Kenwood TK-8150 инструкция обслуживания

TK-7150 INSTRUCTION MANUAL VHF FM TRANSCEIVER © B62-1619-10 (K) 09 08 07 06 05 04 03 02 01 TK-8150 UHF FM TRANSCEIVER SCN SP OP OS AB MON CALL[...]

T HANK Y OU We are grateful you chose KENWOOD for your personal mobile applications. W e believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency . KENWOOD transceivers incorporate the latest in advanced technology . As a result, we feel strongly that you will be pleased with the qua[...]

i ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine or imprisonment or both. ◆ Refer service to qualified technicians only . Safety: It is important that the operator is aware of, and understands, hazards common to the operation [...]

ii CONTENTS UNP ACKING AND CHECKING EQUIPMENT ................................................ 1 S UPPLIED A CCESSORIES ................................................................................. 1 PREP ARA TION ............................................................................................... 2 T OOLS R EQUIRED .................[...]

1 UNP ACKING AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer , an authorized KENWOOD service facility , or the factory . Carefully unpack the transceiver . We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or ha[...]

2 V arious electronic equipment in your vehicle may malfunction if they are not properly protected from the radio frequency energy which is present while transmitting. Electronic fuel injection, anti-skid braking, and cruise control systems are typical examples of equipment that may malfunction. If your vehicle contains such equipment, consult the [...]

3 I NST ALLING THE T RANSCEIVER For passenger safety , install the transceiver securely , using the supplied mounting bracket, so the transceiver will not break loose in the event of a collision. 1 Mark the position of the holes in the dash by using the mounting bracket as a template. Drill the holes, then attach the mounting bracket using the supp[...]

4 ORIENT A TION F RONT P ANEL AND M ICROPHONE q q q q q V olume Control Rotate to adjust the volume level. Clockwise increases the volume and counterclockwise decreases the volume. w w w w w Display (See page 5.) e e e e e Selector Rotate to select a zone or channel/group ID. Clockwise increases the zone / channel/group ID and counterclockwise decr[...]

5 !0 !0 !0 !0 !0 PF5 Key Press this key to activate its programmable auxiliary function {page 7}. The default setting is None. !1 !1 !1 !1 !1 PF6 Key Press this key to activate its programmable auxiliary function {page 7}. The default setting is None. !2 !2 !2 !2 !2 TX / BUSY LEDs The TX LED lights red while transmitting. In Conventional Groups, th[...]

6 R EAR P ANEL 6-pin connector (for accessories) Power input connector Antenna connector 25-pin connector (for accessories)[...]

7 PROGRAMMABLE AUXILIARY FUNCTIONS Keys y to !1 {pages 4 and 5} can be programmed with the auxiliary functions listed below . The keys can only be programmed with functions, depending on whether you are using a Conventional Group or a T runking System. Please contact your dealer for further details on these functions. • Auto T elephone • AUX A [...]

8 BASIC OPERA TIONS O PERA TION O VERVIEW Y our dealer can program your transceiver with T runking Systems and Conventional Groups. T runking Systems can handle 32 zones with up to 250 group IDs. Conventional Groups can handle up to 128 zones with up to 128 channels. The transceiver can handle a maximum combination of 128 zones in T runking Systems[...]

9 TRUNKING ZONES P LACING A D ISP A TCH C ALL 1 Select the desired trunking zone and a group ID. 2 Press and hold the PTT switch. 3 If the “Clear to T alk” tone sounds, communication is possible; start speaking into the microphone. Release the PTT switch to receive. • For best sound quality at the receiving station, hold the microphone approx[...]

10 CONVENTIONAL ZONES T RANSMITTING 1 Select the desired conventional zone and a channel. • Make sure the channel is not in use. When a channel is in use, the BUSY (green) LED will light. 2 Press and hold the PTT switch, then speak into the microphone in your normal speaking voice. • For best sound quality at the receiving station, hold the mic[...]

11 SCAN To activate the Scan function, press the key programmed as Scan . • The SCN icon lights and “-SCAN-” appears on the display . To stop scanning, press the Scan key again. • The transceiver returns to the channel that was selected before Scan started. S CAN T YPES There are three types of scans available: Single Zone Scan, Multi Zone [...]

12 DTMF CALLS Note: To make DTMF calls, you must have an optional microphone with a DTMF keypad. M ANUAL D IALLING Press and hold the PTT switch, then enter the digits on the microphone keypad. •Y ou can enter the digits 0 ~ 9 , , and # . • If programmed by your dealer , you do not need to continuously hold the PTT switch; the transceiver will [...]

13 C LEARING S TORED DTMF N UMBERS 1 Press and hold the microphone # key for 1 second. • “D” appears on the display . 2 P ress the # key again. • “D–CLEAR” appears on the display . •T o cancel the process, press any key other than 0 ~ 9 . 3 Enter the desired memory location number (01 ~ 32). R EDIALLING 1 Press and hold the micropho[...]

14 FleetSync™: ALPHANUMERIC TWO-W A Y PAGING FUNCTION FleetSync™ is an Alphanumeric T wo-way Paging Function, and is a protocol owned by KENWOOD Corporation. FleetSync™ enables a variety of paging functions on your transceiver , some of which depend on dealer programming. Y our dealer can set up either FleetSync™ or FleetSync™ II on your [...]

15 O PTIONAL F EA TURES Short Messages: Received short messages (maximum of 48 characters) are displayed the same as Status messages {page 16}, however only 4 short messages can be stored in the stack memory . “M” (Message) and the message number appear with the message. GPS Report: If an external GPS receiver (NMEA-0183 format) is installed on[...]

16 ■ Identification Codes An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number . Each transceiver must have its own Fleet and ID number . • Enter a Fleet number (100 ~ 349) to make a group call. • Enter an ID number (1000 ~ 4999) to make an individual call in your fleet. • Enter a Fleet number followed by an ID numb[...]

17 ■ Receiving The mail icon ( ) will flash and a calling ID or text message will appear when a Status call is received. • The display alternates between the caller ID and the message. Press any key to return to Normal Operation Mode. ■ Reviewing Messages in the Stack Memory 1 Press and hold the key programmed as Message Mode for more than 1 [...]

18 ADV ANCED OPERA TIONS T IME - OUT T IMER (TOT) The T ime-out T imer prevents any single caller from using a channel for an extended period of time. If you continuously transmit for a period of time that exceeds the programmed time, the transceiver will stop transmitting and an alert tone will sound. T o stop the tone, release the PTT switch. Y o[...]

19 E MERGENCY O PERA TION Press and hold the key programmed as Emergency to enter Emergency Operation. • The duration you need to hold the key depends on how your transceiver has been set up. • The transceiver will switch to the pre-programmed emergency channel/ group ID. While in Emergency Operation, the transceiver will perform the emergency [...]