KitchenAid KHMS 9010/I инструкция обслуживания

KHMS 9010/I[...]

[...]

Product description and symbols 4 Gas burner functions 4 Practical advice on how to use the burners 5 Injectors table 5 Induction zone functions 6 Positioning the pan supports and Wok support 7 Sizes and installation measurements (mm) 8 Precautions and general recommendations 9 Safeguarding the environment 10 Installation 11 Gas connection 12 Elect[...]

1. Removable pan supports 2. Professional double crown W ok burners 3. 145 mm diameter induction zone 4. Left gas burner control knob 5. Central gas burner control knob 6. Right gas burner control knob 7. Display and touch control panel for the induction zones Gas burner control knob symbols A. Burner position indicator B. Flame regulation symbols [...]

Read these instructions to get the best out of your burners: - Use pans with a diameter the same as the burner (see pan diameter table to the side). - Only use flat bottom pots and pans. - Use the right amount of water for cooking food and use the lid. Important: using the pan supports incorrectly will scratch the hob top: avoid placing them upside[...]

This hob is fitted with 2 induction zones that allow you to boil water very quickly , as well as control the temperature with extreme precision, giving you a vast range of cooking options. The induction zone control panel has the following functions. 1. On/off touch pad control 2. Child safety lock 3. Zone selection/ power level adjustment 4. Timer[...]

The time remaining can also be changed by pressing the clock symbol button (4) at any time and using the +/- buttons (3) to alter the time. The light above the display will flash for 10 seconds, then the display will show the amended time remaining. When the programmed time expires a continuous double signal will be heard. If a zone has been progra[...]

NOTE: If a hood is installed above the hob, read the instructions for fitting the hood where it indicates the correct distances to be complied with. • The cooktop has to be set into a work top between 20 - 40 mm deep. • The distance between the lower face of the glass ceramic hob and the cupboard or separating panel must comply with the sizes s[...]

T o get the best out of your hob, please read the instructions carefully and keep them for future consultation. • These instructions are only valid in the countries whose symbol of destination is shown on the product description sheet and hob. • The packaging (plastic bags, expanding polyurethane, etc.) poses a potential source of danger to chi[...]

P acking The packaging material is 100% recyclable and is labelled with the recycling symbol that identifies it as a kind of material to be sent to local waste disposal centres. Product This appliance is marked according to the European Directive 2002/96/EC, W aste Electrical and Electronic Equipment (WEEE). By ensuring that this product is dispose[...]

T echnical information for the installer • This product can be built into a 20 to 40 mm deep worktop. • The hob cannot be installed with an oven underneath. Always insert a separator panel under the hob at a distance of no less than 25 mm from the lowest point (electronic control module) on the appliance. Follow the measures shown in the “Siz[...]

The gas mains system must comply with local regulations. • The paragraph on “national legislation reference” shows the local legislation specific to the country of destination. • Should there be no information regarding your country of interest, ask for further details from the installer . • The connection of the hob to the gas mains netw[...]

1. After cleaning the surfaces around the edges, fit the seal provided around the hob. 2. P osition the hob inside the opening according to the sizes indicated in the description sheet. 3. Use the brackets (A) provided to secure the hob, fixing it with the proper screws to adapt it to the thickness. W arning: the electrical power cable must be long[...]

(See the product description sheet for model) Remove the bottom of the hob, lifting out the installation brackets to change the dual crown wok burner injector . Please contact the Customer Care Centre. REMOVING THE MAIN INJECTOR Remove the injector (F) using a 10mm spanner . Slacken the holding screw (H) to regulate the position (X) of the gas inle[...]

In order to keep your hob in good condition, you must keep it clean, removing any food residue each time you use it. Always disconnect the hob from the electrical power supply and wait until it cools before cleaning. Cleaning the surface of the hob: Stainless steel surfaces • The stainless steel surface may become stained if it comes into contact[...]

The hob is not working properly or not working at all. Before calling the Customer Care Centre, see if the problem you are encountering is mentioned in this guide. Contact the Customer Care Centre to replace the power cable. Burners and gas rings 1. The burner doesn’t come on or the flame is uneven. Check that: • the gas or electricity supply i[...]

Before contacting the Customer Care Centre, clarify that you cannot resolve the problem yourself based on the descriptions given in the “T roubleshooting guide”. 1. T urn the apparatus off and restart it to see if the fault is repeated. If after carrying out the above checks, the fault persists, contact your Customer Care Centre. Please give: ?[...]

[...]

[...]

5019 719 01020 Printed in Italy n 01/07 GB[...]