup —Continued W ith the supplied speaker setup microphone, Audyssey MultEQ XT can measure the number of speakers con- nected, their sizes, crossov er frequencies, and distances from the listening position and calculate the optimal speaker settings for you automatically . Before using this function, connect and position all of you[...]

54 First Time Setup —Continued 1 T urn on the A V receiver and the connected TV . On the TV , select the input to which the AV receiv er is connected. 2 Place the setup microphone at the 1st measurement position, and connect it to the Setup Mic jack. Notes: • Make sure the microphone is hori- zontal. • If there’ s an obstacle between the mi[...]

55 First Time Setup —Continued Notes: • When the automatic speaker setup is complete, the Equalizer Settings (page 101) will be set to Audyssey . •Y ou can cancel the automatic speaker setup at any point in the procedure simply by disconnecting the setup microphone. Error Messa ges During the automatic speaker setup, one of the follo wing err[...]

56 First Time Setup —Continued Speaker Detect Error This message appears if a speaker is not detected. “Y es” means that a speaker was detected. “No” means that no speaker was detected. Check your speak er connections and retry , or cancel the automatic speaker setup. One of the front speakers has not been detected. One of the surround sp[...]

57 First Time Setup —Continued Revie wing the Results Changing the Speaker Settings Manuall y In some cases, the measurements taken by the automatic speaker setup may not provide usable results. If running the speaker setup a second time doesn’ t help, you’ll hav e to set the speaker settings manually (see pages 96–101). Notes: •F or THX-[...]

58 First Time Setup —Continued For the onscreen setup menus to display properly , you must specify the TV system used in your area. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. TV Format Setup (not North American models) 1 Press the [Receiver] button, f ol- lowed b y the [...]

59 First Time Setup —Continued For AM tuning to work properly , you must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. AM Frequency Step Setup (on some m[...]

60 Pla ying Y our A V Components Basic A V Receiver Operation 3 1 + - On Standby TV Input TV CH TV VOL -- / --- 10 11 12 D.TUN +10 0 Clear 123 456 789 Input Selector VCR / DVR CBL / SAT DVD Tape Tuner CD Phono Game / TV Macro 12 3 VCR DVD CDR/MD CD Zone 2 Remote Mode Dimmer Tape/AMP Sleep Receiver TV Dock Cable VOL CH Disc Album + - Enter T o p M e[...]

61 Listening to the Radio W ith the built-in tuner , you can enjoy AM and FM radio stations and store your fa vorite stations as presets for easy selection. T uning into AM/FM Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator also appears. ■ M[...]

62 Listening to the Radio —Continued ■ T uning into Stations by Frequenc y Y ou can tune into AM and FM stations directly by enter- ing the appropriate frequency . Displaying AM/FM Radio Inf ormation Note: • When you select a preset with a custom name (see page 104), its name is displayed instead of the band and frequency . 1 Press the [Recei[...]

63 Listening to the Radio —Continued RDS only works in areas where RDS broadcasts are av ailable. When tuned to an RDS station, the RDS indi- cator appears. ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was de veloped by the European Broadcasting Union (EBU) and is a vail- able in m[...]

64 Listening to the Radio —Continued Displaying Radio T ext (R T) When tuned to an RDS station that’ s broadcasting te xt information, the text can be displayed. Notes: • The message “W aiting” may appear while the A V receiv er waits for the R T information. • If the message “No T ext Data” appears on the display , no R T informati[...]

65 Listening to the Radio —Continued Note: Hardware and required monthly subscription sold sepa- rately . Other fees and taxes, including a one-time activ a- tion fee may apply . Subscription fee is consumer only . All fees and programming subject to change. Channels with frequent explicit language are indicated with an XL. Channel blocking is av[...]

66 Listening to the Radio —Continued Selecting XM Satellite Radio Signing Up for XM Satellite Radio Once you hav e installed the XM Mini-T uner and Home Dock, you are ready to subscribe to XM Satellite Radio. Y ou’ll need a major credit card and your XM Radio ID. There are three places you can find your 8-character XM Radio ID: 1. On the XM Mi[...]

67 Listening to the Radio —Continued Notes: • RADIO ID cannot be selected in Category Search mode. Y ou must select Channel Search mode (see right column). • The following letters are not used in XM Satellite Radio IDs: I, O, S, F . • XM Satellite Radio will transmit a special signal to your A V receiv er to activ ate the full channel lineu[...]

