Kyocera FS FS-1920 инструкция обслуживания

FS-1920 P age Printer Operation Guide[...]

i Caution on Installation No liability is assumed for any damage caused by improp er installation. Notice on Software Software used with th is printer must sup p ort the printer’s emulation mode. The print er is factory-set to emulate th e PCL. The e mula- tion mode can be changed by follo wi ng the pr ocedures d escribed in Chapter 1 . Notice on[...]

ii IBM PROGRAM LICENSE AGREEMENT The device you have purchase d contains on e or more softwar e programs ("Programs") wh ich belong to intern ational business machin es corporation ("IBM"). Th is document defines the terms and conditions under which the soft ware is being licensed to you by IBM. I f you do not agree with the ter[...]

iii Typef ace T rademar k Acknowledgement All resident fonts in this printer are licensed from Agfa Corporation. Helvetica, P alatino and Times are regist e red trademarks of Linot ype-Hell AG . ITC Av ant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC Za pf Dingbats are registered trademarks of International Type- face Corporation. Agfa Japan[...]

Contents iv Contents Introduction .............. ................. ............. .......................................... .......... i x F eatures .. ................. ............ ................. ................ ............. ................ ................ .......................... ............. ....... x F or More Information... ........[...]

Contents v P agination ... ................ ............. ................ ............. ................ ................ ............. ........... ............... ............... 1-41 Emulation ... ................ ............. ................ ............. ................ ................. ............ ............ .............. ......... 1-[...]

Contents vi Configuration ........... ................ ............. ................ ................ ............. ................ ............. .......... ................ .. 1-91 P age P rotect Mode ........ ................. ............. ................ ................ ................ ............. ........... ................. 1-91 Linef[...]

Contents vii Chapter 4 T r oubleshooting ................ ................ ............................ .......... 4-1 General Guide ...................... ............. ................. ............ ................. ................ ............. .... .................. ........... 4-2 Print Quality Problems ........................ ............[...]

Contents viii Serial Interface (Option) ..... ................. ................ ................ ................ ............. ................ ... .................... ... B -6 RS-232C Interface ...... ................ ................. ............ ................. ................ ................ .......... ......... .......... B - 6 RS-232C[...]

ix Intr oduction The Ky ocera Mita page printer has many extrem ely desirable features. It was designed to make a contribution to a cleaner environment as well as to represent the latest generation of page printer technology . This section contains the following subsections. •F e a t u r e s • F or More Information ... • Guide to the Operatio[...]

x F eatures This section outlines the common major printer features of the FS-1920 page printer . Ultra long life modules The drum, d eveloper , an d fuser have been desig ned for ultra long life. Amor phous silicon dr um The drum has been developed usin g K yocera’s unique ceramic technology using amorphous silicon. KIR (Ky ocera Ima ge Refineme[...]

xi USB (Univ ersal Serial Bus) Interface This printer supports Full-S peed US B 2.0 standards. Connection to a computer with a USB interface gives a higher communication speed than parallel interface connection. e-MPS ‘e-MPS’ is an abbreviatio n for ‘en hanced-Mul tiple Printing Sys tem,’ which is a post-processing function that combines el[...]

xii Microdrive (hard disk unit) slot for various functions such as job retention, VMB , and mor e By saving print jobs onto the Microdrive, they can be printed out at the operator panel when desired. T he electr onic sort function can be used f or much faster printing . CompactFlash car d slot for option fonts, macros, for ms, etc. Data in the Comp[...]

xiii F or Mor e Infor ma tion... • For information on how to inst all the print er driver sof tware, refer to the KX Printer Driver Inst allation Guide that is included with the printer . • For information on ho w to use the printe r driver sof tware, refer to t he KX Printer Driver Operation Guid e that is included on the CD-ROM (comes wit h t[...]

xiv Guide to the Oper a tion Guide This Operation Guide has the following chapters: Chapter 1 Using the Operator Panel This chapter explains the message displa y , indicators and keys on the operator panel , and how to make variou s settings from the op erator panel. Chapter 2 Paper Selection This chapter explain s the types of p ape r that can be [...]

xv Indicates tips or advice useful for operation. Indicates situations that are potentia lly hazardous to the human body or devices. Indicates situations that are pote ntially extremely hazardous to the human bo dy or devi ces. Indicates operations that can be perf ormed or are effective only when the required option unit is installed. Note Caution[...]

1-1 Chapter 1 Using the Oper ator P a nel 1 This chapter explains the following topics: • Understanding the Operator P anel • Printing T est P ages • P aper Handling • P agination •e - M P S •I n t e r f a c e • Operating the Storage Device • Configu ration[...]

Understa nding the Operator Panel 1-2 Under standing the Oper ator P anel The operator panel has a LCD message display , three indicators, and eight keys. Messages that appear on the displ ay and functions of indicators and keys are explaine d in the sections that foll ows. Message Display The message displa y gives information in the form of short[...]

Understa nding the Operator Panel 1-3 Interface Indica tor The interface indicator shows the interf ace that is currently us ed. It uses the following abb reviations: PAR Standard bi-directional parallel interface USB Standard USB interface SER Option serial interface ( RS-232C) OPT Option network interface card --- No interface is active. Each int[...]

Understa nding the Operator Panel 1-4 Pa pe r Ty pe I n di c at or This shows the paper type defined for the current paper casette. Automatic cassette switchin g is availabl e according to the pa per type. The paper type can be specified at the op erator panel. See Creating Custom P aper T ype on page 1-32 . The follow ing abbrevi ations are us ed [...]

Understa nding the Operator Panel 1-5 Ke y s The operator panel keys are used to configure the p rinter . Note the certain keys have the secondary function. Settings made with thes e keys effect only the interface current ly in use. GO CANCEL MENU ENTER ? Note Key Function • Switches the printer on-line and off-line. • Prints and feed out one p[...]

Understa nding the Operator Panel 1-6 Menu System R oad Map This section explains how to use the menu selection system. The MENU key on the operator panel allows you to use the menu to set or change the printer environment such as the number of copies to make, emulation, etc., to your specif ic needs. Settings can be made when Ready is indicated on[...]

Understa nding the Operator Panel 1-7 Continued on next page Continued fr om previous page >NetWare > On Nibble (high) High Speed Normal >Parallel I/F Auto >NetWare Off On >TCP/IP Off >Ether Talk Off >OPT. StatusPage Off >>NetWare Frame Auto >>DHCP OFF >>IP Address >>Subnet Mask >>Gateway Emulation[...]

Understa nding the Operator Panel 1-8 Continued on next page Continued fr om previous page Ignore LF CR and LF On Landscape Regular Font > >>Courier Dark Dark >>Letter Gothic Regular >>Size 012.00 >>Pitch 10.00 cpi >List of Internal Fonts Page Set > >Copies 001 >Orientation Portrait >Page Protect Auto >L[...]

Understa nding the Operator Panel 1-9 Continued on next page Continued fr om previous page Hard Disk > >Read Data >Write Data >Delete Data >List of Partitions RAM Disk Mode On RAM Disk Mode Off >RAM Disk Size >Read Data >Write Data >Delete Data >List of Partitions >Read Fonts >Read Data >Write Data >Delete [...]

Understa nding the Operator Panel 1-10 Continued on next page Continued from Previous page >MP Tray Mode Cassette Paper Handling > >MP Tray Size A4 or Letter >MP Tray Type Plain >EF Size DL or Business >EF Type Envelope inch >>Unit mm >>X Dimension >>Y Dimension >Cassette Type Plain >Duplex Mode None >Ov[...]

Understa nding the Operator Panel 1-1 1 On >>Duplex Off Continued fr om previous page Perm / Temp Others > >Form Feed Time Out 030sec. >Sleep Timer > 015 min. >Print HEX-DUMP >Printer Reset Permanent >Resource Prot. Off Off >Buzzer On >Service > Mode Off >Auto Continue > Mode On >>Auto Continue Timer [...]

Printing T e st Pages 1-12 Printing T est Pages This section explains the proc edure for printing the printer’ s internal information using t he menu selection system. The menu map is useful l as a reference to guide yourself through the menu selection system. The status page is a list of p aramete rs and settings for most basic printer configura[...]

Printing T est Pages 1-13 MENU MAP FS-1920 P age Printer Sample MENU MAP[...]

Printing T e st Pages 1-14 Status P age If you want to check the printer' s current status, including memory available and option set tings, you ca n find the in formation you ne ed on the status page. 1 Press the MENU key . 2 Press the or key repeatedly until Print Status Page appears. 3 Press the ENTER key . A question mark ( ? ) appears. 4 [...]

