Jacuzzi J-SHA инструкция обслуживания

Whirlpool Bath J-SHA ™ II Installation / Operating Instructions[...]

IMPORT ANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SA VE THESE INSTRUCTIONS WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE HYDROMASSAGE BATHTUB WITHOUT ADULT SUPERVISION. WARNING : TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE BATHTUB WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING;[...]

16 Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electri- cal installation according to codes are required for proper installation and user satisfaction. We recom- mend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our war- ranty does not cover improper[...]

Specifications _______________________________________________________________________ 1 Framing and Support _________________________________________________________________ 2 Rough-in Reference __________________________________________________________________ 2 Electrical and Service Access _______________________________________________________[...]

J-Sha II Owner's Manual PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 1 Specifications 36" (914 mm) 71-3/4" (1822 mm) 21-1/4" (540 mm) 2 (51 mm) 18" (456 mm) 9-7/16" (240 mm) 5-3/8" TOP VIEW SIDE VIEW (137 mm) DIMENSIONS 71-3/4" (1822 mm) L 36" ( 914 mm) W 21-1/4" ( 546 mm) H BATH ELE[...]

J-Sha II Owner's Manual Framing and Support The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. If the subfloor is level, no other preparation is necessary. You can proceed to install the bath. If the subfloor is not level, you MUST level the entire surface prior to installing the bath. Use a[...]

J-Sha II Owner's Manual Electrical Connections Two separate circuits are required for this unit: 1. Whirlpool bath controller. 2. Rapid Heat. 1. J-Sha II Install a 120 VAC 20 AMP dedicated circuit protected by a Ground Fault Circuit Interrupter (GFCI). DANGER: RISK OF ELECTRIC SHOCK. Connect only to a circuit protected by a Ground Fault Circui[...]

J-Sha II Owner's Manual 4 Drain Information A drain/overflow assembly must be installed on the bath, water tested, and connected to the sanitary system of the house. After opening the carton, inspect for damage. A solvent weld type drain is included and must be installed as shown. The drain solenoid wiring plug must be connected to the control[...]

J-Sha II Owner's Manual 5 W ater Supply Consult local authorities for plumbing code requirements in your area. IMPORTANT: Proper installation of the fill spout plumbing and compliance with local codes are the responsibility of the installer. Jacuzzi Whirlpool Bath does not warrant connections of water supply fittings and piping, fill systems, [...]

J-Sha II Owner's Manual 6 WA TER LEVEL SENSOR The bath is equipped with a water level sensor. When the water level is below the sensor, the pump/motor can not be activated. When the water goes above the level sensor, the pump/motor can then be activated. If the water level drops below the level sensor, the pump/motor will shut off . To restart[...]

J-Sha II Owner's Manual 7 80-1 30 1 30-220 11 0 - 15 0 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ TO NI C RELAX + + + _ _ _ MIX ON OFF Control Panel ON OFF MIX ON/OFF Button: T urns system on or off. BODY JET Button: T urns the body jets on or off. BACK JET Button: Selects the massage cycle. MIX Button: Selects both body jets and back jets. AIR Bu[...]

J-Sha II Owner's Manual Control Panel Functions 80-1 30 1 30-220 11 0 - 15 0 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ T ONIC RELAX T ONIC/RELAX Button: Select either the T onic or Relax cycle. The LED will light to indicate which cycle is selected. BODY WEIGHT Button: Selects a body weight range. The LED will light to indicate which weight range[...]

J-Sha II Owner's Manual 80-1 30 1 30-220 11 0-1 50 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ TONIC RELAX + + + _ _ _ MIX ON OFF ON/OFF BUTTON & LED BACK JETS BUTTON & LED TONIC/RELAX BUTT ON & LED BODY WEIGHT BUTTON & LEDs TIME BUTTON & LED SCALE SPEED BUTTON & LED SCALE INTENSITY BUTT ON & LED SCALE ST ART UP Press ON[...]

J-Sha II Owner's Manual 80-1 30 1 30-220 11 0-1 50 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ T ONIC RELAX + + + _ _ _ MIX ON OFF ON/OFF BUTTON & LED BODY JETS BUTT ON & LED TIME BUTTON & LED SCALE INTENSITY BUTT ON & LED SCALE AIR INCREASE & DECREASE BUTTONS & LED SQUARE W A VE BUTTON & LED MAXIMUM PEAK BUTTONS & L[...]

J-Sha II Owner's Manual 80-1 30 1 30-220 11 0-1 50 TIME SPEED INTENSIT Y + + _ + _ 02 5 _ TONIC RELAX + + + _ _ _ MIX ON OFF ON/OFF BUTTON & LED TIME BUTTON & LED SCALE SPEED BUTTON & LED SCALE INTENSITY BUTT ON & LED SCALE MIX BUTTON AIR INCREASE & DECREASE BUTTONS & LED MIX Both back jets and body jets operate in this[...]

Maintenance Back Jet Manifold Drainage When the unit is turned off, the back jet manifold will continue to drain after the bath is empty Cleaning the J-Sha To clean your J-Sha whirlpool bath, simply use a mild nonabrasive liquid detergent or commercially prepared bathtub cleaner. Do not use abrasive cleaners. You can protect and restore the gloss t[...]

13 LIGHT BULB LIGHT BEZEL SHELL BULB RECEPT ACLE LOCKING NUT LIGHT BULB REPLACEMENT Repairs to the Surface Minor scratches which do not penetrate the color finish (acrylic) can be removed with 600-grit wet/dry sandpaper. Restore the glossy finish with an acrylic polish or a comparable automotive paste wax. Major scratches or gouges which penetrate [...]

14[...]

WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its [...]

RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In [...]