JAI CV-A11 инструкция обслуживания

Progressive Scan Monochrome CCD Camera CV -A11 Operation Manual Camera: Revision B Manual: Version 2.1 A11Manualjul15 JPT 15-07-03[...]

CV-A11 DECLARA TION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EE C EMC (ELECTROMAGNETIC COMPAB ILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLOWING PROV ISIONS APPLYING TO IT. EN-50081-1 EN-50082-1 Table of Contents 1. General..........................................................................................[...]

CV-A11 1. Gener al The CV-A11 is a monochrome progressive scan 1/3” CCD cameras, designed for automated inspection application, featuring an extremely small housing and a wide range of unique functions. The asynchronous trigger can be set to work in several modes, to all ow functions such as pulse width controlled shutter, programmable shutter sp[...]

CV-A11 4. Camer a Housing and Dimensions Fig. 1. Locations and dimensions. 1. 12 pin Hirose connector for frame grabber interfacing and power (12V DC). 2. BNC connector for video output. VS 1.0 Vpp 75 Ohm. 3. 6 pin Hirose connector for trigger input and RS-232C control interface. 4. Gain potentiometer for manual gain setting. 5. Mounting holes, 8 x[...]

CV-A11 5. Pin Assignment 5.1. 12-pin Multi-connector (DC- IN/VIDEO OUT, EXT.HD/VD IN) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Pin configuration is compatible with EIAJ standard Pin no. Signal Remarks 1 GND 2 +12 V DC input 3 GND 4 Video output Parallel with t he BNC connector. 5 GND 6 HD input /HD output *) SW2.1 on for 75 Ω . SW1.1[...]

CV-A11 5.3. Input and Output Circuits In the following schematic diagrams the input and outpu t circuits for video and timing signa ls are shown. For alternative connections refer t o “10.1. CV-A11 emulating CV-M10 interfacing.” Jumper settings are shown as for factory defaul t. 5.3.1. Video output GND #4/ 12 75 Video Out put NC 82p 2 µ 7 CXA1[...]

CV-A11 6. F unctions and Oper ations Apart from the standard continuous operation, t h e CV-A11 features three external asynchronous trigger modes (edge pre-select, pulse width cont rolled and start/stop) and a special frame-delay readout mode. Long integration ti me mode is also supp orted. In addition, the CV-A11 also provide s a partial scan rea[...]

CV-A11 6.2. Input-output of HD/VD Signals In the default setting the camera will accept external HD/VD signals on pin 6 and 7 of the 12 pin Hirose connector. If external HD/VD is applied, th e camera will synchronize to it. If no external sync signals are applied, the camera will oper ate with its internal x-tal controlled sync. The camera scanning[...]

CV-A11 6.4. External Trigger Modes This camera has 6 external asynchr onous trigger modes, which can be s et by RS-232C commands. 1. Edge Pre-select Mode.TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure. (HC=0, H C=1) 3. Frame Delay read out mode. TR=3 PWC exposure read out by ext. VD. (HC=0[...]

CV-A11 6.5. Edge Pre-select Mode An external trigger pulse initiates the capture (inp ut on pin 11 of the 12-pin Hirose connector or pin 5 of the 6-pin Hirose). The leading edge of the trigger pulse initiates the exposure (this is a falling edge if factory default). If the polarity of this pulse is reversed, the camera can be configured to correct [...]

CV-A11 6.6. Pulse Width Control Mode The leading edge of the trigger pulse initiates the capture. The exposure time (acc umulation time) is governed by the duration of the trigger pulse. If the polarity of this pulse is reversed, the camera can be configured to correct for it. The exposure time range is 1.5H to 1000H (shortest and longest pulse d u[...]

CV-A11 6.7. Frame-delay read out Mode This mode allows simultaneous c apture of multiple camera using a common external trigger pulse subsequent multiplexed (sequential) readou t using a single input frame grab ber, as the user has control over when the image is read ou t from the CCD sensor. The exposure starts at the falling edge of the ext. trig[...]

CV-A11 6.8. Long Time Exposure Mode The exposure time is the interval between 2 ext. VD pulses sent to the VD input of the camera (Pin No. 7 of the 12-pin Hirose connector). The ex posure starts after input of the first ext. VD pulse, and ends after the next input of the ne xt ext. VD pulse, which ag ain starts a new exposure. The long time exposur[...]