Printing T est Pages 1-15 The follow ing is a sample status page. The numbers below refer to the contents explained on the following pages. Items and values on the st atus pa ge may vary depending on the printer’ s firmware version. KIR T est pattern ON Memory Installed Options Network Status Emulation T oner Gauge 0 100 Interfaces Hardware Inf o[...]

Printing T e st Pages 1-16 1 — Software V e rsion This information show s the firmware version and date of issue of the printer . 2 — Hard ware Infor mation This information sh ows various printer s ettings, such as the size and type of the paper in the paper cassette s. 3 — Memor y This shows the amount of total mem ory installe d in the pri[...]

Printing T est Pages 1-17 10 — Interface Infor mation This informatio n shows the default font a nd the default emu lation for a ll interfaces installe d in the printer . 11 — KIR T est Patter n KIR is the Kyocera Mita’s original sm oothing function. This test pattern shows the e ffect of t he KIR ( K yo cera Image Refinement) system.[...]

Printing T e st Pages 1-18 Ser vice Status Page The service statu s page contai ns printe r settings information that is more detailed than the standard status pag e and is therefore for mostly service purposes. However , since there is a great deal of information available on the service status page that may be helpful to you, the procedure for pr[...]

Printing T est Pages 1-19 Network Car d Interface Status P age T o use this function, the network interfac e card must be inst alled on the printer . Y ou can print out a status page for the network interface. The network interface card status page shows th e firmware versio n, the network addresses, and other inf ormation under various networ k pr[...]

Printing T e st Pages 1-20 7 The default setting is On . If it is set to Off , change it as follows. Press the ENTER key . A blinking question mark ( ? ) appears. 8 Select On using the or key . 9 Press the ENTER key agai n. 10 Press the MENU key . The message display returns to Ready . >Opt. StatusPage ? Off >Opt. StatusPage ? On >Opt. Sta[...]

Printing T est Pages 1-21 Fo n t L i s t s T o help in selecting fonts, you can print th e lists of the fonts including option fonts. 1 Press the MENU key . 2 Press the or key repeatedly until Font > appears. 3 Press the > key . 4 Press the or key repeatedly until > Font Select> appears. 5 T o print a list of the internal fonts, check t[...]

Printing T e st Pages 1-22 F ont Lists Internal Scalable and Bitmapped Fonts List Font Name Scalable/Bitmap Passwo rd Selection [FSET] Font ID PRESCRIBE Internal Scalable and Bitmapped Fonts List Font Name Scalable/Bitmap Passwo rd Selection [FSET] Font ID PRESCRIBE[...]

Printing T est Pages 1-23 R eceiv ed Data Dumping It is possible to print data received by the printer as he xadecimal code for the purposes of debugg ing programs and files. 1 Press the MENU key . 2 Press the or key repeatedly until Others > appears. 3 Press the > key . 4 Press the or key repeatedly until > Print HEX-DUMP appea rs. 5 Pres[...]

Paper Handling 1-24 Paper Handling This section explains how to use the operator panel to change the paper size and type for each paper source, the mode for the MP (multi-purpo se) tray , and other settings regarding paper handl ing. Setting the Paper Size Set the paper sizes accord in g to the sizes of paper to be set in the paper cassette and the[...]

Paper Handling 1-25 Custom Paper Size In addition to the standard sizes A5, A4, B5, Letter , and Legal (for U. S. A. only) size for the paper ca ssette, p aper of ot her sizes can be fed as custom sizes. When placing paper of sizes ot her than A5, A4, B5, Letter , or Legal (for U. S. A. on ly) into the pa per cass ette, set the size of the paper to[...]

Paper Handling 1-26 4 Press the or key repeatedly until >Cassette Size > appears. If option pap er feeders are adde d, Cassette 1 Size will appear for the standard pape r cassette and Cassette 2 Size , Cassette 3 Size , and Cassette 4 Size will appear for the option paper feeders. 5 Press the ENTER key . A blinking question mark ( ? ) appears[...]

Paper Handling 1-27 Selecting the Unit of Mea surement Then, use the following procedure to set the unit of measurement. 1 Press the > key . 2 Press the or key repeatedly until >>Unit appears. The uni t of measurement can be selected betw een millimeters and inches. The current unit of measurement is displayed ( the default setting is mm )[...]

Paper Handling 1-28 1 When the unit of measuremen t is set, press the key . >>X Dimension appears as sh own below (the paper w idth setting). 2 Press the ENTER key . A blinking cursor ( ) appears. 3 Press the or key to increase or decre ase the value of the figure where the cursor is blinking and display the desi red width. The width can be s[...]

Paper Handling 1-29 3 Press the > key . 4 Press the or key repeatedly until >MP Tray Size appears. 5 Press the ENTER key . A blinking question mark ( ? ) appears. 6 Press the or ke y to display the desired MP tray size. The display changes as shown below . A4 Executive Letter Legal Custom Oficio II Statement Folio Youkei 2 Youkei 4 16K Hagaki[...]

Paper Handling 1-30 Setting the Paper T ype Set the paper types accordin g to the paper to be set in the cassette and the MP tray . Setting the Paper Type in P aper Cassette Make this setting to match the paper type fed from the paper cass ette of the printer . If the paper type is se t correctly , you can perform printing using the media type sele[...]

Paper Handling 1-31 Setting the Paper Type in MP T ray Y ou can automatically select the pape r cassette according to the selection made by the application software (printer dri ver). The factory default setting is Plain . This menu does not appears when the opti on envelope feeder is installed on the printer . F or more details about the paper typ[...]

Paper Handling 1-32 6 Press the or key to display the desired M P tray type. The display changes as shown below . Plain Transparency Preprinted Labels Bond Recycled Vellum Rough Letterhead Color Prepunched Envelope Cardstock Thick High quality Custom ( 1 to 8 ) 7 When the desired MP tray type is di splayed, press the ENTER key . 8 Press the MENU ke[...]

Paper Handling 1-33 5 Press the ENTER key . A blinking question mark ( ? ) appears. 6 Press the or key to display the desired p aper type. The disp lay changes as shown below . Custom ( 1 to 8 ) Plain Transparency Preprinted Labels Bond Recycled Vellum Rough Letterhead Color Prepunched Envelope Cardstock Thick High quality 7 When the paper type to [...]

Paper Handling 1-34 Setting the Paper W eight Y ou can set the paper thickness for your custom paper type to be customized. 1 Display the custom paper type (see Creating Custom Pa per Type on page 1-32 ) and press the > key . 2 Press the or key repeatedly until >>Paper Weight appears. 3 Press the ENTER key . A blinking question mark ( ? ) [...]

Paper Handling 1-35 Setting the Duplex Pa th T o use this function, the duplexer must be inst alled on the printer . If the paper type is set to Custom and the option duplexer is installed on the printer , you can set whether or not to enable duplex pri nting as fol lows. The default setting is Enable . 1 Display the custom paper type (see Creating[...]

Paper Handling 1-36 Resetting the Custom Paper Type Resets the settings of Custom 1 to 8 that are set in Creating Custom P aper T ype on page 1-32 . 1 Press the MENU key . 2 Press the or key repeatedly until Paper handling > appears. 3 Press the > key . 4 Press the or key repeatedly until >Reset Type Adjust appears. 5 Press the ENTER key .[...]

Paper Handling 1-37 MP T ray Mode The MP tray can be used in either of two modes – first or cassette . The MP tray feed paper differently depending on the mode: • Cassette Mode This is the de fault mode. The MP tray acts in the same manner as other paper source. The printer can co rrectly feed paper from any paper source as you command on the p[...]

Paper Handling 1-38 5 Press the ENTER key . A blinking question mark ( ? ) appears. 6 Select First or Cassette using the or key . 7 Press the ENTER key . 8 Press the MENU key . The message display returns to Ready . Selecting the P aper F eed Source Y ou can select from which paper source printing will be performed. If no option units are installed[...]

Paper Handling 1-39 Selecting the Output Stac k The follow ing procedure allows you to select whether pri ntouts will b e received by the top tray or to the rear tr ay . If an option sorter is installed, it can also be selected usin g the manner described below . 1 Press the MENU key . 2 Press the or key repeatedly until Paper Handling > appea r[...]

Paper Handling 1-40 Ov er riding A4 and Le tter Size Difference This selects whether to enable or di sable the difference between A4 size and Letter size. Under th e default setting of Off , the paper size of the paper source is matched to the paper size formatting the jobs. If these differ , a corres ponding error message is displayed. When this i[...]

Pagination 1-41 P agination The items regardi ng pagination can be made from the opera tor panel. The items that can be set are shown below . • Emulation •F o n t • Code Set •N u m b e r o f C o p i e s • Printing Orientation • KIR (Kyocera Ima ge Re finement) •E c o p r i n t • Resolution Emulation The following proce dure allows y[...]

