Jacuzzi F258000 инструкция обслуживания

WHIRLPOOL BA TH R INST ALLA TION AND OPERA TING MANUAL J-CORNER SHOWER T OWER ™ ENCLOSURE-V erona ™[...]

[...]

1 Important The bath must be installed according to installation instructions (F258000) for the Verona™ whirlpool bath. Follow the instructions to ensure that proper framing has been provided to support the J-Corner Shower Tower. Finishing materials must be waterproof and sealed so that spray and condensation do not cause moisture dam- age. NOTE:[...]

2 FIXED P ANEL SEE P AGE 13 & 14 BAILS SEE P AGE 6 F AC EPLA T E SEE P AGE 19 W ALLBAR SEE P AGE 7 MIXER (INCLUDING HOSE CONNECTIONS) SEE P AGES 8 & 1 1 L EXTRUSION SEE P AGE 18 L EXTRUSION SEE P AGE 18 TOP RING SEE P AGE 15 & 16 W ALL BRACKET SEE P AGE 15 & 16 TOWER SEE P AGE 10 HANDLE SEE P AGE 19 HAND HELD SHOWER, FLEX HOSE SEE P[...]

3 EXPLODED VIEW OF J-CORNER SHOWER TOWER END CAP SEE P AGE 18 BOTTOM RAIL SEE P AGE 13 & 14 SET SCREW SEE P AGE 14[...]

4 Shower T ower Hardware Identification Chart The diagrams for these fasteners are shown actual size for fast identification. HARDW ARE Z LOW TRACK END CAP CAP QTY . -1 EXTERNAL T O OTH LOCK-WA SHER #8 ST A INLESS STEEL W A SHER QTY .-1 Y SHEET MET A L SCREW #8-18X2" S.S. X SCREW QTY .-1 SCREW , HEX W ASHER BOL T 1/4-20X2.5" W BOL T QTY.-[...]

5 Shower T ower Hardware Identification Chart The diagrams for these fasteners are shown actual size for fast identification. HARDW ARE NUT QTY .-1 J W A SHER QTY .-1 I W A T ER INLET HARDW ARE LOCKNUT 1/2"-14NPT FIBRE W ASHER 1.24 DIA W ALL BAR HARDW ARE FLA T HEAD SCREW #10-24 x 2 1/2" ST A INLESS STEEL SCREW QTY .-2 E WAS H E R QTY .-2[...]

T OWER ASSEMBL Y 1. Assemble the four (4) bails to the tower wall. (See Illustration 1.) Do not overtighten the nuts on the threaded shaft end. Overtighten- ing may break the stud. BAIL ILLUSTRA TION 1 BAIL SET SCREW (8) BOL T (8) SHELF NUT (8) C A B EXTERNAL T O OTH LOCK-WA SHER #10 ST A INLESS STEEL W ASHER (8) D WAS H E R QTY .-8 D BOL T QTY .-8[...]

7 3. Attach the wallbar assembly to the tower wall. (See Illustration 3.) FLA T HEAD SCREW #10-24 x 2 1/2" ST A INLESS STEEL H G ILLUSTRA TION 3 1/8" BEAD OF CAULK W ALLBAR ST AND-OFF EXTERNAL T OOTH W ASHER F (2) SCREW E (2) CAP SIDE VIEW OF W ALLBAR W ALLBAR SHOWER HEAD BRACKET SOAPDISH SHOWER W ALL KEP NUT H (2) FLA T W ASHER G (2) EXT[...]

ILLUSTRA TION 5 A TT ACHING MIXER V AL VE TO SHOWER W ALL SCREW QTY .-3 N CROSS RECESS HEAD SCREW M4X12 ST AINLESS STEEL EXTERNAL TOOTH LOCK-WA SHER M4 ST AINLESS STEEL M W ASHER QTY.-3 ILLUSTRA TION 4 W A TER LINES T O MIXER V AL V E ✳ USE THREAD SEALANT SCREWS (3) W ASHER (3) N M K W A SHER QTY .-1 FIBER WA SHER .75 O.D. L ST ANDOFF QTY .-3 COL[...]

ILLUSTRA TION 8 O PIN QTY .-3 FLA T W ASHER #8 TYPE B ST A INLESS STEEL W A SHER QTY .-3 P P A N HEAD SCREW #8-32 x 1/2" ST A INLESS STEEL SCREW QTY .-3 Q SCREW Q W ASHER P PIN O TOWER BOTTOM ILLUSTRA TION 7 TOWER PINS PIN #8-32 .25DIA X 1" K W A SHER QTY .-1 ILLUSTRA TION 6 12" HOSE W A TER INLET TOWER W ALL FIBER W ASHER 90 ° ELBO[...]