CV-A11 6.9. Start/Stop Mode The exposure time is controlled by the interval between the ext. trigger and the ext. VD signal. The exposure starts at the first HD pulse after t he falling edge of the ext. trigger, and stops at the rising edge of the VD pulse. The range can be between 1/30 to 1/10,000 secon d. The Start/Stop mode is a continuous mode [...]

CV-A11 6.10. Smearless Mode This mode will reduce the unwant ed smear signal from a highlighted scene when a short exposure time is used. The trigger mode is like edge pre-se lect, but a fast dump readout is performed before the active accumulation is started. It will remove the smear over the highlighted parts in the image, but there is still smea[...]

CV-A11 6.11. Partial scan readout mode This mode allows increased frame rate, as only a selected number of lines are re ad out. The vertical resolution is reduced as ou tlined below. Partial scan will operate in normal continuous mode and all trigger modes. Fig. 23. Partial scanning. The partial scanning settings are as follows: Readout format Fram[...]

CV-A11 6.12. Other Functions Gain and analogue settings. !! Do not adjust these s ettings unless you have knowl edge to video adjustments !! AS, AGC Switch The video gain can be set to AGC or manual . In AGC mode the video level is kept constant by the automatic gain control circuit within a 12 dB range. Normal 700 mVpp ± 30 mV. The level can be a[...]

CV-A11 7. Configuring the Camer a 7.1. RS-232C control. All configuration of the CV-A11 camera is done via the RS-232C port. The camera can be set up from a PC running terminal emulator softwa re, or using JAI´s camera control software. Below is the description of the ASCII based short command p rotocol. Communication setting. Baud Rate 9600 bps D[...]

CV-A11 7.2. CV-A11 RS-232C command list. Command Name Format Parameter Remarks A – General settings and useful commands EB Echo Back EB= [ Param. ] <CR><LF> 0=Echo off 1=Echo on Off at power up ST Camera Status request ST?<CR><LF> Actual setting HP Online Help reques t HP?<CR><LF> Command list VN F irmware vers[...]

CV-A11 7.3. Camera Control Tool for CV-A11 From www.jai.com CV-A11 Camera Control Tool for Wi ndows 98/NT/20 00 can be downloaded. The control tool contents a camera control program and tools for m aking your own program. Below the different windows are sh own. Control bar Windows for all functions Fig. 25. Windows from Camera Tools. For the integr[...]

CV-A11 7.4. Internal Switch and Jumper Settings. 7.4.1. HD/VD input-output selection In the default setting the camera will accept external HD/VD signals on pins 6 and 7 of the 12 pin Hirose connector. The compos ite video signal from the camera will be synchr onized to an external HD/VD source connected to the camera. TTL level (between 2 and 5 V)[...]

CV-A11 8. Specifications Specifications CV-A11 Scanning System Progressive 525 lines 30 frames/sec Frame rate (Full frame) 29.96 Hz Line frequency 15.734 kHz CCD sensor Monochrome 1/3” IT CCD. Sony ICX424AL, (ICX084AL-6, old) Sensing area 4.9 (h) x 3.7 (v) mm Effective pixels 659 (h) x 494 (v) Pixels in video output 648 (h) x 492 (v) Cell size 7.[...]

CV-A11 10. Appendix 10.1. CV-A11 emulating CV-M10 interfacing The CV-A11 has a slightly different pin configu r ation on the 12-pin Hirose connector, compared to the M-series. This new configura tion is compliant to the EIA-J standa rd. This means, however, that the CV-A11 is not completely backward co mpatible with the CV-M10, CV-M40, etc in all c[...]

CV-A11 10.2. Precautions Personnel not trained in dealing with similar elec tronic devices should not service this camera. The camera contains components sensitive to el ectrostatic discharge. The handling of these devices should follow the requirements of electrostatic se nsitive components. Do not attempt to disassemble this camera. Do not expose[...]

CV-A11 11. Users Record Camera type: CV-A11 Revision: (Revision A) Serial No. …………….. For camera revision hi story, please contact your local JAI d istributor. Users Mode Settings: Users Modifications: Company and product names mentioned in this manual are trademarks or registered trademarks of their respective owners. JAI A-S cannot be h[...]