Pagination 1-42 5 Press the ENTER key . 6 Press the MENU key . The message display returns to Ready . Alter nativ e Emulati on for KPDL Emula tion The auto K PDL ( KPDL (AUTO) ) emula tion enables the printer to automatically change the emulation mode according to the print job received. The alternative emulation ca n be selected using the operator[...]

Pagination 1-43 8 Press the or key repeatedly until the desired alternative emulation appears. 9 Press the ENTER key . 10 Press the MENU key . The message display returns to Ready . Printing KPDL Er r or s The printer can print error descriptions when prin ting e rror occurs during KPDL emulation. Th e default is Off – the printer does not print [...]

Pagination 1-44 8 Select On using the or key . 9 Press the ENTER key . 10 Press the MENU key . The message display returns to Ready . Fo n t Y ou can select the default font for the current interface. In addition to the internal fonts, all fonts that are down loaded to the printer memory , or fonts stored on a CompactFlash card, Microdriv e, or opt[...]

Pagination 1-45 6 Press the > key . The message display ch anges to that show below . The letter before the number indica tes the type of font as shown below: 7 Press the ENTER key . A blinking question mark ( ? ) appears. 8 Press the or key repeatedly until the desired font number appears. F or font numbers of the internal fonts, see List of F [...]

Pagination 1-46 Default F ont Siz e The followin g procedure determin es th e size of the default font. If the default font is a fixed font su ch as Courier or Letter Gothic, the character pitch can be changed instea d of the font size. 1 Press the MENU key . 2 Press the or key repeatedly until Font > appears. 3 Press the > key . 4 Press the [...]

Pagination 1-47 Changing Type f or Courier/Letter Gothic Courier or Letter Gothic font type can be selected as R egular or Dark. F or example, to change the type of Courier , proceed as follows: 1 Press the MENU key . 2 Press the or key repeatedly until Font > appears. 3 Press the > key . 4 Press the or key repeatedly until >Font Select &g[...]

Pagination 1-48 Setting the Char acter Pitch for Courier/Letter Gothic The character pitch for fixed fonts is adjustable when the default font is Courier or Letter Gothic. 1 Press the MENU key . 2 Press the or key repeatedly until Font > appears. 3 Press the > key . 4 Press the or key repeatedly until >Font Select > appears. 5 Check tha[...]

Pagination 1-49 Code Set Y ou can change the character code set. Av ailable character cod e sets vary depending on the current font. (The default is IBM PC-8 .) 1 Press the MENU key . 2 Press the or key repeatedly until Font > appears. 3 Press the > key . Press the or key unti l > Code Set appears. 4 Press the ENTER key . A blinking questi[...]

Pagination 1-50 Number of Copies Y ou can set the number of copies to be printed of each page for the current interface. The number of copies can be set betwee n 1 and 999 . 1 Press the MENU key . 2 Press the or key repeatedly until Page set > appears. 3 Press the > key . 4 Press the or key repeatedly until >Copies appears. 5 Press the ENT[...]

Pagination 1-51 Printing Orienta tion The default orientation of the pag e can be selected from the portrait (upright) and landscape (si deways) page orientation. 1 Press the MENU key . 2 Press the or key repeatedly until Page Set > appears. 3 Press the > key . 4 Press the or key repeatedly until >Orientation appea rs. 5 Press the ENTER ke[...]

Pagination 1-52 KIR (K yocera Image R efinement) This printer incorporates the KIR (K yocera I mage Refinement) smoothing function. This function pr ovides high print quality by providin g software enhancement of print resolution. Set the print density to 3 whe n setting the KIR mode. For det ails on print density , see page 1-95 . L ook at the che[...]

Pagination 1-53 1 Press the MENU key . 2 Press the or key repeatedly until Print Quality > appears. 3 Press the > key . 4 Press the or key repeatedly until >KIR Mode appears. 5 Press the ENTER key . A blinking question mark ( ? ) appears. 6 Select On or Off using the or key . 7 Press the ENTER key . 8 Press the MENU key . The message displ[...]

Pagination 1-54 Ecoprint The Ecoprint ena bles you to reduce the amou nt of toner consumed on the page so as to save your printing costs. Y ou can set to Ecop rint mode on, as follows. (The factory default setti ng is Off .) The Ecoprint setting has no effe ct on the print spee d. The Ecoprin t mode setting is On when the printing image becomes lig[...]

Pagination 1-55 Re s o l ut i o n Proceed as follows to set the default print resolution from three ways — 300 dpi , 600 dpi , and Fast 1200 mode . The clarity of printed characters and g raphics beco mes sharper in this order . 1 Press the MENU key . 2 Press the or key repeatedly until Print Quality > appears. 3 Press the > key . 4 Press t[...]

e-MPS 1-56 e-MPS e-MPS is an a bbreviation for ‘enhanced-M ultiple Printing System’ which implements the following functions that are availa ble from the printer driver: • Job R etention • Job Storage In either job mode, when printing a do cument, the print data is transferred from the computer to the printer then stored on the printer’s [...]

e-MPS 1-57 Job Storage Job storage stores print jobs either te mporarily or permanently , or in virtual mailboxes, as you click an appropriate rad io button on the printer driver when printing from a computer . Vir tual Mailbox Virt ual mailbox is part of Job Storage, which stores pri nt jobs on the Virt ual mailbox is part of Job Storage, wh ich s[...]

e-MPS 1-58 3 Press the > key . 4 Press the or key repeatedly until >Quick Copy appears followed by the user name ( Harold , in this example). The user name is assigned at printing u sing the printer d river . 5 Press the ENTER key. A blinking question mark ( ? ) appears before the user name. 6 Press the or key to disp lay the desire d user na[...]

e-MPS 1-59 Deleting a Quick Cop y J ob All quick copy jobs are automa tically de leted when the printer is turned off . If you desire to explicitly delete a stored quick copy job , proceed as follows: 1 Follow steps 1 through 8 i n the above section to let the title of the job displayed. 2 When the title of the jo b is displayed, e .g. Report , bel[...]

e-MPS 1-60 4 Press the or key repeatedly until >Quick Copy appears followed by the user name ( Harold , in this example). The user name is assigned at printing u sing the printer d river . 5 Press the ENTER key. A blinking question mark ( ? ) appears before the user name. 6 Press the or key to disp lay the desire d user name, Arlen , in this exa[...]

e-MPS 1-61 Printing a Private Job In private printing , you can specify that a job is not printed until you release the job fr om the operator pa nel. A t sending the jo b from the application software, you sh oul d specify a 4-digit access code i n the printer driver . The job is re leased for printing by entering the access code on the operator p[...]

e-MPS 1-62 8 Press the or key to di splay the desired job title. 9 Press the ENTER key . The ID input line ap pears. Enter the four-digit access code entered in the printer driver and press the ENTER key . T o enter the ID, press the < or > key to move the cursor to the number to be changed and t hen ente r the correct number by pressing the [...]

e-MPS 1-63 Printing a Stored J ob The procedure below allows you to store print jobs to the Microdrive that are frequently needed such as fax cove r pages, check lists, and order forms, for printing at any later time using the operator panel. The print jobs will not be delete d when the printe r is turned off . Releasing a St ored Job T o print a s[...]

e-MPS 1-64 8 Press the or key to di splay the desired job title. 9 Press the ENTER key . If you entered an access code for the printer driver , the ID in put line appears. Ente r the four-d igit access code entered in the printer driver and press the ENTER key . T o enter the ID, press the < or > key to move the cursor to the number to be cha[...]

e-MPS 1-65 Printing a Code J ob KM-NET Job Manager Install the KM-NET Job Manager soft ware from the CD -R OM supplied with the printer . T o do this, from the CD-ROM Main Menu , select Printer Utilities > Install KM-NET Job Manager . 1 Browse through W indows St ar t > Programs > KYOCERA MIT A > KM-Net > Job Manager . 2 Enter the pa[...]

e-MPS 1-66 5 Double click Model Name on the list. The jobs currently stored in the printer are shown. T o print the job, right click Job name and then click Print on the drop down list that appears. It is possible to select more than on e job at a time by right clicking a job one by one wh ile pressing the Shift key on the computer keyboard. The jo[...]

e-MPS 1-67 Printing a List of Code J obs If you select P ermanent Job Storage on the printer driver , you can have a List of Code Job printed using the operator panel. 1 Press the MENU key . 2 Press the or key repeatedly until e-MPS > appears. 3 Press the > key . 4 Press the or key repeatedly until >List of Code JOB appears. 5 Press the EN[...]

