Land Rover Discovery (1997) инструкция обслуживания

[...]

CONTENTS SECTION 1 Introduction .......................................................... 1 SECTION 2 Controls & instruments ........................................ 9 SECTION 3 Driving & operating ............................................. 59 SECTION 4 Owner maintenance ............................................. 97 SECTION 5 General[...]

[...]

1 OWNER’S HANDBOOK This handbook covers the current version of the Land Rover Discovery and, together with the Passport to Service, provides all the information you need to derive maximum pleasure from owning and driving your new vehicle. For your convenience, the handbook is divided into sections, each dealing with a different aspect of driving [...]

2[...]

Introduction 3 PASSPORT TO SERVICE The Passport to Service included in your literature pack, contains important vehicle identification information, details of your entitlement under the terms of the Land Rover warranty, as well as useful consumer advice. Most important of all, however, is the section on maintenance. This outlines the servicing requ[...]

Introduction 4 INFORMATION LABELS FIXED TO THE VEHICLE A. BATTERY WARNING LABEL B. THIS PLUG MUST NOT BE REMOVED WHEN ENGINE IS HOT C. AIR CONDITIONING LABEL D. KEEP CLEAR OF ROTATING PARTS E. JACKING INFORMATION LABEL F. ANTIFREEZE - DO NOT DRAIN G. REWAX AFTER STEAM CLEANING NOTE: Various labels are fixed to the vehicle to draw your attention to [...]

Introduction 5 Details of the vehicle height, both with and without an open sunroof and information on the vehicle’s handling characteristics are printed on the underside of the drivers sun visor. On vehicles fitted with Airbag Supplementary Restraint Systems (SRS), remember to take careful note of warning labels and other information attached to[...]

Introduction 6 VEHICLE IDENTIFICATION NUMBER (VIN) If you need to communicate with a Land Rover dealer, you may be asked to quote the Vehicle Identification Number (VIN). The VIN and other information concerning the vehicle can be found on the certification label affixed to the lock face of the front left-hand door, where shown (this VIN should mat[...]

Introduction 7 ANTI-THEFT PRECAUTIONS While it may be impossible to deter the ’professional’ car thief, the majority of thefts are carried out by unskilled opportunists. Therefore, take vehicle security very seriously and ALWAYS adopt this simple ’five point’ drill whenever you leave your vehicle - even for just a few minutes: • Fully clo[...]

8[...]

9 In this section of the handbook you will find descriptions of the controls and instruments on your Discovery. For your own safety, it is most important to read this section fully and to gain a thorough understanding of all the controls before driving. SECTION 2 Controls & instruments Section Contents Page Controls 11 .........................[...]

10[...]

Controls 11 1. Instrument panel illumination control 2. LH switch panel 3. Driver’s SRS/airbag 4. Instrument and warning light pack 5. Cruise control switches 6. RH switch panel 7. Clock 8. Hazard warning light switch 9. Radio/cassette player 10. Heater and air conditioning controls 11. Coin tray 12. Glovebox 13. Passenger’s SRS/airbag 14. Elec[...]

Locks & alarm 12 ALARM SYSTEM Your vehicle is fitted with a sophisticated electronic anti-theft alarm system. In order to ensure maximum security, you are strongly advised to gain a full understanding of the alarm system by thoroughly reading this section of the handbook. LOCKING THE VEHICLE AND ARMING THE ALARM Before locking the vehicle and a[...]

Locks & alarm 13 Unlocking with the handset Within range of the vehicle, briefly press the PLAIN button on the handset; the hazard warning lights flash once, the alarm is disarmed immediately and the doors unlock. NOTE: The interior lights illuminate when the alarm system is disarmed. If the handset fails to unlock the vehicle, use the key and [...]

Locks & alarm 14 HANDSET BATTERY The handset battery should last for approximately three years, dependent upon use. When the battery needs replacing, it will be apparent from the following symptoms: • The handset will only work every other operation. • The hazard warning lights will not flash on when the alarm is disarmed. Always fit a Pana[...]

