Intel GENE-8310 инструкция обслуживания

SubCompact Board GENE-8310 GENE-8310 I n t e l ® Celeron ® M Processor Subcompact Board With LVDS, Ethernet, 6 Channel Audio & Mini PCI GENE-8310 Rev . A Manual 2nd Ed. Jan. 2006[...]

SubCompact Board GENE-8310 i Copyright Notice This document is copyrighted, 2006. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means wit[...]

SubCompact Board GENE-8310 i i Acknowledgments All other products’ name or tradem arks are properties of their respective owners.  Award is a trademark of Award Software International, Inc.  CompactFlash™ is a trademark of the Compact Flash Association.  Intel ® , Pentium ® M, and Celeron ® M are trademarks of Intel ® Corporation. [...]

SubCompact Board GENE-8310 iii Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 GENE-8310 CPU Card • 1 IDE Cable • 1 KB/Mouse Cable • 2 USB Cable • 1 Audio Cable • 1 COM Port Cable • 1 TV-out and S-terminal Cable • 1 DVI Cable • 1 Parallel Port Cable • 1 Jum[...]

SubCompact Board GENE-8310 i v Contents Chapter 1 General Information 1.1 Introduct ion ................................................................ 1-2 1.2 Featur es .................................................................... 1-4 1.3 Specific ations ............................................................ 1-5 Chapter 2 Quick Insta[...]

SubCompact Board GENE-8310 v 2.18 4P Power Conne ctor (CN9) .................................... 2-16 2.19 TV-out Connec tor (CN10) ....................................... 2-17 2.20 DVI Connecto r (CN11) ............................................ 2-17 2.21 Audio Input/Output Connector ( CN12) .................... 2-17 2.22 Ethernet 10/100 BaseT R[...]

SubCompact Board GENE-8310 v i Appendix B I/O Information B.1 I/O Addre ss Map .................................................... B-2 B.2 1 st MB Memory Address Map ................................B-2 B.3 IRQ Mappi ng Chart ................................................ B-3 B.4 DMA Channel As signments ...................................B-3[...]

SubCompact Board GENE-8310 C h a p t e r 1 G e n e r a l I n f o r m a t i o n 1- 1 General Chapter 1 Information[...]

SubCompact Board GENE-8310 Chapter 1 General Information 1-2 1.1 Introduction The GENE-8310 is the third generati on of fanless solutions that AAEON has released through their original design. It is more advanced than previous SubCompact Boards, with higher performance and lower power consumption. We believe the GENE-8310 will become one of the bes[...]

SubCompact Board GENE-8310 Chapter 1 General Information 1-3 Intel ® platform. It has the best graphics cap ability among current 3.5” SubCompact Boards. In addition, the GENE-8310 supports CRT , LCD, DVI and TV -out which can meet your requirements. The result is you will never need to wo rry about the limitations of board size and power consum[...]

SubCompact Board GENE-8310 Chapter 1 General Information 1-4 1.2 Features • Onboard Intel ® Celeron ® M or Mobile Intel ® Celeron ® Processor at 600MHz 0K L2 Cache Processor • 48-bit Dual Channels LVDS TFT LCD • 10/100Mbps Fast Ethernet • AC-97 3D Surround 5.1 Channel Audio • Supports Type II CompactFlash™ Memory • 2 COM / 4 USB2.[...]

SubCompact Board GENE-8310 Chapter 1 General Information 1-5 1.3 Specifications System • CPU: Onboard Mobile Intel ® Celeron ® Processor at 600MHz with 0K L2 Cache or Intel ® Celeron ® M Processor 1.3GHz  Memory: 200-pin DDR SODIMM x 1, Max. 1GB (DDR 266MHz)  Chipset: Intel ® 852GM + 82801 DB (ICH4)  I/O Chipset: ITE IT8712IX  Et[...]