e-MPS 1-68 R etrie ving J obs from V ir tual Mailbo x (VMB) T o use this mode, an option Microdriv e must be inst alled in the printer . T o retrieve the jobs posted in the virtual mailbox, proceed as follo ws. 1 Press the MENU key . 2 Press the or key repeatedly until e-MPS > appears. 3 Press the > key . 4 Press the or key repeatedly until &[...]

e-MPS 1-69 Printing a List of VMB A V irtual Mailbox list i ncludes the jo bs currently stored in the mailboxes. 1 Press the MENU key . 2 Press the or key repeatedly until e-MPS > appears. 3 Press the > key . 4 Press the or key repeatedly until >List of VMB appea rs. 5 Press the ENTER key . A question mark ( ? ) appears. 6 Press the ENTER [...]

e-MPS 1-70 e-MPS Configura tion Y ou can change the following pa rameters for e-MP S operation: • Maximum number of Quick Copy/Proof and Hold jobs • Maximum space assigned to temporary code jobs • Maximum space assigned to permanent code jobs • Maximum space assigned to virtual mailboxes The tot al amount of storage area s specified must no[...]

e-MPS 1-71 8 Press the or key to increase or decrease the value at th e blinking cursor . The value can be set between 0 and 50. Use the > and < keys to move the cursor right and left. 9 When the desired maximum number of jobs is set, press the ENTER key . 10 Press the MENU key . The message display returns to Ready . Maximum Space Assigned t[...]

e-MPS 1-72 8 Press the or key to increa se or decreas e, respectiv ely , the valu e at the blink ing cursor . Use the > and < keys to move the cursor right and left. 9 When the desired size is displayed, press the ENTER key . 10 Press the MENU key . The message display returns to Ready . Maximum Space Assigned to Per manent Code J obs This ch[...]

e-MPS 1-73 9 When the desired size is displayed, press the ENTER key . 10 Press the MENU key . The message display returns to Ready . Maximum Space Assigned to V ir tual Mailbo xes This changes the Microdrive space fo r virtual mail boxes. Y ou can change the maximum space from 0 to 9999 (m egabytes). The actual maximum size depends on the size of [...]

Interface 1-74 Interface The printer is equipped with bot h a parallel and USB interfa ce. Option serial interface board kit and network in terface card can also be installed. V arious printing environment parameters such as the default emulation can be changed indepently on different interfaces by using the printer’s menu selection system. Befor[...]

Interface 1-75 6 Press the ENTER key . A blinking question mark ( ? ) appears. 7 Press the or key to display the desired mode. Th e display changes as shown below . Press the ENTER key . Auto (default) Normal High Speed Nibble (high) 8 Press the MENU key . The message display returns to Ready . USB Interface Mode About USB interface, for details, s[...]

Interface 1-76 Serial Interface P arameter s This section applies to the pr inters having t he option serial int erface board kit (IB-1 1) installed. The baud rate, data bits, stop bits, pari ty , and protocol for the serial interface can be set as follows: 1 Press the MENU key . 2 Press the or key repeatedly until Interface > appears. One of th[...]

Interface 1-77 6 Press the > key . Each time the or ke y is pressed, the setting item and current setting change as sh own below . 7 Display the setting item to be changed and press the ENTER key . A question mark ( ? ) appears. The following example explains ho w to change the baud rate. The settings for other items can be changed in a similar [...]

Interface 1-78 Network Interface Parameter s This section applies to the pr inters hav ing the option network card installed. T o make your printer supports TCP/IP , Netware, and EtherT alk networks, you will n eed to install the option netw ork interfac e card in the printer and make the proper settings as explained in this section. Using the oper[...]

Interface 1-79 6 Press the > key . Each time the or key is pressed, the display changes as shown below . 7 The following example explains how to activate TCP/IP protocol to connect the printer in the network. Y ou can select Netware or EtherTalk in a similar manner . If TCP/IP is currently Off is displayed, sele ct On using the or key . Press th[...]

Interface 1-80 8 Press the > key . Each time the or key is pressed, th e item changes as shown below . 9 Display the item to be set and press the ENTER key . Fo r DHCP , a question mark ( ? ) appears. F or IP Address , Subnet Mask , and Gateway , the cursor ( ) blinks. 10 Fo r DHCP , select On or Off using the or key . F or IP Address , Subnet M[...]

Operating the S torage Device 1-81 Oper a ting the Stor a ge De vice The printer supports three types of storage devices: CompactFlash card, Microdrive, and RAM disk. The printer is equipped with a sl ot for a CompactFlash card and a Microdrive. By inserting a CompactF lash card or Microdrive into the printer , the following operatio ns beco me ava[...]

Operating the S torage Device 1-82 3 The default setting is Off . P ress the ENTER key . A blinking question mark ( ? ) appears. Select On using the or key , and then press the ENTER key . 4 Press the > key to disp lay >RAM Disk Size . 5 Press the ENTER key again, and change the RAM disk size using the or key . It is not possible to make a se[...]

Operating the S torage Device 1-83 R eading Da ta T o read data on a Comp actFlash card, Microdrive, or the RAM disk use the following procedure: 1 Press the MENU key . 2 Press the or key repeatedly until Memory Card > , Hard Disk > or RAM Disk Mode > appears. 3 Press the > key . 4 Press the or key repeatedly until >Read Data appears[...]

Operating the S torage Device 1-84 Writing Data Y ou can write data to a CompactFlash card, the Microdrive, or the RAM disk using the operator panel. When writing data to the storage device, a name is automatically assigned to th e data. The CompactFlash card or the Microdrive or the RAM disk must be formatted. Otherwise, the >Write Data message[...]

Operating the S torage Device 1-85 7 In this state, send the file fr om the computer to the printer . The file is written onto the storage device given a desti nation name (also referred to as a partition na me) which the printer automatically assigns one after an other as fo llows: DataS001 (fi rst data), DataS002 (second da ta), DataS003 (third d[...]

Operating the S torage Device 1-86 9 Repeat above steps until you have transferred all data (files) that you want to write to the CompactF lash card. Each time you finish writing data, a CompactFlash card write informat ion page is pr inted from the printer s howing the in formation ex plained in ste p 4 above, but pertaining only to the da ta just[...]

Operating the S torage Device 1-87 R eading F onts from a CompactFlash Car d If a font (CompactFlash) card is alre ady inserted into the sl ot when the printer is turned on, the fonts are au tomatically read into the printer . T o re-read fonts into the printer from a Comp actFlash card , proceed as follows. 1 Press the MENU key . 2 Press the or ke[...]

Operating the S torage Device 1-88 F o r ma tting a Storage Device A new CompactFlash card or Microdrive must be form atted before it can be used in the p rinter . Y ou can format the storag e device usin g the prin ter operator p anel. • Formatting will destroy an y existing dat a on a storage dev ice. • Y ou can format th e Microdrive using t[...]

Operating the S torage Device 1-89 When the formatting is successfully completed, the printer automatically prints out a format informa tion page as shown be low . Capacity. The total size of the CompactFla sh card or the Microdrive memory . Used Space. The size the printer uses for its system. Free Space. The size remain ing in the CompactFla sh c[...]

Operating the S torage Device 1-90 5 Press the ENTER key . A question mark ( ? ) appears. 6 Press the ENTER key . Processing appears and the printing of the list starts. The list provides the follow ing information that are automati cally generated by the printe r ab out data currently stor ed in the stora ge device: Device Name/Number. Description[...]

Configuration 1-91 Configuration This section explains the detai ls of printer settings. The following it ems are covered. • P age Protect Mode • Linefeed (LF) Action • Carriage-Return (CR) Action •W i d e A 4 P i t c h • Print Density • T otal Pri nted P ages • T oner Co unter Resetting • Message Language • Automatic F orm F eed [...]

Configuration 1-92 5 Press the ENTER key . A blinking question mark ( ? ) appears. 6 Press the or key repeatedly until Auto appears. 7 Press the ENTER key . 8 Press the MENU key . The message display returns to Ready . Linefeed (LF) Action This procedure instructs the printer what to do when it receives a linefeed code (character code 0AH). 1 Press[...]

Configuration 1-93 7 When the desired action is displayed, press the ENTER key . 8 Press the MENU key . The message display returns to Ready . Car ria ge-Retur n (CR) Action This procedure instru cts the printer what to do when it receives a carriage- return code (cha racter code 0DH) 1 Press the MENU key . 2 Press the or key repeatedly until Page [...]

Configuration 1-94 W ide A4 Pitch Turn th is to On to increase the maximum number of characters that can be printed in a line for A4 page (78 characters at 10 pitch) and Let ter size page (80 characters at 10 pitch). This setting is effective in only PCL 6 emulation. 1 Press the MENU key . 2 Press the or key repeatedly until Page set > appears. [...]