Locks & alarm 15 ALARM OR HANDSET DIFFICULTIES Alarm goes off unexpectedly. Ensure all windows, doors, hood and sunroof are closed. Vehicle will not start. Press unlock button on handset. If it still will not start, consult your Land Rover dealer. Hazard lights don’t flash when alarm is armed. Ensure all windows, doors, hood and sunroof are c[...]

Locks & alarm 16 KEY AND HANDSET NUMBERS You have been supplied with two identical remote control handsets and a pair of identical keys which operate all locks, including the rear door and petrol flap. The key number is stamped on a tag attached to the key ring. Check that the key number has been entered in the space provided on your Security I[...]

Locks & alarm 17 Child locks Move the locking levers to the ’ON’ position (as illustrations) to engage. With the child locks engaged, neither the rear doors nor the tailgate can be opened from inside the vehicle, thereby avoiding the risk of a door being opened accidentally while the vehicle is moving. WARNING NEVER leave unsupervised child[...]

Seats 18 MANUALLY OPERATED FRONT SEATS Forward/backward movement Lift the bar to slide the seat forward or back. Ensure the seat is locked in position before driving. WARNING To avoid the risk of loss of control and personal injury, DO NOT adjust the driver’s seat while the vehicle is in motion. Lumbar support (1) Rotate the handwheel to increase[...]

Seats 19 POWER OPERATED FRONT SEATS (if fitted) The seat adjustment controls are situated on the centre console adjacent to the seat bolsters. Adjustment is only possible when the starter switch is turned to positions ’I’ or ’II’, or with a front door open when the starter switch is in position ’0’. The following functions are available[...]

Seats 20 Seat cushion height Push the switch up or down, to raise or lower the cushion. Lumbar support adjustment Rotate the handwheel to increase or decrease support to the lumbar region of the back. Seat back adjustment Twist the switch forward or backward until the desired seat back angle is achieved.[...]

Seats 21 Head restraint adjustment (power operated seats only) WARNING Head restraints are designed to support the back of the head (NOT THE NECK), and to restrain rearward movement of the head in the event of a collision. The restraint must be positioned level with the head to be effective. DO NOT drive, or carry passengers, with the head restrain[...]

Seats 22 FOLDING THE REAR SEATS Before folding the rear seats, pass the seat belt locks through the junction of the backrest and the cushion and into the loadspace. WARNING DO NOT adjust the seats while the vehicle is in motion. Ensure your fingers are clear of the seat latches when folding the rear seats. When returning the seat to its upright pos[...]

Seats 23 INWARD FACING SEATS (if fitted) With the loadspace cover (if fitted) retracted and stowed, pull out the seat stand, and fold down the seatbase. Please refer to Infant and child restraint section for correct placement of the child seat. WARNING DO NOT attempt to fit an infant or child restraint system to the inward facing seats. Ensure that[...]

Seat belts 24 SEAT BELT SAFETY WARNING Seat belts are life saving equipment. In a collision, occupants not wearing a seat belt will be thrown around inside, or possibly thrown out of the vehicle. This is likely to result in more serious injuries than would have been the case had a seat belt been worn. It may even result in loss of life! Don’t tak[...]

Seat belts 25 WEARING SEAT BELTS CORRECTLY Fastening the inertia reel belts Draw the belt over the shoulder and across the chest, and then insert the metal tongue plate into the lock nearest the wearer - a ’CLICK’ indicates that the belt is securely locked. In some circumstances, perhaps due to the vehicle being parked on a slope, the inertia m[...]

Seat belts 26 Lap belts The rear central and inward facing seating positions are fitted with lap belts only. To adjust, pull the slider along the belt and feed the webbing through the buckle until the belt is comfortably tight. Fit the belt as low as possible on the hips (never on the abdomen). WARNING Seat belts are designed to bear upon the bony [...]

Seat belts 27 CHILD RESTRAINTS FOR SMALL CHILDREN AND BABIES Infants and children too small for adult seat belts should be restrained in a child safety seat or restraint system appropriate to their age and/or size, and which is approved for use in your vehicle. Always ensure that the manufacturer’s fitting instructions are followed exactly. Seat [...]

Seat belts 28 Care & maintenance of seat belts WARNING • DO NOT allow foreign matter (particularly sugary food and drink particles) to enter the seat belt locks - such substances can render the locks inoperative. • Regularly inspect the belt webbing for signs of fraying, cuts and wear, also paying particular attention to the condition of th[...]