SubCompact Board GENE-8310 Chapter 1 General Information 1-6 101.6mm)  Gross Weight: 0.88lb (0.4kg)  Operating Temperature: 32 ° F~140 ° F (0 ° C~60 ° C) Display  Chip: Intel ® 852GM + Chrontel 7009  Memory: Shared System Memory Up to 64MB with DVMT  Resolutions: Up to 1280 x 1024 @ 32bpp Colors for CRT; Up to 1280 x 1024 @ 24bp[...]

SubCompact Board GENE-8310 Chapter 1 General Information 1-7  USB: Two 5 x 2 Pin Headers Support 4 USB 2.0 Ports (Does not support Wake-up function)[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-1 Quick Inst allation Chapter 2 Guide Notice: The Quick Installatio n Guide is derive d f rom Chapter 2 of user manual. For othe r chapters and further ins tallation instructio ns, please refer to the use r manual CD-ROM that came with th e p roduct. Part No. 2[...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-2 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static ch[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-3 2.2 Location of Connectors and Jumpers Component Side 1 5 5 1 1 6 9 1 0 1 2 1 1 2 1 8 7 MPCI1 CN15 CN13 CN10 CN17 CN18 CN11 CN8 CN16 CN19 CN9 C N 1 C N 6 C N 3 C N 2 C N 4 C N 5 C N 1 4 C N 7 J P 5 C N 1 2 J P 2 JP1 The Height of Cooling System Depends on Cus[...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-4 Solder Side CFD1 DIMM1[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-5 2.3 Mechanical Draw ing Component Side 1 5 5 1 1 6 9 1 0 1 2 1 1 2 1 8 7 0.00 0 . 0 0 8.89 1 . 3 2 8.89 3 . 2 3 0.27 6.99 5 . 0 3 5 . 4 7 1 6 . 9 0 2 8 . 3 3 3 9 . 7 6 5 1 . 1 9 5 0 . 7 5 7 8 . 0 5 0.00 9 5 . 2 0 23.50 9 5 . 8 3 41.59 6 3 . 4 5 8 4 . 7 7 50.3[...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-6 Solder Side 0.00 0 . 0 0 3 . 2 3 8.89 0.00 9 5 . 2 0 9 8 . 3 7 8.89 72.39 114.30 133.93 0 . 0 0 133.93 9 5 . 2 0 109.22 0 . 5 8 0 . 5 8 8 7 . 5 8[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-7 2.4 List of Jumpers The board has a number of jumpers t hat allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: Jumpers Label Function J P1 C l ea r C M OS JP2 LCD V olta g e Sel[...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-8 2.5 List of Connectors The board has a number of connectors t hat allow you to configure your system to suit your application. T he table below shows the function of each board's connectors: Connectors Label Function CN1 USB 2.0 Port 1 Connector CN2 USB 2.0 Port 2 Connector CN3[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-9 CN17 Mini-DIN PS/2 Connector CN18 Serial Port COM 1 Connector CN19 CRT Display Connector VBA T2 External Battery MPCI1 Mini PCI Slot CFD1 Compact Flash Disk Slot[...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-10 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the si mplest kind of electric sw itch. It consists of two metal pins and a sma ll metal clip (often protected by a plastic cover) that slides over the pins to connect[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-11 2.7 Clear CMOS Selection (JP1) JP1 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.8 LCD Voltage Selection (JP2) JP2 Function 1-2 +5V (Default) 2-3 +3.3V 2.9 COM2 RI/+5V Selection (JP5) JP5 Function 1-2 +5V 3-4 RI (Default) 2.10 USB2.0 Port 1 Connector (CN1) [...