Configuration 1-95 Print Density The print density can be adjusted in fiv e steps: from 01 (l ight) to 05 (dark). The factory setting is 03 . 1 Press the MENU key . 2 Press the or key repeatedly until Print Quality > appears. 3 Press the > key . 4 Press the or key repeatedly until >Print Density appears. 5 Press the ENTER key . A blinking [...]

Configuration 1-96 T o tal Printed Pages This procedure displays the total number of printed pages. 1 Press the MENU key . 2 Press the or key repeatedly until Life Counters > appears. 3 Press the > key . 4 Press the or key repeatedly until >Total Print appears, the total number of printed pages displayed. 5 Press the MENU key . The message[...]

Configuration 1-97 5 Press the ENTER key . A question mark ( ? ) appears. 6 Press the ENTER key . The toner counter is reset. The message display returns to Ready . Message Langua ge Y ou can select the language of the messages on the me ssage display by following the procedure given below . Y o u can optionally download messag es in order language[...]

Configuration 1-98 6 Press the key . The display cycles through the available selections in the followin g order (The ke y cycles in the reverse order): 7 Press the ENTER key . 8 Press the MENU key . The message display returns to Ready . >MSG Language ? English >Langue ? Francais >Anzeigesprache ? Deutsch >Lingua ? Italiano >Bericht[...]

Configuration 1-99 Automa tic F or m F eed Timeout When the printer receives no data for a certain time, it time out and releases the current interface: it prints whatever data it has in its buffer and feeds out the page. Y ou can adju st the time-out time as follows: 1 Press the MENU key . 2 Press the or key repeatedly until Others > appears. 3[...]

Configuration 1-100 Sleep Timer Setting The printer has a sleep timer to cons erve power when the printe r is not printing, processing, or receiving data . Y ou can adjust the timer value, the length of time the printer waits be fore entering sleep ing mode in the absence of data. 1 Press the MENU key . 2 Press the or key repeatedly until Others &g[...]

Configuration 1-101 T ur ning Of f the Sleep Timer Y ou can turn off the sleep timer function by following the pr ocedure given below . 1 Press the MENU key . 2 Press the or key repeatedly until Others > appears. 3 Press the > key . 4 Press the or key repeatedly until >Sleep Timer > appears. 5 Press the > key and displa y >>Sle[...]

Configuration 1-102 Printer R esetting The procedure described below reset s the printer’s temporary conditions, such as the current unit of measurem ent, page orientation, font, character code set, margins, etc., set by commands to their default values. 1 Press the MENU key . 2 Press the or key repeatedly until Others > appears. 3 Press the &[...]

Configuration 1-103 R esource Pr otection When you switch from the PCL 6 emulation to another , all downloaded fonts and macros are lost. R esource protection preserves these PCL resources in memory so that they are intact when you change the emulation back to PCL 6. Resource protect ion requires extra memory to store the down loaded font s and mac[...]

Configuration 1-104 Alar m (Buzzer) Setting In addition to the message displayed when the paper supply is exhausted, or when paper jamming occurs, an au dio warning is made to sound. This is useful, for example, when the printer is in a location some distance from the user . The audio alarm is set to On when leaving the factory . If the alarm is se[...]

Configuration 1-105 Auto Continue Setting When Auto Continue is enabled, the printer will automatically print the next received data following a pres et amount of time passe s after any one of the foll owing errors occurs: Memory overflow Press GO Print overrun Press GO KPDL error Press GO File not found Press GO Hard disk err Press GO RAM disk err[...]

Configuration 1-106 Setting the Auto Continue R eco v er y Time F ollow the procedure given below to change the recovery time for Auto Continue. 1 Press the MENU key . 2 Press the or key repeatedly until Others > appears. 3 Press the > key . 4 Press the or key repeatedly until Auto Continue Mode > appears. 5 Press the > key and display [...]

Configuration 1-107 Duplex Printing Err o r Detection Setting If the error detection setting for duplex printing has be en turned On , and you attempt to print onto a paper size and paper type that cannot be used for duplex printing, the Duplex disabled Press GO error message will be displayed and printing will stop. T o print onto one-side of the [...]

2-1 Chapter 2 P a per Selection 2 This chapter explains the following topics: • General Guidelines • Special P aper •P a p e r T y p e[...]

General Guidelines 2-2 Gener al Guidelines The printer is designe d to print on high-quality copier bond paper (the kin d used in ordinary dry copi er mach ines), but it can also accept a variety of other types of paper within the limits specified below . The manufacturer assu mes no liability for problems that occ ur when pa per not satisfying the[...]

General Guidelines 2-3 Selecting the Right P aper Laser printing is a process in volving laser light, electr ostatic discharge, toner , and heat. In addition, as the paper passes through the printer it undergoes cons iderable slidin g, bending, and twisting moti ons. A high- quality printing paper matching the pr inter’s requirements withstan ds [...]

General Guidelines 2-4 Paper Size Cassettes and an MP tray are available for the paper si zes listed in the table below . The dimensional tolerances are ±0.7 mm (±0.0276 inches) for the length and width. The angle at the corners must be 90° ±0.2°. Smoothness The paper should have a smooth, uncoa ted surface. P aper with a rough or sandy surfac[...]

General Guidelines 2-5 Paper Weight Equivalence T a ble P aper weight is listed with expression in U.S. bo nd weight (lb) and European metric (g/m²). Th e shaded point indicates the standard weight. T hickness (Caliper) Thick paper is referred to as high-caliper paper and thi n paper as low- caliper paper . The paper us ed with the printer shou ld[...]

General Guidelines 2-6 Paper Grain When paper is manufactured, it is cut into sheets with the grain running parallel to the leng th (long grain) or parallel to the width (short grain). Short grain paper ca n cause feeding p roblems in the prin ter . All paper used in the printer should be long grain. Other Paper Proper ties Porosity: Refe rs to the[...]

S pecial Paper 2-7 Special Paper This section explains prin ting on special pap er . The page printer can use the following types of special paper . In this case, set the media type according to the table below . When using the above types of paper , be sure to use products that are specified for use with photocopiers an d/or page printers. F eed p[...]

S pecial Paper 2-8 Adhesiv e-Back ed Labels The basic rule for printing on adhesive l abels is that the adhesive must never come into contact with any pa rt of the printer . Adhesive paper sticking to the drum or rollers will damage the printer . Be sure to feed label p aper from the MP tr ay . Feeding label p aper from a pa per casset te may cause[...]

S pecial Paper 2-9 The table below lists the specifications f or adhesive label paper . Postcards F an the stack of postcards and align the edges before loadi ng them in the MP tray . Make sure the postcards yo u are going to set are not curled. F eeding curled postcards may cause paper jams. Some postcards have roug h edges on the back (those are [...]

S pecial Paper 2-10 T o avoid jamming due to curled envelopes, do not leave mor e than approximately 10 printed envelop es stacked in the paper trays durin g multiple enve lope printing. Envelopes should be fed in the fac e-up position, right edge first. T hick P aper F an the stack of paper and align the edges before loadi ng them in the MP tray .[...]

S pecial Paper 2-1 1 Colored Paper Colored paper should satisfy the same conditions a s white bond p aper , listed i n P aper Specifications on page 2-2 . In additi on, the pigment s used in the paper must be able to withstand the heat of fusing during the printing process (up to 200 °C or 392 °F). Preprinted Paper Preprinted paper should have a [...]

Paper T ype 2-12 P aper Type The printer is cap able of printing under the optimum setting for the type of paper being used. Setting the paper type fo r the paper source from the printer’s operator panel will cause the printer to automa tically select the paper source and print in the mode best suited to that type of paper . A different paper typ[...]

3-1 Chapter 3 Maintenance 3 This chapter explai ns how to replace th e toner container and how to clean parts such as the registration roller and charger wire. This chapter explains the following topics: • T oner Container Replacemen t • W aste T oner Box Replacement •C l e a n i n g[...]

T oner Container Replac ement 3-2 T oner Container Replacement The toner container in the printer should be replaced as soon as the message display shows Toner low or soon after . If you continue to use the printer , eventually the to ner supply will be exhausted at which point the printer will stop printing and the Replace toner Clean printer mess[...]

T oner Container Replacement 3-3 R eplenishing T oner 1 Open the printer top cover all the way . 2 Pull the lock leve r (blue colored) to the right and gen tly lift the old toner container . Keep the toner cont ainer as level as possible while removing. 3 Put the old toner container in the plastic bag supplied with the toner kit and dispo se of it.[...]

T oner Container Replac ement 3-4 4 T ake the new toner container from the bag. 5 With th e label side d o wn, thoroughly shake th e toner container (in the direction of the arrows) ten time s or more. This ensures that the toner is evenly distributed in side. 6 Carefully remove th e protective seal (orange colored). 7 Install the toner container i[...]