SRS/Airbag 29 The airbag supplementary restraint system (SRS) provides additional protection for the driver and front seat passenger, in the event of a collision or severe frontal impact on the vehicle. Always remember; the SRS/airbags are a supplementary restraint system providing ADDITIONAL protection in certain types of frontal impact collisions[...]

SRS/Airbag 30 WARNING Following inflation, some SRS/airbag components are hot - DO NOT touch until they have cooled. Even with SRS/airbag equipment fitted, seat belts must ALWAYS be worn because: • An airbag will only provide additional protection in certain types of frontal collisions. NO protection is afforded against the effects of side or rea[...]

SRS/Airbag 31 SRS/airbag warning light Whenever the starter switch is turned to position ’II’, the diagnostic control unit monitors the readiness of the system’s electrical circuits. The elements of the system being monitored include: • SRS warning light • Rotary coupler • Airbag modules • Airbag diagnostic control unit • Airbag wir[...]

SRS/Airbag 32 WARNING The components that make up the SRS/airbag are sensitive to electrical or physical interference, either of which could easily damage the system and cause inadvertent operation or a malfunction of the airbag module. ALWAYS seek the assistance of a Land Rover dealer to carry out any of the following: • Removal or repair of any[...]

Steering column 33 STEERING COLUMN ADJUSTMENT Adjust the height of the steering column to suit your driving position, as follows: 1. Push the locking lever up (and hold in position). 2. Move the steering wheel up or down into the desired position. 3. Release the locking lever. WARNING DO NOT adjust the height of the steering wheel while the vehicle[...]

Exterior mirrors 34 ELECTRIC MIRRORS 1. Turn the control fully to ’L’ or ’R’ to select either the left or right hand mirror. 2. With the starter switch turned to position ’II’, press the top/bottom/left or right of the control to move the mirror glass to the required position. 3. When adjustment is complete, return the control to the po[...]

Instruments 35 1. Tachometer Indicates engine speed in revolutions per minute. In normal driving conditions the engine is most fuel efficient between 2000 and 3000 rev/min. The vehicle is fitted with a system which automatically restricts the number of engine revolutions per minute once the engine’s maximum ’governed’ speed has been reached. [...]

Instruments 36 6. Temperature gauge Once the engine coolant has reached its normal operating temperature, the pointer should remain between the ’C’ (cold) and ’H’ (hot) segments. If the pointer enters the HOT segment, stop the vehicle as soon as safety permits and seek qualified assistance before continuing. 7. Fuel gauge The pointer indica[...]

Warning lights 37 The warning lights are colour coded as follows: WARNING DO NOT drive if a RED warning light remains on or illuminates whilst the engine is running. RED lights are warnings. AMBER lights are cautions. GREEN & BLUE lights indicate that a unit is operating. Seat belt - RED If the driver’s seat is occupied the light illuminates [...]

Warning lights 38 Hazard warning lights - RED Illuminates when the hazard warning lights are flashing. Low oil pressure - RED The light should extinguish when the engine is started. If the light remains on or illuminates whilst driving, STOP THE VEHICLE IMMEDIATELY and seek qualified assistance. Always check oil levels when this light illuminates. [...]

Warning lights 39 Battery charging - RED The light illuminates as a bulb check when the starter switch is turned to position ’II’ and extinguishes when the engine is running. If it remains on, or illuminates whilst driving, a fault is indicated. Seek qualified assistance urgently. Check engine - AMBER The engine management system on your Land R[...]

Lights & indicators 40 Direction indicators Move the lever down to indicate a LEFT turn, and up to indicate a RIGHT turn (the GREEN warning light on the instrument panel will flash in time with the direction indicators). Hold the lever part-way up or down against spring pressure to indicate a lane change. Side, tail and instrument panel lights [...]

Wipers & washers 41 WINDSCREEN WIPERS The wipers and washers will only operate when the starter switch is turned to position ’II’. • Single wipe Pull the lever down and release immediately. NOTE: With the lever held down, the wipers will continue operating at high speed until it is released. • Intermittent wipe Turn switch to first posi[...]