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-12 2.11 USB2.0 Port 2 Connector (CN2) Pin Signal P i n Signal 1 USBVDD2-3 2 USBGND 3 USBD2- 4 USBGND 5 USBD2+ 6 USBD3+ 7 USBGND 8 USBD3- 9 USBGND 10 USBVDD2-3 2.12 Primary IDE Hard Driv e Connector (CN3) Pin Signal P i n Signal 1 PRI_IDERST# 2 Ground 3 PDD7 4 PDD8 5 PDD6 6 PDD9 7 PDD5[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-13 29 PDDACK# 30 Ground 31 IRQ14 32 N/C 33 PDA1 34 P66DET 35 PDA0 36 PDA2 37 PDCS#1 38 PDCS#3 39 IDEACTP# 40 Ground 41 +5V olt. 42 +5V olt. 43 Ground 44 N/C 2.13 Digital IO Connector (CN4) Pin N a m e Pin N a m e 1 Port 1 2 Port 2 3 Port 3 4 Port 4 5 Port 5 6 P[...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-14 Port 7 CN4. pin 7 Bit 1 U35. pin 26 (GPIO21) Port 8 CN4. pin 8 Bit 0 U35. pin 27 (GPIO20) 2.14 Front Panel (CN5) Pin Signal 1-2 A TX Powe r -on Button 3-4 HDD Active LED 5-6 External S peaker 7-8 Power LED 9-10 System Reset Button 2.15 Serial Port COM2 Connector (CN6) COM2/ RS-232 [...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-15 9 Ground 10 N/C COM2/ RS-485 Mode Pin Signal P i n Signal 1 TXD- 2 N/C 3 TXD+ 4 N/C 5 N/C 6 N/C 7 N/C 8 N/C 9 Ground 10 N/C Note: COM mode, RS-232/422/485, selected by BIOS. 2.16 Parallel Port Connector (CN7) Pin Signal P i n Signal 1 STB X 2A F D # 3 PTD0 4[...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-16 2.17 Dual Channel LVDS Connector (CN8) Pin Signal Pin Signal 1 Back-Li g ht Enable 2 Back-Li g ht Control 3 LCD V olt. 4 Ground 5 TXLCLK# 6 TXLCLK 7 LCD V olt. 8 Ground 9 TXL0# 10 TXL0 1 1 TXL1# 12 TXL1 13 TXL2# 14 TXL2 15 TXL3# 16 TXL3 17 L VDS_DA T A 18 L VDS_CLK 19 TXU0# 20 TXU0[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-17 2.19 TV-Out Connector (CN10) Pin Signal Pin Signal 1 Y 2 CVBS 3 Ground 4 Ground 5 C 6 N/C 7 Ground 8 N/C 2.20 DVI Connector (CN11) Pin Signal Pin Signal 1 TD1 2 TD1# 3 Ground 4 Ground 5 TDC 6 TDC# 7 Ground 8 +5V 9 HPDET 10 +5V 1 1 TD2 12 TD2# 13 Ground 14 Gr[...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-18 9 Audio Ground 10 CD_R 1 1 LINE_OUT L 12 LINE_OUT R 13 Audio Ground 14 Audio Ground 2.22 Ethernet 10/100Base-TX RJ- 45 Phone Jack Connector (CN13) Pin Signal Pin Signal 1 TX+ 2 T X - 3 TCT 4 N/C 5 N/C 6 RCT 7 RX+ 8 RX- 9 LINK_LED 10 ACT_LED 1 1 SPD_LED 12 +3.3V 2.23 External 5VSB/P[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-19 3 Rx 4 Ground 5 Tx 6 N/C (CIR_Rx Option) 2.25 Fan Connector (CN16) Pin Signal 1 F AN Sense 2 +5V 3 Ground 2.26 Mini-DIN PS/2 Connector (CN17) Pin Signal Pin Signal 1 Ke y board Data 2 Mouse Data 3 Ground 4 Shield 5 +5V 6 Keyboard Clock 7 Shield 8 Mouse Clock[...]

SubCompact Board GENE-8310 Chapter 2 Quick Inst allation Guide 2-20 2.28 CRT Display Connector (CN19) Pin Signal Pin Signal 1 CRT RED 9 5V 2 CRT_GREEN 10 VGA Ground 3 CRT_BLUE 1 1 N/C 4 N/C 12 CRT_SDA 5 VGA Ground 13 CRT_HSYNC 6 VGA Ground 14 CRT_VSYNC 7 VGA Ground 15 CRT_SCL 8 VGA Ground 2.29 External Battery (VBAT2) Pin Signal 1 VBA T ( +3V ) 2 G[...]