68 Listening to the Radio —Continued Selecting Channels on the A V receiver: Selecting the Previous Channel: Displaying XM Radio Inf ormation The following information can be displayed: Notes: • If the category , artist, or song title is not av ailable, “- - -” will be displayed instead. • The listening mode is not displayed when Zone 2 o[...]

69 Listening to the Radio —Continued Notes: • So long as the signal strength is good, you can enjoy XM Radio by using either satellite or terrestrial recep- tion. •T errestrial signals are only av ailable in certain areas. • The XM information is only displayed when the Sat- ellite Radio mode is set to XM or XM/SIRIUS (see page 66). • If [...]

70 Listening to the Radio —Continued Note: Hardware and required basic monthly subscription sold separately . Installation costs and other fees and taxes, including a one-time activ ation fee may apply . Subscrip- tion fee is consumer only . All fees and programming subject to change. What is SIRIUS Satellite Radio? Simply The Best Radio on Radio[...]

71 Listening to the Radio —Continued Setting the Satellite Radio Mode Before you can listen to SIRIUS Satellite Radio, you must set the Satellite Radio mode to SIRIUS. Selecting SIRIUS Satellite Radio 1 Press the [Receiver] Remote Mode button, f ollowed b y the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons [...]

72 Listening to the Radio —Continued Signing Up for SIRIUS Satellite Radio Before you can use SIRIUS Satellite Radio, you must first sign up for an account. Y ou’ll need a major credit card and your SIRIUS Satellite Radio ID, which you can get from the A V receiver, as e xplained below , or from the SiriusConnect Home tuner package. Note: •Y[...]

73 Listening to the Radio —Continued Notes: • If you select an unav ailable channel, “INV ALID CHANNEL” appears on the display . • If you select a channel that you are not subscribed to, “CALL SIRIUS” appears on the display . • Channels that are locked must be unlocked before you can listen to them. See “Parental Lock” on right [...]

74 Listening to the Radio —Continued Notes: • While a channel is locked, it cannot be selected for listening. •T o unlock a channel, you must enter the correct PIN number and change it to Unlocked in step 6. Changing the PIN Number 4 Press the [D .TUN] button, and then use the number b uttons to enter the 4-digit PIN number . Or Use the Left [...]

75 2 Use the Up and Down [ ]/[ ] buttons to select “4. Sour ce Setup, ” and then press [Enter]. The Source Setup menu appears. Note: If the Satellite Radio mode is set to None or XM (see page 71), the “5. SIR- IUS Parental Lock” item is not a vail- able. 3 Use the Up and Down [ ]/[ ] buttons to select “5. SIRIUS P arental Lock, ” and th[...]

76 Listening to the Radio —Continued Displaying SIRIUS Satellite Radio Information The following information can be displayed: Notes: • If the category , artist/composer , or song title is not av ailable, “- - -” will be displayed instead. P ositioning the SiriusConnect Home Antenna Y ou can check the strength of the SIRIUS Satellite Radio [...]

77 Listening to the Radio —Continued Notes: • So long as the signal strength is good, you can enjoy SIRIUS Satellite Radio by using either satellite or ter- restrial reception. •T errestrial signals are only av ailable in certain areas. • The SIRIUS information on the Satellite Radio screen is only displayed when the Satellite Radio mode is[...]

78 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fav orite AM, FM, XM, and SIRIUS radio stations. Note: •Y ou can name your radio presets for easy identifica- tion (see page 104). Selecting Presets Deleting Presets Presetting AM, FM, XM, and SIRIUS Stations 1 T une into the AM, FM, XM, or SIR- IUS station y[...]

79 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can adjust the volume of each speaker while listen- ing to an input source. These temporary adjustments are cancelled when the A V receiver is set to Standby . Notes: •Y ou cannot use this function whil[...]

80 Common Functions —Continued W ith the sleep timer , you can set the A V receiver so that it turns off automatically after a specified period. To cancel the sleep timer , press the [Sleep] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [Sleep] b utton. Note that if you press the [Sleep] b u[...]

81 Common Functions —Continued If you connect a component to more than one audio input, such as a D VD player connected to analog, digital, multichannel, and HDMI inputs, you can use the [Audio Sel] button to select which audio input you w ant to use to listen to that component. Normally , the A V receiv er detects the format of digital input sig[...]

82 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 87. Selecting on the A V Receiver ■ [Stereo] button This button selects the Stereo listening mode. ■ Listening Mode [ ]/[ ] buttons Pressing these buttons repeatedly c ycles through all of the listening modes that can be used wit[...]