Wipers & washers 42 Rear window wiper Press to operate: after continuously wiping 3 or 4 times, the wiper operates intermittently (approx once every 6 seconds) until switched off. Rear window wash/wipe Press and hold switch for the required duration of window washing. The wiper operates automatically during washing and continues for a further 3[...]

Switches 43 Heated rear window Press to operate; press a second time to switch off. The indicator light in the switch illuminates while the heating elements are switched on and extinguishes when they are turned off. Note that the heated rear window operates only with the engine running. After 15 minutes continuous operation, the heater switches off[...]

Switches 44 Hazard warning lights Press to operate; all the direction indicator lights (including those fitted to a trailer) will flash in conjunction with each other. Use ONLY in an emergency to warn other road users when your stationary vehicle is causing an obstruction, or is in a hazardous situation. Remember to switch off before moving away. F[...]

Windows 45 ELECTRIC WINDOWS The switches on the centre console operate as follows: 1. Right hand front window. 2. Left hand front window. 3. Right hand rear window. 4. Isolation switch for rear door window switches. 5. Left hand rear window. NOTE: Rear windows can also be operated by individual window switches mounted on each rear door, provided th[...]

Sunroof 46 ELECTRIC SUNROOFS (if fitted) An electric sunroof can be operated when the starter switch is at position ’II’, and for up to 45 seconds after the starter switch is turned off (provided no door is opened in the meantime). The roofs open and close in two separate phases as follows: To TILT the roof: BRIEFLY press the upper portion of t[...]

Heating & ventilation 47 The location of air vents is shown by the air-flow arrows in the picture. The temperature of air supplied to each vent is controlled by the heater. NOTE: Vent (1) is designed to keep the audio unit cool. There is no air flow from this vent. Face level vents Each vent can be opened or closed by rotating the thumbwheel: l[...]

Heating & ventilation 48 HEATER CONTROLS 1. Temperature controls The left hand control varies air temperature from the vents on the left side of the vehicle. The right hand control adjusts air temperature from the vents on the right side. Rotate each control clockwise (towards the RED segment) to increase the air temperature, or counter-clockwi[...]

Heating & ventilation 49 4. Air recirculation control Press to recirculate air inside the vehicle (indicator light illuminates). The air recirculation mode prevents the heating system from taking in fresh air from outside the vehicle. Instead, the air already inside the vehicle is recirculated, thus preventing the entry of traffic fumes. In col[...]

Heating & ventilation 50 USING YOUR HEATER Fresh air enters the heater unit through the grille in front of the windscreen and stale air is drawn out through vents in the rear of the vehicle. Ensure the grille is kept clear of obstructions (especially snow and ice). Ducts along the transmission tunnel provide heating for rear seat passengers - t[...]

Air conditioning 51 AIR CONDITIONING The air conditioning system provides additional cooling to the vehicle interior, and also reduces the moisture content of the air. Using the air conditioning The air conditioning system will only operate when the air blower is switched on, and should only be used when the engine is running. It is also important [...]

Air conditioning 52 The following examples are included for your guidance: Normal cooling After starting the engine, switch on the air conditioning and set the heating and ventilation controls as shown. The blower speed can be varied to suit your comfort requirements. Maximum cooling Start the engine and switch on the air conditioning. Set the blow[...]

Interior equipment 53 FRONT INTERIOR LIGHT With the switch midway between the ’ON’ and ’OFF’ positions, the light will illuminate automatically whenever a door is opened. Automatic operation The front and rear interior lights illuminate automatically whenever a door is opened, and remain illuminated for approximately 15 seconds after ALL th[...]

Interior equipment 54 CIGAR LIGHTER With the starter switch turned on, press the centre of the lighter in to heat up. When it has reached the correct temperature it will partially eject and can then be withdrawn for use. • ONLY hold the cigar lighter by the handle. FRONT ASHTRAY Push the front of the ashtray to open. To remove the interior compar[...]

Interior equipment 55 CD AUTOCHANGER (if fitted) The CD autochanger is located under the left, front seat, behind a removable panel. To gain access to the autochanger, depress the catch (arrowed in illustration) and remove the panel. To remove the magazine Slide the autochanger cover (1) FULLY open and press button (2) to eject the magazine. Keep t[...]