T oner Container Replacement 3-5 8 Push firmly on the top of the tone r container at the positions marked PUSH HERE . When the toner container fi ts into pl ace, it will lock with a clicki ng sound. 9 Close the top cover . It is necessary to clean the inside of the printer af ter repla cing the toner cont ainer . If the toner cont ainer is replaced[...]

W aste T oner Box Replacement 3-6 Wa ste T oner Bo x R eplacement R eplacing the Waste T oner Bo x When replacing the toner con t ainer , the used waste toner box in t he printer should also be replace d with the new one from the new toner kit. 1 Open the left cover on the left side of the prin ter . 2 While holdin g the waste toner b ox, press the[...]

W aste T oner Box Replacement 3-7 3 Cap the waste toner box after removing from the printer . 4 T o avoid toner sp illing, place the capped w aste toner box in th e plastic bag supplied before proper disposal . 5 Open the cap of the new wa ste toner box. Cap Old Waste T oner Box Plastic Bag Cap New Waste To n e r B o x[...]

W aste T oner Box Replacement 3-8 6 Insert the new waste toner box as shown in the f igure below . The box will be locked when it fits into place. 7 Ensure that it is correctly in serted and close the left cover . The printer parts mu st be cleaned when replacing th e toner container . See Cleaning on page 3-9 . 8 When the toner container is replac[...]

Cleaning 3-9 Cleaning T o avoid print qu ality problems, the following printer parts must be cleaned with every toner container re placemen t. In addi tion, the charger wire and paper transfer unit should be cleaned from time to time, or whenever print quality problems occur . If the toner container was replaced wh en Replace toner Clean printer wa[...]

Cleaning 3-10 Cleaning the Charger Grid The charger grid is a part located at the bottom of the charger unit, which also needs to be cleaned. Y ou should use a grid cleaner attaching it to the printer and pull out the char ger unit as instructed below . 1 T ake the grid cleaner from protecti ve bag in the new toner kit, and remove the cap. The grid[...]

Cleaning 3-1 1 3 Attach the grid cleaner to the prin ter with the pad at the top, as shown in the figure. 4 Making sure that the charger roller does not come into contact with the grid cleaner pad, repeat a few tim es the act ion of slowly pulling out and pushing back in the charger unit, as shown in the fig ure. This cleans grid part underneath th[...]

Cleaning 3-12 5 Remove the grid cleaner from the pr inter and dispose of it. The grid cleaner is not re-usable. 6 After cleaning the charger wire an d grid, push the char ger unit all the way in and close the left cover .[...]

Cleaning 3-13 Paper T r ansfer Unit T o avoid print qu ality problems due to paper dust and debris, clea n the paper transfer unit in the following manner . 1 While pulling the paper transfer uni t release lever (green colored), pull out the paper transfer unit. 2 Wipe away the p aper dust on the registration roller and the paper ramp using the wip[...]

4-1 Chapter 4 T r oubleshooting 4 This chapter expl ains how to han dle printer pr oblems that may occur . If a problem cannot be corrected, contact your K yocera Mita dealer . This chapter explains the following topics: • General Guide • Print Quality Problems • Indicators and Messages • Correcting a P aper Jam[...]

General Guide 4-2 Gener al Guide There are quite a few printer problems that you can de al with by yourself. This section explains how to correct these problems. Therefore, if so me kind of prob lem should o ccur , check the following before concluding the printer is broken. If you still cannot correct a printer problem even afte r checking the abo[...]

Print Quality Problems 4-3 Print Quality Problems As the following table shows, the re are many possibl e causes of print quality problems, such as blank output as. The troubleshooting proce d ure for each type of problem is ex plain ed belo w . If you still ca n not solve the problem, contact your K yocera Mita dealer . Printed Results Corrective [...]

Print Quality Problems 4-4 F aint or blurred printing Check the Ecoprint setting. When this setting is On , switch it to Off on the Operator P anel. (See Ecoprint on page 1-54 ) Check the operator panel. •I f t h e Toner low message is displayed and the AT T E N T I O N indicat or is flashing, install a new toner kit. See T oner Container Repla c[...]

Print Quality Problems 4-5 Dirt on the top edge or back of the paper Check the paper chute and the ramp. Pull out the paper transfer unit and check for toner on the paper ramp. Clean the paper ramp using a soft, dr y , l int- free cloth. See Cleaning on page 3-9 . Check the transfer roller . If the transfer roller is dirt y with toner , try printin[...]

Indicators and Messages 4-6 Indicators and Messa ges The tables on the following pag es indicate how to respond to problems indicated by the operator panel in dicators and messages. Indicators Indicator Name Condition Description Rea dy indicat or Flashing A n error occurs that you can clear by yourself. Lit The printer is on-line. The printer is r[...]

Indicators and Message s 4-7 Maintenance Messages The following table lists maintena nce messages that you can deal with by y ourself . If Call service person appears, turn of f the printer , discon nect the power cord, and contact you r Kyocera Mita dealer . Message Corrective Acti on Add paper (paper source) The paper has run out. Supply paper ac[...]

Indicators and Messages 4-8 Load Cassette # (paper size) / (paper type) †† There is data for printing that matches with a paper ca ssette setting (paper si ze, paper type), but there is no paper in the paper cassette. Set paper into the paper source as displa yed on the operator panel, and press the GO key to restart printing. Howev e r , the p[...]

Indicators and Message s 4-9 Warning image adapt Printing job cannot b e done in current res o lution because there is not enough internal memory . Try adding more memory or changing resolution. See Appendix A . Warning low memory The printer’s internal memory is running lo w due to the number of fonts and macros downloaded. Print a status page t[...]

Indicators and Messages 4-10 Er r or Messa ges The following tab le lists error mess ages that can be deal t with by the user . Message Corrective Act ion File not found Press GO VMB: A VMB tray that was specified for outp ut does not conta in any jobs, or the VMB tray is not being used. Confirm the VMB tray . If Auto Continue is set to On , printi[...]

Indicators and Message s 4-1 1 Memory card err Insert again The CompactFlash card is accidentally removed from the printer’ s memory card slot during reading. If you continue re ading the memory card, inse rt the same memory card into the slot again. The printer agai n reads it from the beginning of the data. Note: We recommend that you follow th[...]

Correcting a Paper Jam 4-12 Cor recting a Paper Jam The Paper jam message is displayed on th e message display when paper becomes stuck in the paper transport system, the paper feed timing is incorrect, or paper fails to feed at all. The jam can be corrected by removing the paper . The printer goes off-line when the Paper jam message is displayed. [...]

Correcting a Paper Jam 4-13 When the jammed paper has be en remo ved, open and close the printer’s top cover or the paper tr ansfer unit. Then the pr inter automatically warms up, goes on- line, and co ntinues prin ti ng. Dependin g on the point at w hich the jam occurred, the printer may or may not print the jammed page. If paper jams occur freq[...]

Correcting a Paper Jam 4-14 Jam at th e Pa p e r C a ss e t te or Inside the Printer P aper is jammed at the paper cassette or inside the printer . R emove the jammed paper using the procedure given below . While the display alternates between the pap er jam message and HELP START , press the key . An online help message appears. 1 Pull out the pap[...]

Correcting a Paper Jam 4-15 3 If paper is jammed before the regist ration roller , remove it as shown in A . If paper is jammed under the regi stration roller , remove it as shown in B . 4 Open the rear cover and remove the jammed paper . 5 Push the paper cassette and paper transfer uni t back in and close the rear cover . Registration Roller Regis[...]

Correcting a Paper Jam 4-16 Paper J am at the Option Duple xer P aper is jammed inside the rear cover of the option duplexer or at the duplexer drawer . R emove the jammed paper using the procedure given below . While the display alternates between the pap er jam message and HELP START , press the key . An online help message appears. 1 Open the re[...]

Correcting a Paper Jam 4-17 3 Remove the jammed paper . 4 Close the rear cover of the du plexer and the duplex drawer . and remove the paper jam. Close rear cover and duplex drawer. - HELP END -- Press Key ? ?[...]

Correcting a Paper Jam 4-18 Paper J am at the Option Sor ter P aper is jammed at the option sorter . Remove the jammed paper using the procedure given below . While the display alternates between the pap er jam message and HELP START , press the key . An online help message appears. 1 Open the rear cover of the option sorter . 2 Remove the jammed p[...]

Correcting a Paper Jam 4-19 3 Close the rear cover of the option so rter . Close rear cover. - HELP END -- Press Key ? ?[...]