83 Using the Listening Modes —Continued Analog and PCM Sources Listening Modes A v ailable for Eac h Source Format Button Source f ormat PCM Multi channel analog Multichannel PCM 32–96 kHz 176.4/ 192kHz* 1 32–96 kHz 176.4/192 kHz *1 *1. DVD-Audio discs output multichannel 176.4/192 kHz PCM only via HDMI. except */2 */2 2ch 1/0, 1+1 Multichann[...]

84 Using the Listening Modes —Continued DSD , Dolby Digital, and Dolb y Digital Plus Sources Button Source f ormat DSD *1 *1. In listening modes other than DSD Direct, DSD sources are converted and handled as PCM. Dolby D Dolby Digital Plus Multichannel Multichannel 2ch 1/0, 1+1 Multichannel 2ch 1/0, 1+1 3/2 2ch e xcept */2 */2 except */2 */2 Med[...]

85 Using the Listening Modes —Continued T rueHD and DTS Sources Button Source f ormat T rueHD *1 *1. 192 kHz TrueHD sources are processed as 192 kHz/2-channel audio signal, regardless its number of channels. DTS, DTS96/24 DTS-ES Discrete/ Matrix Multichannel 2ch 1/0, 1+1 Multichannel 2ch 1/0 except */2 */2 except */2 */2 Media Listening Mode Blu-[...]

86 Using the Listening Modes —Continued DTS-HD Sources Button Source f ormat DTS-HD High Resolution DTS-HD Master Audio *1 *1. 192 kHz DTS-HD Master Audio sources are processed at 96 kHz. Multichannel 2ch 1/0 Multichannel 2ch 1/0 except */2 */2 except */2 */2 Media Listening Mode Blu-ray , HD D VD Blu-ray , HD D VD [Direct] Direct ✔✔✔✔✔[...]

87 Using the Listening Modes —Continued The A V receiver’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal processing, providing high-fidel- ity reproduction. All of the sour[...]

88 Using the Listening Modes —Continued DTS-HD Master Audio Designed to take full adv antage of the additional storage space offered by the ne w Blu-ray and HD D VD disc for- mats, this new DTS format of fers up to 7.1 discrete chan- nels of uncompressed digital audio with 96 kHz/24-bit sampling rate and signal resolution. The A V receiver suppor[...]

89 Recor ding This section explains ho w to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected D VDs cannot be recorded. • Sources connected to the analog multichannel input cannot be recorded. •V arious restrictions apply [...]

90 Onscreen Setup Menus The onscreen setup menus appear on the connected TV and pro vide a con ve- nient way to change the A V receiv er’ s v arious settings. Settings are organized into eight categories on the main menu , most containing a submenu . The following map sho ws ho w the setup menus are organized. Use the page numbers to locate infor[...]

91 Adjusting the Listening Modes W ith the Re-EQ function, you can compensate a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing. This function can be used with the following listening modes: Dolby Digital, Dolby Digital EX, Dolby Pro Logic II Movie, Dolby Pro Logic IIx Mo vie, DTS, DTS- ES, DTS[...]

92 Adjusting the Listening Modes —Continued W ith the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. T one Control Settings Y ou can adjust the tone (bass and treble) of the front, center , surround, and surround back speakers indi vidu- ally . For the subwoofer , you can adjust the bass. ■ Bass Y[...]

93 Adjusting the Listening Modes —Continued Direct Setting Delay Enable ■ DSD This setting determines whether or not DSD (SA CD) audio signals are passed through the DSP for A/V Sync, delay , etc., processing when the Direct listening mode is selected. No: DSD signals are not processed by the DSP . Y es: DSD signals are processed by the DSP . M[...]

94 Adjusting the Listening Modes —Continued Dolby Digital Settings ■ Dolby EX This setting determines how Dolby EX signals are han- dled. A uto: When the source is Dolby EX, you can select the Dolby EX or THX Surround EX listening mode. Manual: When the source is Dolby EX, you can select any of the listening modes compatible with this format (e[...]

95 Adjusting the Listening Modes —Continued Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. 3 Use the Up and Down [ ]/[ ] buttons to select an input selec- tor , and then press [Enter]. The audio formats supported by that input selector appear . If the input selector is assi[...]

96 Ad v anced Setup This section explains items on the Speaker Config menu. Some of the speaker settings are set automatically by the Automatic Speaker Setup function (see page 53). Speaker Settings See “Speaker Settings” on page 44. Speaker Configuration W ith the Speaker Configuration settings, you can specify which speakers are connected [...]