Interior equipment 56 CUP HOLDER Push leading edge of tray to open. ILLUMINATED VANITY MIRRORS With the starter switch in position ’I’ or ’II’, open the mirror cover to illuminate. Close the cover to extinguish the lights. INTERIOR REAR-VIEW MIRROR The interior mirror is equipped with an automatic dimming function, which operates when the c[...]

Loadspace cover 57 LOADSPACE COVER The rear loadspace cover is a spring loaded roller blind, which can be retracted when not in use. Lift the cover over the hooks (1) and allow it to retract. Secure the cover in its retracted position with the retaining strap (2), attached to the rear seat back. To remove the loadspace cover: 1. Slide the plastic s[...]

Rear step 58 REAR STEP (if fitted) Press down to lower the step. The step will automatically return to its stowed position when not in use.[...]

59 SECTION 3 Driving & operating Section Contents Page Starter switch & steering lock 61 .................... Starting & driving 63 ...................................... Catalytic converter 66 ..................................... Fuel 68 ............................................................ Manual transmission 72 ..............[...]

60[...]

Starter switch & steering lock 61 STEERING LOCK To unlock the steering Insert the key FULLY and turn the starter switch to position ’I’ while turning the steering wheel slightly. The turning movement is necessary to disengage the lock. To lock the steering Turn the key to position ’0’ and withdraw it from the starter switch. Then turn t[...]

Starter switch & steering lock 62 WARNING To prevent the steering column lock engaging it is most important that before the vehicle is moved in any way, the key be inserted in the lock and turned to position ’I’. If, due to an accident or electrical fault, it is not considered safe to turn the key, disconnect the negative lead of the batter[...]

Starting & driving 63 STARTING WARNING The catalytic converter is easily damaged by improper use, particularly if the wrong fuel is used, or if an engine misfire occurs. Before starting the engine and driving, ENSURE that you are familiar with the precautions shown under ’Catalytic Converter’ later in this section. In particular, you should[...]

Starting & driving 64 Automatic gearbox models WARNING When the engine has started, BEFORE moving the gear selector lever out of ’P’ or ’N’ it is important that the parking brake or foot brake is firmly applied and the accelerator pedal is not depressed - otherwise, the vehicle may move immediately if the gear selector lever is moved to[...]

Starting & driving 65 VEHICLE HEIGHT WARNING The overall height of your vehicle exceeds that of ordinary passenger cars (the height is shown on the underside of the sun visor). Always be aware of the height of your vehicle and check the available clearance before driving through low entrances. This is particularly important if the vehicle is fi[...]

Catalytic converter 66 CATALYTIC CONVERTER The exhaust system incorporates a catalytic converter, which reduces emissions from the engine into environmentally less harmful gases. The catalytic converter can be easily damaged through improper use, particularly if the wrong fuel is used, or if an engine misfire occurs. For this reason it is VERY IMPO[...]

Catalytic converter 67 Driving • Provided the engine has reached its normal operating temperature, if a misfire is suspected or the vehicle lacks power while driving, it may be driven SLOWLY (at risk of damaging the catalyst) to a Land Rover dealer for assistance. • NEVER allow the vehicle to run out of fuel (the resultant misfire could destroy[...]

Fuel 68 USE ONLY UNLEADED FUEL Octane requirements Always use PREMIUM UNLEADED GASOLINE with a CLC or AKI octane rating of 90 or 92 (95 or 96 RON). NOTE: Federal law requires that gasoline octane ratings be posted on the pumps. The Cost of Living Council (CLC) octane rating or Anti Knock Index (AKI) octane rating shown is an average of Research Oct[...]

Fuel 69 Gasoline/oxygenated fuel blends To avoid invalidating the vehicle warranty, use ONLY fuels blended within the following limits. 1. Up to 15% of Methyl Tertiary Butyl Ether (MTBE) and unleaded fuel mix. 2. Up to 15% of Ethyl Tertiary Butyl Ether (ETBE) and unleaded fuel mix. 3. Up to 10% of Ethanol (Ethyl or grain alcohol) and unleaded fuel [...]