Correcting a Paper Jam 4-20 Jam at th e MP Tr ay P aper is jammed at the MP tray . R emove the jammed paper using the procedure given below . While the display alternates between the pap er jam message and HELP START , press the key . An online help message appears. 1 Remove the paper jammed at the MP tray . 2 Open and close the top c over (the pap[...]

5-1 Chapter 5 F onts 5 This appendix explains the types of fonts you can use with the printer . A font is a set of characters of a particular design . The design is referred to as a typeface . Several characteristics i dentify a fo nt. These incl ude the code se t (F or details on the co de sets, read the Programming Manual on the supplied CD -ROM)[...]

List of Fonts 5-2 List of F onts This section contains a full list of the pri nter’s internal fonts. The printer has 80 PCL fonts, 1 bitmap font, and 80 P ostScript Level 3 compatible fonts. Y ou can print th e font list from the printer by using the pri nter’s operator panel key . T o print a list of fonts, see F ont Lists on page 1- 21 . F on[...]

List of Fonts 5-3 Fon t number Font samples 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67[...]

List of Fonts 5-4 Fon t number Font samples 68 69 70 71 72 73 74 75 76 77 78 79 80[...]

List of Fonts 5-5 KPDL F onts (1)[...]

List of Fonts 5-6 KPDL F onts (2)[...]

A-1 A ppendix A Options A This appendix explains how to expand the pri n ter’s memory and how to install each option unit. Also refer to th e manuals of the resp ective option units. This appendix explains th e following option units: • Expanding the Printer Memory • PF -60 P aper F eeder • DU-61 Duplexer •S O - 6 0 S o r t e r • EF -60[...]

Available Options A-2 Av ailable Options 1 SO-60 Sorter Equipped with five trays each with 200 sheets capacity . P erforms sorting, collating, and mailbox functions . Attaches to the top of the printer . 2 PT -4/PT -60 Rear T ray It attaches to the rear of the printer . 3 Network Interface Card (IB-20/21 E/22) Enables printing from multiple compute[...]

Expandin g the Printer Memor y A-3 Expanding the Printer Memor y This section explains how to exp and the printer’s memory . Expanded printer memory enables you to print more complex pages , download more fonts, and define more macros. This section first explai ns how to re move the main circuit board and then how to install a DIMM (Dual In-l ine[...]

Expanding the Printer Memor y A-4 Remo ving the Main Circuit Boar d The main circuit board of the printe r is equipped with two sockets for memory expan sion. Expan s ion memory is available in the form of DI MM. The following instruct ions are intended f or the technician only . Notes on Handling the Main Circuit Board and DIMM Protect the electro[...]

Expandin g the Printer Memor y A-5 2 Remove the two screws from the printer’s rear panel. 3 Pull the main circu it board al l the way out of the printer . Before pulling the main cir cuit board out, clea r away the area, behind the printer . Foreign object s, accident ally sticking to the back of the main circuit board, can cause serious da mage [...]

Expanding the Printer Memor y A-6 DIMM to be used 32 MB, 64 MB, 128 MB, and 256 MB DIMM can be used for memory expansion. See your K yocera Mita deal er for purchasing information of the DIMM that are best suited for use with this printer . Installing DIMM Insert the DIMM into the socket as shown below . 1 Remove the D IMM from its package. 2 Open [...]

Expandin g the Printer Memor y A-7 Rem ovi n g D IM M T o remove a DIMM, carefully pull th e end clips outwards , then pull the DIMM out of the socket. Return the main circuit board to th e printer by reversing the procedure explained in Removing the Main Circuit Board from the Printer . T esting the E xpansion Memor y After you fin ish installing [...]

Expanding the Printer Memor y A-8 Adjusting the Memor y on the Printer Driv er After you install the additional me mory to the printer , follow the instructions below to set the printer dr iver so that the printer can use the memories efficiently . 1 Click the Windows st art button, and cli ck Printers and Faxes . 2 Right click the Kyocera Mit a FS[...]

Installing Option Units A-9 Installing Option Units PF-60 P aper F eeder Up to three option paper feeders can be installed below the printer . A paper feeder can hold approximately 50 0 sheets of paper at a time. By using option paper feeders in conjunction with the prin ter paper cassette, which can also hold approximatel y 500 sheets of paper , u[...]

Installing Option Unit s A-10 4 Push down the bottom plate until it locks. 5 Set the paper size dial to the size of paper to be used. 6 Adjust the paper guides and paper stopper to the size of paper to be used.  [...]

Installing Option Units A-1 1 7 L oad paper . • Do not load more p aper than will fit under the load limit s on the paper guides. • The p aper cassette will hold appr oximately 500 sheet s of p aper with a 80 g/m² (21 lb) basis weight, or with a th ickness of 0.1 1 mm. 8 Set the stack of paper so that it is under the clips as shown in the figu[...]

Installing Option Unit s A-12 DU-61 Duplex er Install the option duplex er immediately below the printer . By combining the two binding modes (short edge bind and long edge bi nd) with the two printing orientations (portrai t and landscape), duplex prin ting is possible in four different methods. Duplex printing can be specifie d from the applicati[...]

Installing Option Units A-13 4 Gently pla ce the pri nter on t op of the duplexer . 5 Connect the printer cable (parallel int erface cable, USB interface cable, serial interface cable or ne twork interface cable) according to your operation environment. If you are using a paper cassette f or Legal size paper , be sure to pull the cassette out towar[...]

Installing Option Unit s A-14 7 P ass the connected cable and power cord through the opening in the duplexer . 8 Install the duplexer rear cover .[...]

Installing Option Units A-15 SO-60 Sor ter Install the option sorter on top of the pr inter . It is equipped with five sorter trays, with a capacity of 200 sheets each. There are three modes in which printouts can be received : the sorter mode, the collator mode, and the mail box mode (for details about the modes, see KX Printer Drivers Operation G[...]

Installing Option Unit s A-16 5 If the duplexer is installed, remo ve the duplexer rear cover , power cord, and printer cable. 6 Remove the sorter connection cove r from the printer . Store the removed cover in a safe place. 7 Install the sorter by inserting the four hooks on its attachment legs into the notches in the printer . Sorter Connection C[...]

Installing Option Units A-17 8 Push the sorter down. The levers of the attachment legs are in the lock position. 9 Connect the sorter cable to the printer . When removing the sorter , unlock th e attachment legs by releasing the levers a s shown in the figure on e by one, and t hen lift the sort er . Sorter Cable[...]

Installing Option Unit s A-18 10 The sorter is equipped with two po wer cord sockets. The upper one is to be connected to a power outlet an d the lower one is to be co nnected to the printer . If you are using a paper cassette for Le gal size paper , be sure to pull the ca ssette out towards you fi rst before you connect the printer cable. 11 Secur[...]

Installing Option Units A-19 12 If the duplexer is installed, secu re the power cord to the duplexer . T ake care not t o loosen the power cord. 13 If the duplexer is installed, remove the two cut-out portions from the upper part of the duplexer re ar cover removed in step 5. 14 Reinstall the duplexer rear cover . NO Duplexer Rear Cover[...]

Installing Option Unit s A-20 15 Install the five sorter trays to the sorter . 16 Connect the power cord supplied with the printer to the sorter . Do not move or lif t the pri nter with the sorter inst alled. Sorter T ray W arning NO[...]

Installing Option Units A-21 EF-60 En v elope F e eder Install the option envelope feeder at the front of the printe r . By installing the envelope feeder , you can print on a wide variety of di fferent env elope sizes. And the EF -60 feeds envelopes auto matically , making it easy to print on large quantities of envelo pes at one time. Installing [...]

Installing Option Unit s A-22 3 Fit both en ds of the envelop e fe eder into their mountings on the paper transfer unit as shown in the figure and lay the envelope feeder down toward you. 4 Return the paper transfer unit into the printer with the envelope feeder mounted. Load env elopes into the en velope feeder 1 Push the bottom tray downward, as [...]

Installing Option Units A-23 2 Pull out the sub-tray that matc hes the size of the envelopes. 3 L oad env elopes into the envelop e feeder so that they feed in face up, right edge first. Then adjust the en velope feeder’s paper guides to the width of the envelope. • Do not set different types of envelopes into t he feeder at the same time. • [...]

Installing Option Unit s A-24 4 Press the paper setting button. The en velope fee der’s bottom tray is lifted and envelopes that are fed are secured to the envelope feeder . • Paper feed errors may occur whe n using large envelopes. If this happens , remove the envelope s and move the switch to the up ( ) position as shown in the figure. This i[...]

Installing Option Units A-25 PT -4/PT -60 Rear T r ay Use the rear tray when you wish paper to be stacked with the printed side facing up (reverse order), or when you are printing on envelopes, postcards, transparencies, or thick paper . When installing it directly to the printer , use PT -4. If an option duplexer has been installed, use PT -60. 1 [...]