97 Adv anced Setup —Continued 5 Use the Up and Down [ ]/[ ] buttons to select “Front, ” and then use the Left and Right [ ]/[ ] buttons to select a crosso ver frequency . Note: • Fixed at Full Band if Subwoofer (step 4) is set to No. 6 Use the Up and Down [ ]/[ ] buttons to select “Center , ” and then use the Left and Right [ ]/[ ] butt[...]

98 Adv anced Setup —Continued Low-P ass Filter f or the LFE Channel W ith this setting, you can specify the cutoff frequenc y of the LFE channel’ s lo w-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel. *If you’ re using THX-certified speak ers, select 80 Hz (THX). Do[...]

99 Adv anced Setup —Continued Speaker Distance W ith the Speaker Distance settings, you can specify the distance from each speaker to the listening position. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. 1 Press the [Receiver] Remote Mode button, f ollowed b y the [Setup] [...]

100 Adv anced Setup —Continued Speaker Level Calibration W ith the Lev el Calibration settings, you can adjust the lev el of each speaker while listening to the test tone so that the volume of each speak er is the same at the listen- ing position. Note: • The test tone is output at the standard lev el for THX, which is 0 dB (absolute volume set[...]

101 Adv anced Setup —Continued Equalizer Settings W ith the Equalizer settings, you can adjust the tone of speakers indi vidually with a 15-band equalizer . The v ol- ume of each speaker can be set on page 100. 1 Press the [Receiver] Remote Mode button, f ollowed b y the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ [...]

102 Adv anced Setup —Continued Notes: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. • The Equalizer settings hav e no effect on 176.4/ 192 kHz input signals. THX A udio Setup W ith the Surr Back Sp Spacing setting, you can specify the distance between your surround back speake[...]

103 Adv anced Setup —Continued Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. This section explains items on the Source Setup menu. Items can be set individually for each input selector . 5 Use the Up and Down [ ]/[ ] buttons to select “THX Sub- woof er , ” and use the [...]

104 Adv anced Setup —Continued IntelliV olume W ith IntelliV olume, you can set the input level for each input selector individually . This is useful if one of your source components is louder or quieter than the others. Use the Up and Down [ ]/[ ] b uttons to select an input selector , and use the Left and Right [ ]/[ ] but- tons to set the lev [...]

105 Adv anced Setup —Continued Notes: •T o store a name, you must select “OK” and press [Enter] in step 7, otherwise it will not be sav ed. •Y ou cannot enter a custom name for XM or SIRIUS radio presets. • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. Satellite Radio This[...]

106 Adv anced Setup —Continued This section explains items on the Miscellaneous menu. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. V olume Setup ■ V olume Display W ith this setting, you can choose how the v olume lev el is displayed. Absolute: Display range is Min, 0.5[...]

107 Adv anced Setup —Continued ■ Po wer On V olume This setting determines what the volume will be each time the A V receiver is turned on. When the V olume Display preference is set to Absolute, the range is Last, Min, 1 to Max. When it’ s set to Rela- tiv e, the range is Last, – ∞ dB, –81 dB to +18 dB. To use the same volume le vel as[...]

108 Adv anced Setup —Continued This section explains items on the Hardware menu. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. Remote Control ■ Remote ID When sev eral Integra/Onk yo components are used in the same room, their remote ID codes may ov erlap. T o dif- feren[...]

109 Adv anced Setup —Continued T uner ■ AM Freq Step (on some models) See “ AM Frequency Step Setup (on some models)” on page 59. ■ Satellite Radio (on North American model) If you connect an XM Satellite Radio antenna or SIRIUS Satellite Radio antenna to the A V receiver (both sold sep- arately), set this setting to XM or SIRIUS respecti[...]

110 Adv anced Setup —Continued • HDMI power control only w orks with HDMI-compat- ible components that support it and may not work properly with some components due to their settings or compatibility . • When set to Enable, the A V receiver consumes more power . • When set to Enable, the A V receiver enters Ready mode when set to Standby , [...]

111 Zone 2 and Zone 3 In addition to your main listening room, you can also enjoy playback in two other rooms, or as we call them, Zone 2 and Zone 3. And, you can select a dif ferent source for each room. There are two ways you can connect Zone 2 speak ers: 1. Connect them directly to the A V receiver. 2. Connect them to an amp in Zone 2. Connectin[...]

112 Zone 2 and Zone 3 —Continued Zone 2 Video Outputs The A V receiver features a composite video output and component video output for connection to a TV in Zone 2, so you can enjoy both audio and video in that zone. Hookup • Use a composite video cable to connect the A V receiv er’ s ZONE 2 OUT V jack to a composite video input on your Zone[...]