Fuel 70 Fuel filling Filling station pumps are equipped with automatic cut-off sensing to avoid fuel spillage - only fill the tank until the filler nozzle automatically cuts off the supply. DO NOT attempt to fill the tank beyond this point or spillage could result due to expansion of the fuel. The reduced diameter filler neck, accepts ONLY a narrow[...]

Fuel 71 FUEL CUT-OFF SWITCH The fuel cut-off switch is a safety device which, in the event of a collision or sudden impact, automatically cuts off the fuel supply to the engine. The switch is located in the engine compartment on the bulkhead. After an impact, the switch must be reset by pressing the rubber top (arrowed in illustration) before the e[...]

Manual transmission 72 MANUAL TRANSMISSION Manual transmission vehicles feature a five speed main gearbox and a two speed transfer box. In addition, a centre differential in the transfer box distributes the drive to the front and rear axles, providing permanent four wheel drive. By using the main gearbox in conjunction with the transfer gearing ten[...]

Automatic transmission 73 AUTOMATIC TRANSMISSION The automatic transmission features a four speed main gearbox with a torque converter and a two speed transfer box. A centre differential in the transfer box distributes power to both front and rear axles, providing permanent four wheel drive. Using the main gearbox in conjunction with the transfer g[...]

Automatic transmission 74 Automatic selector lever positions ’P’ (Park) In this position the transmission is locked to prevent the vehicle from rolling away. Select ONLY with the vehicle stationary and the parking brake on. ’R’ (Reverse) Select ONLY when the vehicle is stationary. ’N’ (Neutral) Use this position when the vehicle is stat[...]

Automatic transmission 75 Gear change speeds With ’D’ selected, the road speed at which gear changes take place will vary according to the position of the accelerator: minimum acceleration will result in low road speed gear changes, while larger throttle openings will cause the main gearbox to delay gear changes until faster road speeds have be[...]

Transfer gearbox 76 TRANSFER GEARBOX The two speed transfer gearbox, is used to select either the high or low range of gears and, in addition, also controls the centre differential (known as the ’DIFF LOCK’). A shift interlock safety feature is fitted which prevents any transfer box gear selection being made unless the ignition is switched on a[...]

Transfer gearbox 77 USING THE TRANSFER GEARBOX There are two ways of operating the transfer gearbox lever; the ’normal’ method - recommended for inexperienced drivers - and the ’advanced’ method for experienced drivers. Normal method Manual models: With the vehicle stationary and the engine running, depress the clutch and then move the tran[...]

Transfer gearbox 78 Automatic models: Changing from ’H’ (high) to ’L’ (low) or vice versa without stopping the vehicle can be achieved as follows: Reduce (or increase) the speed of the vehicle to 5 mph (8 km/h) and release the accelerator. Select ’N’ with the main gear selector and move the transfer lever quickly to the required ’H’[...]

Transfer gearbox 79 Selecting diff lock The diff lock can be engaged or disengaged either with the vehicle stationary, or when driving at any road speed, and without depressing the clutch. However, with the vehicle in motion it is ESSENTIAL to be travelling on firm ground, in a straight line, and without wheel slip. WARNING DO NOT engage the diff l[...]

Transfer gearbox 80 Diff lock warning light The amber warning light on the instrument panel illuminates when the diff lock is actually engaged - rather than when it has been selected. Similarly it will only extinguish when the diff lock is actually disengaged. This accounts for a slight delay between diff lock deselection and the warning light exti[...]

Braking systems 81 FOOT BRAKE As a safety precaution, the hydraulic braking system operates through dual circuits. If one circuit fails, the other will continue to function, but increased brake pedal travel, greater pedal effort and longer stopping distances will be experienced. Power assistance The braking system is power assisted, but ONLY when t[...]

Braking systems 82 Wet conditions WARNING Driving through water or even very heavy rain may adversely affect braking efficiency. Always dry the braking surfaces by intermittent light application of the brakes, first ensuring that you are at a safe distance from other road users. Parking brake Unlike most other vehicles, the parking brake on your La[...]