Installing Option Unit s A-26 Network Interface Car d Insert the option network in terface card into the option interface slot at the rear of the printer . The network inte rface card enables the printer to be used in a network. 1 Turn off the printe r and disconnect the power cord and printer cable. 2 Remov e the two screws from the option interfa[...]

Installing Option Units A-27 4 Connect the network cable. 5 Set the network ad dress from the prin ter operator panel (for details about the modes, see Network Interface Parameters on page 1-78 ). Network Cable[...]

Installing Option Unit s A-28 Microdrive (Hard Disk) Insert the Microdrive into its slot on th e main circuit board of the printer . If a Microdrive is installed in the pri nter , received data can be rasterized and stored on this Microdrive. This en ables high-spee d printing of mul tiple copies using an electric sort fu nction. Also, you can use [...]

Installing Option Units A-29 4 Install the Microdriv e into its sl ot on the m ain circuit board. 5 Return the main circuit board to the printer by reversing the procedure followed when removing it. Microdrive Microdrive Slot[...]

Installing Option Unit s A-30 CompactFlash (Memor y) Car d Insert the CompactFlash card into the card slot located near the handle on the right of the printer . A CompactFlash card is a microch ip card that may contain option fonts, macros, forms, et c. The printer reads the contents of the card into its internal memory when printer is turned on. T[...]

B-1 A ppendix B Host Computer Interf ace B This appendix explains the signa ls used in the printer’s parallel and RS-232C interfa ces. It also lists pin assignments, signal functions, timings, connector specifications, and voltage levels. The RS-232C protocols are also covered. Fi nally , it explains how to use the printer in a multi-computer env[...]

Parallel Inte rface B-2 Pa rallel Interface Parallel Interface Communica tion Modes The printer fea tures fast data tra nsmission with th e parallel interface. The parallel i nterface mode can be acti vated from the operator panel. See P arallel Interface Mode on page 1-74 . Use a parallel printer cable that co mplies with the IE EE1284 standard. Y[...]

Parallel Interface B-3 [ ]: Signal names in the Auto mode and Nibble (high) mode (IEEE1284). In the Auto mode and Nibble (high) mode, these signals ar e bi-directional. Pin In/out Description 1 In Strobe* [nStrobe] 2 In/Out Data 0 [Data 1] 3 In/Out Data 1 [Data 2] 4 In/Out Data 2 [Data 3] 5 In/Out Data 3 [Data 4] 6 In/Out Data 4 [Data 5] 7 In/Out D[...]

Parallel Inte rface B-4 Detailed descriptions of the signals follow . Strobe* [nStrobe] (Pin 1) A negative-go ing Strobe* pulse causes the printer to read and latch the data on the Data 0 [1] to Data 7 [8] signal lines. Data 0 [1] to Data 7 [8] (Pins 2 to 9) These eight sign als form th e data byte sent from the host computer to the printer . Data [...]

USB Interface B-5 USB Interface This printer support s the Full-Speed 2.0 USB. USB (Uni versal Serial Bus) interface specifications and interface sign als are as follows. Specifications Basic specification Complies with the Full-Speed USB 2.0. Connector s Printer: B -type receptacle (female) with upstream port Cable: B -type plug (male) Cable Use s[...]

Serial Interface (Option ) B-6 Serial Interface (Option) Installing the option serial interface board kit (IB-11) in the printer enables connection to a computer with an RS-232C standard serial interface. RS-232C Interface Interface Signals The pins of the pr inter’s RS-2 32C in terface connector carry the signals listed in table below . The tabl[...]

RS-232C Protocol B-7 SG - Signal Ground - ( Pin 7) All signals can transmit between the printer and the host computer to send each signal with a signal ground. DTR - Data T erminal Ready - (Pin 20) This output i s used as a buffer near ly-full han dshake line. It is held high (above 3 volts) when the buffer can ac cept more data. RS-232C Interface [...]

RS-232C Protocol B-8 H4: P arity The factory setting is “None” (0 o n the status p rintout). H5: Protocol logic The factory setting is 0. H6: Buffer nearly-full thre shold This is a percentage from 0 to 99. The factory setting is 90 . H7: Buffer nearly-empty threshold This is a percentage from 0 to 99. The factory setting is 70 . The factory se[...]

RS-232C Protocol B-9 PRESCRIBE FRPO D0 Command The PRESCRIBE FRPO D0 command pr ov ides control over XON/XOFF operation when an error occurs on the serial interface. The follow ing table summarizes the error status corresp onding to diffe rent D0 values. Timing of XO N transfer to host while Ready or Waiting Serial interface error Error not handled[...]

RS-232C Cable Conne ction B-10 RS-232C Cable Connection Obtain a Su itab le RS-232C Cable Make sure that the RS-232C cable is wired correctl y . The cable must be a null modem ca ble; that is, one in wh ich pin 2 on either end of the cable is connected to p in 3 on the ot her end. Y o u cannot use a straight cable such as IBM communication adapter [...]

RS-232C Cable Connection B-1 1 Wit h Win d o ws X P , make settings as follows: 1 Click on the St ar t button in the Windows XP task bar and align the cursor with Settings , then click on Control Panel from among the items displayed. 2 The Control Panel window op ens. Double click on System . 3 System Proper ties window opens. Click on the Hardware[...]

RS-232C Cable Conne ction B-12 With W indows 95/98/Me, make settings as foll ows: 1 Click on Star t button i n the Windows 95/98/Me T ask Bar and align the cursor with Settings , then click on Control Panel from among the items displayed. 2 The control panel folder opens. Double click on System . 3 System Properties opens. Click on the Device Manag[...]

RS-232C Cable Connection B-13 In DOS, enter the followi ng commands: C:>MODE COM1:96,N,8,1,P C:>MODE LPT1:=COM1 T o test the interface , enter the fo llowing: CTRL P C:>DIR CTRL P The software settings made using the above procedures are temporary . On most computers, permanent settings must be made with DIP switches.[...]

C-1 A ppendix C Specifica tions C[...]

S pecifications C-2 Specifications Item Description Printing method Electrophotography , la ser scan Printing speed 28 pages/minute (A4 size) when printing multiple copies of the same pa ge Res o lu ti o n F ast 1200 mode wi th KIR [Kyocera Image Refi nement] 600 dpi with KIR (Kyocera Image R efinement) 300 dpi with KIR (Kyocera Image R efinement) [...]

S p ecifications C-3 Ambient conditio ns T emperature: 10 to 32.5 °C (50 to 90.5 °F) Humidity: 20 to 80 % RH Optimum conditions: 23 °C (73.4 °F), 60 % RH Altitude: Max. 2,000 m (6,500 feet) Illumination: Max. 1,500 lux P ower requirements 120 V , 60 Hz, max. 8.0 A (U. S. A./Canada) 220–240 V , 50 Hz/60 Hz, max. 3.9 A (European coun tries) Max[...]

Glossary-1 Glossar y C[...]

Glossary Glossary-2 Cassette mode This is an operation mode for the MP tray . When this mode is used, approximately 100 sheets of plain paper can be fed continuously , the same as for the cassette. dpi (dots per inch) This indicates the numbe r of dots printed per inch, and is the unit of p rinter resolutio n. Ecoprint This is a printing mode that [...]

Glossary Glossary-3 Operator panel This is located on the top of the printer . The panel consists of the mes sage display three indicators and eight keys . The message display shows the printer’s status. Press the keys when you want to sw itch the printer betw een online and offline status, or to cancel printing. Outline font With outline fonts, [...]

Index-1 Inde x[...]

Index-2 A Adhesive label 2-8 Alarm (Buzzer) setting 1- 104 Amorphous silicon drum x Auto continue 1-1 05 C Cassette size 1-24 Charger unit 3-10 Cleaning 3-9 charger wire 3-9 grid cleaner 3-10 paper transfer unit 3-1 3 Cleaning knob 3-9 Code job 1-67 , 1-72 CompactFlash card xii , 1-81 , A-2 , A-30 D Developer unit 4-3 DIMM A-4 Duplexer (DU-61) 4-16[...]

Index-3 preprinte d paper 2-11 recycled paper 2-11 size 2-4 special pape r 2-7 specifications 2- 2 thick paper 2-10 thickne ss 2-5 type 2-7 weight 2-4 Paper cassette 1-3 , A-9 clip A-11 load limit A-11 Paper feeder (PF-60) A-9 Paper guide 1- 25 Paper jam 4-12 Paper size dial 1-24 , 1-25 , A-10 Paper size window 1-24 Paper stopper 1-2 5 , A-10 , A-2[...]

2004.1 ©2003, 2004 is a trademark of Kyocera Corporation[...]