SubCompact Board GENE-8310 C h a p t e r 2 Q u i c k I n s t a l l a t i o n G u i d e 2-21 7 SDCS#1 32 SDCS#3 8 Ground 33 Ground 9 Ground 34 SDIOR# 10 Ground 35 SDIOW# 1 1 Ground 36 +5 V olt. 12 Ground 37 IRQ15 13 +5V 38 +5V 14 Ground 39 CSEL# 15 Ground 40 N/C 16 Ground 41 IDERST# 17 Ground 42 SIORDY 18 SDA2 43 N/C 19 SDA1 44 +5V 20 SDA0 45 DASP# [...]

SubCompact Board GENE-8310 C h a p t e r 3 A w a r d B I O S S e t u p 3-1 Chapter Aw a r d 3 BIOS Setup[...]

SubCompact Board GENE-8310 Chapter 3 A ward BIOS Setup 3-2 3.1 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error duri ng the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of erro rs: fatal and non-f atal. The system can usua[...]

SubCompact Board GENE-8310 C h a p t e r 3 A w a r d B I O S S e t u p 3 - 3 3.2 Aw ard BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery -backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Set[...]

SubCompact Board GENE-8310 Chapter 3 A ward BIOS Setup 3-4 Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify y our settings for integrated peripherals. (Primary slave, secondary slave, keyboard, mouse etc.) Power Management Setup Use this menu to specify[...]

SubCompact Board GENE-8310 C h a p t e r 3 A w a r d B I O S S e t u p 3 - 5 While AWARD has desig nated the cu st om BI OS t o maximize performance, the factory has the right to change these defaults to meet their needs. Set Supervisor/User Password Use this menu to set Supervisor/User Passwords. Save and Exit Setup Save CMOS value changes to CMOS[...]

SubCompact Board GENE-8310 C h a p t e r 4 D r i v e r I n s t a l l a t i o n 4-1 Chapter Driver 4 Inst allation[...]

SubCompact Board GENE-8310 Chapter 4 Driver Installation 4-2 The GENE-8310 comes with a CD-ROM that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: Step 1 – Install Intel ® INF Update for Windows 2000/XP Step 2 – Install Intel ® Extreme Graphics 2 Driver Step 3 – Install Intel ® LA[...]

SubCompact Board GENE-8310 C h a p t e r 4 D r i v e r s I n s t a l l a t i o n 4-3 4.1 Installation: Insert the GENE-8310 CD-ROM in to the CD-ROM Driv e. And install the drivers from Step 1 to Step 4 in order. Step 1 – Install Intel ® INF Update for Windows 2000/XP 1. Click on the Intel ® INF Update for Windows 2000/XP folder and then double [...]

SubCompact Board GENE-8310 Chapter 4 Driver Installation 4-4 Step 4 – Install Realtek AC97 codec Driver 1. Click on the Realtek AC97 codec Driver folder and then double click on the setup.exe 2. Follow the instructions that the window shows 3. The system will help you inst all the driver automatically Note: Under the Window OS environment, if the[...]

SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-1 Programming the Appendix A W atchdog T imer[...]

SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-2 A.1 Programming GENE-8310 utilizes ITE 8712 chipset a s its watchdog timer controller. Below are the procedu res to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop cu stomized program to fit your applic[...]

SubCompact Board GENE-8310 Appendix A Programming the W atchdog Timer A-3 occur if the MB PnP Mode is not exited normally. (1) Enter the MB PnP Mode To enter the MB PnP Mode, four special I/O write operations are to be performed during Wait for Key state. To ensure the initial state of the key-check logi c, it is necessary to perform four write ope[...]

SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-4 WatchDog Timer Configuration Registe rs Configure Control (Index=02h) This register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them.[...]

SubCompact Board GENE-8310 Appendix A Programming the W atchdog Timer A-5 WatchDog Timer Control Register (Index=71h, Default=00h) WatchDog Timer Configuration Registe r (Index=72h, Default=00h) WatchDog Timer Time-out Value Re gister (Index=73h, Default=00h)[...]

SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-6 A.2 ITE8712 Watchdog Timer Initial Program .MODEL SMALL .CODE Main: CALL Enter_Configuration_mode CALL Check_Chip mov cl, 7 call Set_Logic_Device ;time setting mov cl, 10 ; 10 Sec dec al Watch_Dog_Setting: ;Timer setting mov al, cl mov cl, 73h call Superio_Set_Reg ;Clear b[...]

SubCompact Board GENE-8310 Appendix A Programming the W atchdog Timer A-7 ; game port enable mov cl, 9 call Set_Logic_Device Initial_OK: CALL Exit_Configuration_mode MOV AH,4Ch INT 21h Enter_Configuration_Mode PROC NEAR MOV SI,WORD PTR CS:[Offset Cfg_Port] MOV DX,02Eh MOV CX,04h Init_1: MOV AL,BYTE PTR CS:[SI] OUT DX,AL INC SI LOOP Init_1 RET Enter[...]

SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-8 RET Exit_Configuration_Mode ENDP Check_Chip PROC NEAR MOV AL,20h CALL Read_Configuration_Data CMP AL,87h JNE Not_Initial MOV AL,21h CALL Read_Configuration_Data CMP AL,12h JNE Not_Initial Need_Initial: STC RET Not_Initial: CLC RET Check_Chip ENDP Read_Configuration_Data PR[...]

SubCompact Board GENE-8310 Appendix A Programming the W atchdog Timer A-9 MOV DX,WORD PTR CS:[Cfg_Port+06h] IN AL,DX RET Read_Configuration_Data ENDP Write_Configuration_Data PROC NEAR MOV DX,WORD PTR CS:[Cfg_Port+04h] OUT DX,AL XCHG AL,AH MOV DX,WORD PTR CS:[Cfg_Port+06h] OUT DX,AL RET Write_Configuration_Data ENDP Superio_Set_Reg proc near push a[...]

SubCompact Board GENE-8310 Appendix A Programm ing the W atchdog T im er A-10 Set_Logic_Device proc near push ax push cx xchg al,cl mov cl,07h call Superio_Set_Reg pop cx pop ax ret Set_Logic_Device endp ;Select 02Eh->Index Port, 02Fh->Data Port Cfg_Port DB 087h,001h,055h,055h DW 02Eh,02Fh END Main Note: Interrupt level mapping 0Fh-Dh: not va[...]

SubCompact Board GENE-8310 A p p e n d i x B I / O I n f o r m a t i o n B-1 I/O Information Appendix B[...]

SubCompact Board GENE-8310 Appendix B I/O Information B-2 B.1 I/O Address Map Address Description User Address 000-01F DMA Controller #1 000-000F 020-03F Interrupt Controller #1, Master 020-021 040-05F System Time 040-043 060-06F 8042 (Keyboard Controller) 060-064 070-07F Real time Clock, NMI (non-maskabl e Interrupt) Mask 070-073 080-09F DMA Page [...]

SubCompact Board GENE-8310 A p p e n d i x B I / O I n f o r m a i o n B-3 B.3 IRQ Mapping Chart IRQ0 System Timer IRQ8 System CMOS / Real time clock IRQ1 Keyboard IRQ9 Microsoft ACPI – Compliant system IRQ2 Cascade to IRQ Controller IRQ10 Unused IRQ3 COM2 IRQ11 Unused IRQ4 COM1 IRQ12 PS/2 mouse IRQ5 Unused IRQ13 FPU IRQ6 Unused IRQ14 Primary IDE[...]