JVC HR-S8010UM инструкция обслуживания

P age 1 May 2, 2003 10:12 am — 1 — ENGLISH VIDEO CASSETTE RECORDE R HR-S8010UM INSTR UCTIONS LPT0756-001A Printed in China COPYRIGHT © 2003 VICT OR COMP ANY OF J AP AN, L TD . 0503-AH-PJ-BJ CONTENTS Buttons, Connectors and Indicato rs .............. ............. .............. ....... 3 Basic Connections ................ ............. .......[...]

P age 2 May 2, 2003 10:12 am — 2 — ● Cassettes marked “S-VHS” and “V HS” can be used with this video cassette recorder. Howev er, S-VHS recordings are possible only with cassettes marked “S-VHS”. By using S-VHS ET it is possible to record and play back with S-VHS picture quality on VHS cassettes with this VCR. When the equipment i[...]

P age 3 May 2, 2003 10:12 am — 3 — Butt ons , Connect ors and Indicat ors Front Panel Rear Panel S-VIDEO VIDEO (MONO)L–AUDIO–R POWER REC P AUSE CH PLA Y STOP/EJECT Cassette loading slot VIDEO/AU DIO input connectors Display panel VCR mode indicator Play indicator Record indicator T imer mode indicator Channel and auxiliary input/Clock time [...]

P age 4 May 2, 2003 11:22 am — 4 — Remote On-screen display If you press OSD ( OK ) on the Remote when “SUPERIMPOSE” is set to “ON”( 墌 pg. 13), you can see the current VCR status on the TV screen. T o clear the time counter , press OSD ( OK ) again. T he indications are not recorded even if the VCR is in the recording mode. A Channel [...]

P age 5 May 2, 2003 10:12 am — 5 — Basic Connections A Check contents Make sure the pac kage contains all of the acc essories listed in “Specifications”( 墌 pg. 16). B Situate VCR Place the VCR on a stable, horizontal surface. C Connect VCR to TV RF Connection A Disconnect the TV antenna from the TV . B Connect the TV antenna cable to the [...]

P age 6 May 2, 2003 10:12 am — 6 — Initial Settings Plug&Play Setting A Perform Plug&Play setup Press 1 . ● T he Language Se lect screen appears. B Select language Press rt to mov e the highlight bar (arrow) to your desired language (ENGLISH or ESP AÑOL), then press OK or e . ● T he Cloc k Set screen appears. C Set time Press rt to[...]

P age 7 May 2, 2003 10:12 am — 7 — T uner Setting Setting channels automatically — Auto Channel Set P erform Auto Channel Set only if channels ha ve not been set correctly by the Plug&Pla y setting. A Access Main Menu screen, then T uner Set screen Press MENU on the Remo te. Press rt to move the highlight bar (arrow) to “TUNER SET”, t[...]

P age 8 May 2, 2003 10:12 am — 8 — Playback Basic Playback A Load a cassette Make sure the window side is up, th e re ar label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. ● Do not apply too much pressure w hen inserting. ● T he VCR turns on, and the counte r on the on-screen displa y is reset, [...]

P age 9 May 2, 2003 10:12 am — 9 — Automatic operatio ns after rewinding — Next Function Memory T he Next Function Memory “tells” the VCR what to do after rewinding is complete. Ensure that the VCR is in stop mode. ● For A utomatic Playbac k Start Press REW ( 3 ), then press PLA Y ( 4 ) within 2 seconds. ● For A utomatic P ow er Off P[...]

P age 10 May 2, 2003 10:12 am — 10 — Recor ding Accidental er asure pre vention T o prevent accidental recording on a recorded cassette, remove its record safety tab. T o record on it later, cover the hole with adhesive tape. Basic Recording A Load a cassette Make sure the record safety tab is intact. If not, cover the hole with adhesive tape b[...]

P age 11 May 2, 2003 10:12 am — 11 — Timer Recor ding Up to 8 timer recording programs can be made using Express timer programing method as far as a year in adv ance. Remember , the clock must be set before you can program the timer. NOTES: ● If all the 8 programs ha ve alread y been set, “PROGRAM FULL ” appears on the TV screen. ● Afte[...]

P age 12 May 2, 2003 10:12 am — 12 — Program overlap warning display If “PROGRAM NOT COMPLETED PROGRAM O VERLAP” appears, you ha ve another program ov erlapping the program you hav e just made. T he Progr a m Check sc reen appears and conflicting programs will start blinking. Example: Progr am 1 (you ha v e just made) and Progr am 4 overlap[...]

P age 13 May 2, 2003 10:12 am — 13 — Function settings Y ou can use the other useful functio n settings on the Function Set screen. A Access Main Menu screen, then Function Set screen Press MENU on the Remote. Press rt to move the highlight bar (arrow) to “FUNCTION SET”, then press OK or e . B Select Function Press rt to move the highlight [...]

P age 14 May 2, 2003 10:12 am — 14 — 䡵 BLUE BACK — ON /OFF When this function is set to “ON”, the TV screen becomes all blue when recei ving a channel not in use. NOTE: When you w ant to receive an unstable c hannel with poor signals, set this function to “OFF”. 䡵 2ND AUDIO RECORD — ON/ OFF ● When this function is set to “ON[...]

P age 15 May 2, 2003 10:12 am — 15 — Editing Y ou can use your VCR as the pla y back or recording VCR. Y ou can use a camcorder as the playbac k VCR and your VCR as the recording VCR. Refer also to the other components’ instruction manuals for connection and its operations. A Make connection s Example 1: Wh en another VCR is VHS VCR ● If an[...]

P age 16 May 2, 2003 10:12 am — 16 — Specifications Specifications shown are for SP mode unless specified other wise. E. & O.E. Design and specifications subject to c hange without notice. GENERAL P ower requirement : A C 110 V – 220 V d , 50 Hz/60 Hz P ower consumption P ower on : 16 W P ower off : 3.4 W Te m p e r a t u r e Operating : [...]