KitchenAid 9.76E+13 инструкция обслуживания

1 9 758644 9758644 Quic k Ref er ence Ta ble of Cont ents: P ages 2 3 3 4 5 - 8 9 Before you start P roduct dimensions Cabinet dimensions/requirements Electrical requirements Installation steps Chec k operation If range does not operate If you need assistance/service Moving the range Pa rt No. 9758644 30" Electric Freestanding Range W ARNING T[...]

2 Bef or e you star t... Mobile home installation The installation of this range must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, P art 3280 [formerly the F ederal Standard for Mobile Home Construction and Safety , Title 24, HUD (Par t 280)] or , when suc h standard is not applicable, the Standard for Manufact[...]

30" (7 6.2 cm) min. cabinet opening width F or minimum clearance to the top of the cooktop, see NOTE .* 18 " (45.7 cm) upper side cabinet to countertop 13" (33 cm) max. upper cabinet depth 4" (1 0.2 cm) min. clearance from both sides of range to side wall or other combustible material above the counter top. 7/8" (2.2 cm) mi[...]

4 Electr ical r equir ements  The range can be connected directly to the fused disconnect (or circuit breaker box) through flexible armored conduit. This range can be direct wired to a four - wire or three-wire aluminum wiring system. See “Direct wire method: Copper or Aluminum wire” section. Allow two to three feet of slac k in the line so [...]

5 No w star t... 1. R emo ve shipping materials, tape and protective film from range. Keep cardboard bottom and shipping base under range. Remo ve oven rac ks and parts pac kage from inside oven. 2. Ta ke four cardboard corners from the carton. Stac k one cardboard corner on top of another . R epeat with other two corners. Place them lengthwise on [...]

6 P ow er supply cord method: 1. Disconnect power . 2. Remo ve the knoc kout for the 40 amp power supply cord. 3. Assemble a U.L.-listed strain relief in the opening. 4. Insert the power supply cord through the strain relief, allowing enough slac k to easily at tac h the wiring to the terminal bloc k. W ARNING - Improper connection of the equipment[...]

7 Dir ect wir e method: Copper or Aluminum wir e Use this method only if local codes permit connecting ground conductor to neutral supply wire. 10 .L oosen (do not remove) the 3 slot ted set screws. Insert the neutral (white) wire into the hole at the bottom of the center position lug (attac hed to center terminal screw of terminal bloc k). S ee Fi[...]

8 9. Move range close to cabinet opening. 10 . R emove cardboard or hardboard from under range. Carefully move range into final position. 11. P ull drawer open to first stop position. Lift front of drawer to clear white wheels in drawer guides. Remo ve drawer and set it aside on a protected surface. Oper ating position 13 . If installing the range [...]

9 Chec k oper ation 17 . Chec k the operation of the cooktop elements: P ush in and turn eac h surface unit control knob to “HI” position. Chec k the operation of the cooktop elements and indicator lights. 18 . Chec k the operation of the o ven: P ress the “CL OCK SET” button. “TIME, HR AND MIN” will light up in the display . “0:0 0?[...]

10 If r ang e does not oper at e:  Chec k that the circuit breaker is not tripped or the house fuse blown.  Chec k that the power supply cord is plugged into the outlet.  S ee Use and Care Guide for troubleshooting list. If y ou need assistance: If you have questions about operating, cleaning or maintaining your range:  R efer to Use an[...]

11 Notes[...]

12 Pa rt No. 9758644 © 20 04 Kitc henAid P rinted in U .S.A. ® Registered T rademark of Kitc henAid. Prepared by Kitc henAid, Benton Harbor , Mic higan 49022 0 1/2004 HOME APPLIANCES[...]