JVC TK-T8101WPRE инструкция обслуживания

   IR BULLET CAMERA TK-T8101WPRU IR BULLET CAMERA TK-T8101WPRE INSTRUCTIONS  [...]

Important Safety Information  Before attempting to connect or operate th is product, please read these instructions carefully and save this manual for future use. 1[...]

Important Safety Information  Warning and Operating Notes Installation and serving the camera should be perform ed only by qualified and expe rienced technicians to conform to all local codes and to maintain your warranty. WARNING! The use of CSA certified/UL Listed Class[...]

CONTENTS 1 Instructions ........................................................................................................................................... 4 1.1 Before You B egin .......................................................................................................................... 4 1.2 Dimensions ......................[...]

Introductions   1 ． Instructions The IR Bullet camera is ideal for indoor inst allation in commercial and residential environment. 1.1 Before You Begin Please read this guide carefully before you install the bullet camera. Keep this guide for future reference. 1.2 Dimensions 4[...]

  Par t Na m es an d L oc at i on s  1.3 Names of Camera Parts Figure 2-1 1. Camera main body 2. Sun shield:  Minimize the effects of rain and sunlight on image quality. 3. Externally adjustable focal length & focus 4. OSD menu joystick:  To use the OSD joystick control: • Press the OSD joystick control straight down to enter t[...]

  Par t Na m es an d L oc at i on s  1.4 Routine Maintenance y Use a soft, dry cloth to remove any fingerprints or dust. y Clean the camera housing with a soft, dry clot h. For more stubborn stains, use a cloth dampened with a small quantity of neutra l detergent, then wipe dry. Caution: Do not use volatile solvents such as alco hol, benze[...]

  Installa tion  2 Inst allation 2.1 Mounting the Camera Step 1: Drill mounting holes and insert anchors. In desired location, use the supplied Guide Pattern to drill three 5mm mounting holes. Then insert the supplied anchors into the holes. T o prevent the camera from falling off, ensures it is c onnected to a firm place (ceiling slab or [...]

  Installa tion  Step 2: Pass all the signal cabl es through the hole for the cables. Optionally connect a video monitor to the BNC connector if you want to perform focus/zoom adjustments during the installation.   Step 3: For static electricity protection, ensure that the rubber pad[...]

  Installa tion  Step 5: Adjustment It can be adjusted once the screw is fully loosened. After adjustment, be sure to lock it tightly for waterproof. Notice: Please be careful when adjusting T ele/Wide and N ear/Far so as to avoid damage to the lens Step 6: Place the three provided insu lation caps onto the three tapping screws. Insert the[...]

Menu Settings   3. OSD Settings Use the OSD menu to set up the camera for optimum performance      Figure 3-1 Main menu 3.1 Lens The LENS settings allow you to configure Lens and brightness. Options are AUTO (Auto Iris lens) and MANUAL. The default setting is AUTO. In the AUTO submenu, you can set the MODE as OPEN, CLOSE or AUT[...]

Menu Settings   If SHUTTER/AGC is set to MANUAL, the submenu is shown as below . The shutter speed is a variable from 1/50(1/60) sec to 1/10000sec and the AGC is select able depending on your environment condition. Recommended settings according to the application: 1. Auto Exposure by Iris Control: Application: General Pur pose, Indoor survei[...]

Menu Settings   If HLC is selected, HLC is ac tivated automatically when the camera detects high-luminance. 3.5 PICTURE ADJUST PICTURE ADJUST allows you to adjust picture settings for optim al image. In the PICT ADJUST submenu, you can adjust BRIGHTNESS, CONTRAST, SHARPNESS, HUE and GAIN value. In addition, you can set MIRROR to ON to reflect[...]

Menu Settings   3.9 DA Y/NIGHT The camera will automatically swit ch to B/W mode when the illuminati on is under a certain threshold. There is no need to adjust this setting. Under B/W mode, you can set BURST to be ON or OFF . 3.10 NR NR allows you to configure the DNR (Digital Noise Reduction) settings to reduce noise on the screen. In the N[...]

4. S pecification Si g nal S y stem NTSC P AL Image System Imager Size 1/3 type: IT CCD Effective pixels ?｢ Hx V ?｣ 976 (H) × 494 (V) 976 (H) × 582 (V) Optical system Lens F1.4, f:3.3 ~ 12mm A ngle of View Wide: 89.8°(H), 63.6°(V) T ele: 23.9°(H),17.9°(V) Electrical Specification TV System 2:1 Interlace Horizontal Resolution 600 TV lines [...]