Kawasaki 840116 инструкция обслуживания

8" BENCH DRILL PRESS INSTRUCTION MANUAL FOR CUSTOMER SERVICE POUR LE SERVICE APRÉS VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1-800-590-3723 Printed in China 87-1904-60957 KAW ASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP ., U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT . CONSUMER INQUIRES SHOUL[...]

SECTION FOUR MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26 SPECIFICA TIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 OTHER CONSUMER DO-IT -YOURSELF (DIY) TOOLS[...]

GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS RE AD AN D UND ER ST AND ALL INS TRUC TIO NS . Fa il ur e to fol lo w all ins tru ct io ns li st ed bel ow ma y re sult in ele ct ri c sh ock, fi re and /o r se rio us per so na l in jury . KEEP GUARDS IN PLACE AND IN WORKING ORDER. RE MO VE A DJ US TI NG KE YS A ND W RE NC HE S. For m a hab it [...]

This drill press is equipped with a grounded 3-wire power cord with a 3-prong plug. If the power cord will not fit into the wall plug, an approved adapter can be used as long as it is connected to the center screw in the wall plate. See Figure 1 and the steps below to use an AC grounding adapter: 1. Remove the cover plate mounting screw. 2. Insert [...]

USE ONL Y DRILL BITS, SANDING DRUMS, AND OTHER ACCESSORIES that are designed for the various speeds of this drill press. The drill bits, sanding drums and other accessories should have a shank size 1/2" OR SMALLER. Unsuitable drill bits can break without warning throwing fragments outward at high speeds possibly causing severe injuries. Contac[...]

SECURE THE ELECTRICAL POWER CORD when the drill press is not in use to prevent unauthorized use of the tool and/or to prevent children from acciden- tally turning it on. ADDITIONAL INFORMA TION about the proper use of bench-mounted drill presses is available from the Power T ool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www .powertoo[...]

FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS: 1. Drill Bit 2. Column Assembly 3. Feed Handles 4. Chuck Key 5. Drill Chuck 5. Head Assembly 6. Knob (and mtg Hardware) 7. Work T able ASSEMBL Y Do not begin assembly of Bench-mounted Drill Press if the AC power cord is plugged into an AC power receptacle. Do not begin assembly of Bench-mounted Drill [...]

Ensure the spindle taper (Q) and the tapered hole in the drill chuck (R) are clean and free of any grease, lacquer , or rust preventative coatings. These compounds can cause the drill chuck (R ) to seize when installed on the spindle shaft (Q). INST ALLING THE DRILL CHUCK 1. Open the jaws of the drill chuck (1) as wide as possible by turning the ch[...]

LASER GUIDE Use of controls or procedures, or performance of proce- dures other then those specified herein may result in hazardous radiation exposure. LASER SAFETY NEVER LOOK INTO THE LASER BEAM. Any contact with the eyes by the beam could cause injury . Do not use the laser when cutting reflective materials. DO NOT AIM THE LASER BEAM A T ANYONE O[...]

17 18 STORE OUT OF REACH OF CHILDREN. Equipment should be in a high location or locked up to keep out of reach of children. It is not a toy . DO NOT T AMPER WITH THE LASER OUTPUT . Changing the performance of the laser to increase its output is prohibited. Any claim for damages or injuries resulting from not following these instructions will be ref[...]

Ensure that the switch toggle, when removed, is kept in a secure place. Once removed, the drill press will not start without it. ADJUSTING THE WORK T ABLE 1. The worktable (1) can be raised or low- ered on the drill press column (2) by loosening the table clamp (3). See Figure 12. 2. After the table is positioned at the desire height, LOCK the tabl[...]

1. Lift up the pulley cover (1). 2. Release the belt tension by loosen- ing the tension lock knob (2) located on the side of the drill press head. Loosen the tension lock knob (2) by turning it counterclockwise. 3. Pivot the motor (3) towards the front of the drill press. 4. While holding the motor pivoted to the front of the drill press, position [...]

3. T urn the spring housing (5) counter- clockwise to increase the spring ten- sion or clockwise to decrease the spring tension. 4. T urn nut (4 - inside) until it contacts the spring housing (5). Back nut (4) out 1/4 turn and tighten it against nut (3 - outside) to hold the spring housing in place. 5. IMPORT ANT : The inside nut (4) should not tou[...]

Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. I f t h e d r il l p r es s mu s t b e us e d o u ts id e , u s e a n ex t en si o n c o rd l a be l e d “ W - A ” o r “W . ” T he se e x t e ns i o n c or d s a r e r a te d f o r o u t do o r u s e a n d r e du c e t h e ch an c es o f e l ec t ri ca l s h o ck[...]

Warranty Performance By pur chasing the product, purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and/or part is promptly returned to Alltrade’ s f[...]

ALL TRADE AND/OR ITS REPRESENT A TIVE(S), OR THE PURCHASER, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANT ABILITY AND THE W AR RA NTY OF FI TN ES S FOR A P AR TI CU LA R PUR POS E, AR E HER EB Y EXP RESS L Y EXCLUDED AND DISCLAIMED BY ALL TRADE AND/OR ITS REPRESENT A TIVES. PUR CH ASE R KNOW ING L Y AND WILL IN GL Y WAI VES ANY A ND[...]