10 T OWER INST ALLA TION 1. To locate the drilling template, place it over the bath. The template should be against the bath flange edge and template corner 'A' should be at the bath's corner. (See Illustration 9.) Note: If bath has been installed with finish materials over bath flange, trim an amount off the template along the bath [...]

11 5. Attach Hot and Cold water supply lines of the mixer to the stub-out supply lines. (See Illustration 10.) 6. Locate the on/off handle and temporarily place it on the mixer valve. (See Illustration 26 on page 19.) With the mixer valve in the OFF position, turn on the water supply. Check for leaks at all connectors. Seal any leaks and continue. [...]

12 PLACING TOWER ILLUST RATI ON 11 7. Dry fit tower pins into holes to check hole location. Apply sealant around the three tower wall holes on the bath and around the perimeter where the tower will sit. (See Illustration 11.) 8. Place the tower pins in the holes and push the tower down firmly. The tower will stand temporarily on its own. Clean off [...]

FIXED P ANEL BOTTOM RAIL LA Y A 1/4" BEAD OF SEALANT UNDER THE FIXED P ANEL TWO SCREWS 15 ° ILL U STRA T ION 14 ILL U STRA T ION 12 ILL U STRA T ION 13 S R 15 ° 1/8" IMPORT ANT : MUST DRILL A T A 15 ° ANGLE TO A VOID DRILLING THROUGH DOOR GUIDE AREA. IMPORT ANT : MUST DRILL A T A 15 ° ANGLE TO A VOID DRILLING THROUGH SIDE OF RAIL. M3.[...]

14 FIXED PANEL ASSEMBLE TO BATH 11. Screw 1 1/2" Allen set screw 3/4" deep into the bottom of the fixed panel. Lay a 1/4" bead of sealant under the bottom rail and inside the back channel of the vertical frame. Place the assembly against the vertical edge of the tower and onto the bath surface, interlocking the two extrusions. (See I[...]

ILL U STRA T ION 19 W AS HER (1) SCREWS (2) SCREW INTO FIXED P ANEL Y W X SCREW(1) SCREW HERE EXTERNAL T O OTH LOCK-WA SHER #8 STA INLESS STEEL W A SHER QTY .-1 Y BOL T QTY .-2 W SHEET MET A L SCREW #8-18X 2" S.S. SCREW QTY .-1 X RING TO T OWER SCREW , HEX W ASHER BOL T 1/4-20X2.5" ILL U STRA T ION 16 BRACKET LOCA TING P ARALLEL WITH STUD[...]

ILL U STRA T ION 20 IMPORT ANT : MUST DRILL A T A 15 ° ANGLE TO A VOID DRILLING THROUGH ROLLER TRACK OF TOP RING. ILL U STRA T I ON 22A BOL T QTY .-2 W M3.5X9.5MM ST AINLESS STEEL SCREW QTY .-1 S DRILLING TOP RING RING TO BRACKET ILL U STRA T I ON 22B RING TO BRACKET ILL U STRA T ION 21 DRILLING TOP RING SCREW , HEX W ASHER BOL T 1/4-20X2.5" [...]

17 16. Apply sealant in frame and extrusion. Align and place extrusion above end cap onto the fixed glass. FIXED GLASS FRAME END ATTACHMENT ILL U STRA T ION 23 SEALANT FIXED GLASS END EXTRUSION[...]

17. Install on the sides of the tower the aluminum extrusions provided. They may be sealed in place or secured with screws (S, quantity 6). Seal the end cap by applying clear silicone sealant prior to placing into the end of the lower track. Secure with self-tapping screw S. 18 END CAP L-EXTRUSION L-EXTRUSION SEALANT BACK W ALL W ALL ILLUSTRA TION [...]

ILL U STRA T ION 25 F ACEPLA TE TOWER W ALL FOAM GASKET SEALANT HAND HELD SHOWER W ASHER TOWER W ALL FLEX HOSE W ASHER TEFLON T APE W A TER CONNECTOR W ALL BAR ILL U STRA T ION 27 ILL U STRA T ION 26 HANDLE INST ALLA TION HOT COLD ILL U STRA T ION 28 PLUG FOAM GASKET 3"O.D. (N OT SHOWN SEE P AGE 5) FOAM GASKET OFF SCREW W ASHER CAP CC BB SCREW[...]

[...]

[...]

Printed in the U.S.A. PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific loca[...]