113 Zone 2 and Zone 3 —Continued If you’ ve connected your Zone 2 speak ers to the A V receiv er, as explained in “Connecting Y our Zone 2 Speakers Directly to the A V receiv er” on page 111, you must set the Powered Zone 2 setting to Act (Activ ated). Notes: • When Act is selected and Zone 2 turned on, the Zone 2 speakers connected to th[...]

114 Zone 2 and Zone 3 —Continued If you’ ve connected your Zone 2 or Zone 3 speak ers to an amp with no volume control, set the Zone 2 Out or Zone 3 Out setting, respectiv ely , to V ariable so that you can set the zone’ s v olume, balance, and tone on the A V receiv er. Note: • This procedure can also be performed on the A V receiv er by u[...]

115 Zone 2 and Zone 3 —Continued Selecting an Input Source f or Zones Notes: •T o select AM or FM, press the [T uner] input selector b utton repeatedly . On the North American model, you can also select XM or SIRIUS. • Only analog input sources are output by Zone 2 and Zone 3. Digital input sources are not output. If no sound is heard when an[...]

116 Zone 2 and Zone 3 —Continued Adjusting the V olume of Zones Adjusting the Balance of Zones Muting Zones Adjusting the T one of Zone 2 Notes: • Zones can also be unmuted by adjusting the volume. • The tone cannot be adjusted for Zone 3. • The Zone 2 lev el, balance, and tone functions hav e no effect on the ZONE 2 PRE OUT when the Zone 2[...]

117 Zone 2 and Zone 3 —Continued The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when the y are selected as the input source. The triggers can be set so that they acti vate when a connected component is selected as the input source for the main room, Zone 2, Zone 3, or any combination of rooms. Whe[...]

118 Zone 2 and Zone 3 —Continued To control the A V receiver with the remote controller while you’ re in Zone 2 or Zone 3, you’ll need a commer - cially av ailable multiroom remote control kit for each zone. • Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the A V receiv[...]

119 Contr olling Other Components Y ou can control your other components, including those made by other manufacturers, with the remote controller . This section explains ho w to: • Enter the remote control code for a component that you want to control: D VD, TV , VCR, etc. • Learn commands directly from another component’ s remote controller [...]

120 Controlling Other Components —Continued Remote Control Codes f or Integra/Onky o Components Connected via Integra/Onk yo components that are connected via are controlled by pointing the remote controller at the A V receiv er, not the component. This allo ws you to control components that are out of view , in a rack, for example. If you want t[...]

121 Controlling Other Components —Continued To control another component, point the remote controller at it and use the buttons explained belo w . (Y ou must select the appropriate remote controller mode with the Remote Mode buttons first.) W ith some components, certain buttons may not work as expected, and some may not w ork at all. ■ Contro[...]

122 Controlling Other Components —Continued The A V receiver’ s remote controller can learn the com- mands of other remote controllers. By transmitting, for example, the Play command from your CD player’ s remote controller , the remote controller can learn it, and then transmit the exact same command when its Play [] button is pressed in the[...]

123 Controlling Other Components —Continued Y ou can program the remote controller’ s Macro buttons to perform a sequence of remote control actions. Example: To play a CD you typically need to perform the follow- ing actions: 1. Press the [Receiv er] Remote Mode button to select the Receiv er remote controller mode. 2. Press the [On] button to [...]

124 Tr oubleshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. If you can’t resolv e the issue yourself, contact the dealer from whom you purchased this unit. Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly . • Unplug the power cord from th[...]

125 Tr oubleshooting —Continued The subwoof er produces no sound • If the source material contains no audio in the LFE channel, the subwoofer produces no sound. • Check the Speaker Configuration (page 96). The Zone 2/3 speakers pr oduce no sound • The Zone 2/3 speakers only output sources that are connected to an analog input. Check to see[...]

126 Tr oubleshooting —Continued • Listen to the station in mono (page 61). • When listening to an AM station, operating the remote controller may cause noise. •P assing cars and airplanes can cause interference. • Concrete walls weaken radio signals. • If nothing improv es the reception, install an outdoor antenna. The remote controller[...]

127 Specifications Amplifier Section Video Section T uner Section ■ FM ■ AM ■ Digital T uner General ■ Video Input ■ Video Output ■ A udio Inputs ■ A udio Outputs ■ Control T erminal Specifications and features are subject to change without notice. Rated Output Power North American: 130 watts minimum continuous power per channel,[...]

SN 29344459A (C) Copyright 2007 ONKY O CORPORA TION Japan. All rights reserved. I0805-2 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neya[...]