Braking systems 83 ANTI-LOCK BRAKES WARNING ABS cannot overcome the physical limitations of stopping in too short a distance, cornering at high speed, or the danger of aquaplaning i.e. where a layer of water prevents adequate contact between the tyres and road surface. DO NOT pump the brake pedal at any time; this will interrupt operation of the sy[...]

Braking systems 84 Additional operating information While anti-lock braking is designed to operate equally effectively in ’off-road’ driving conditions, on certain surfaces total reliance on the system may be unwise - remember, in normal circumstances, anti-lock braking operates only AFTER the driver has already lost control. Anti-lock braking [...]

Braking systems 85 Warning light The anti-lock braking system warning light illuminates when the starter switch is turned to position ’II’, and performs an ABS system check. If no faults are found, the light briefly extinguishes before illuminating again and remaining on until the engine has started and the vehicle reaches speeds in excess of 5[...]

Cruise control 86 WARNING DO NOT use cruise control when using low range transfer gears or reverse gears. DO NOT use cruise control on winding or slippery road surfaces, or in traffic conditions where a constant speed cannot easily be maintained. DO NOT rest your foot under the accelerator pedal while cruise control is engaged - your foot could be [...]

Cruise control 87 To reduce the cruising speed Press the ’RES -’ switch or use the brake pedal to slow the vehicle until the required speed has been reached, then press the ’SET +’ switch to establish the new cruising speed (remember that cruise control will not operate at speeds below 28 mph (45 km/h). To increase the cruising speed Press [...]

Towing & load carrying 88 TOWING The torque ranges of Land Rover engines allow maximum weight loads to be pulled smoothly from standstill, and reduce gear changing on hills or rough terrain. The suspension is designed to cope with a heavy trailer load without upsetting the balance or feel of the vehicle. Towing weights are listed in ’General [...]

Towing & load carrying 89 When preparing your vehicle for towing, pay careful attention to the trailer manufacturer’s recommendations and also follow the guidelines below: • Ensure that the towing vehicle tyre pressures are correct and that the trailer tyre pressures are as recommended by the trailer manufacturer. • With the trailer and v[...]

Towing & load carrying 90 Automatic gearbox models To avoid overheating the main gearbox, it is not advisable to tow heavy trailer loads at speeds of less than 20 mph (32 km/h) using the main gearbox in high range. Use the transfer gearbox to select LOW range instead. NOTE: Above 1,000 feet (300 metres) the effects of altitude can adversely aff[...]

Towing & load carrying 91 ROOF RACK The roof rack has two side rails permanently fixed to the roof of the vehicle and three removable cross rails which are stowed in the tool bag beneath the rear seat. Each cross rail has a pair of locating pins at each end. With the grooved side upwards, fit the cross rails to one side rail by inserting the fi[...]

Emergency starting 92 Starting an engine with a discharged battery The ONLY recommended methods of restarting a vehicle with a discharged battery are: • The use of a substitute battery fitted to the disabled vehicle. • The use of booster cables, to connect the battery from a donor vehicle to the discharged battery. WARNING A vehicle with automa[...]

Emergency starting 93 Always adopt the following procedure when using booster cables: 1. If a donor vehicle is to be used, both vehicles should be parked with their battery locations adjacent to each other. Ensure that the two vehicles do not touch. 2. Apply the parking brakes and ensure that the transmission of both vehicles is set in neutral (’[...]

Vehicle recovery 94 TOWING FOR RECOVERY If your vehicle is to be recovered by towing, the best method is via a flatbed tow truck. However, if it is necessary for the vehicle to be towed with all four wheels on the ground, always adhere to the following procedure: 1. With the parking brake applied, set the main gearbox and transfer box in neutral. S[...]

Vehicle recovery 95 Towing eyes The towing eyes at the front and rear of the vehicle are designed for vehicle recovery purposes only and must NOT be used to tow a trailer or caravan. FRONT: A single towing eye, protruding through the spoiler (see illustration), is provided at the front of the vehicle. DO NOT use the front lashing rings for towing p[...]

96[...]

97 The long-term safety, reliability and performance of your vehicle will depend very largely on how well it is maintained. Maintenance is the owner’s responsibility, and it is ESSENTIAL that all routine services are carried out by a Land Rover dealer at the specified intervals. These are shown in the Passport to Service book included in the lite[...]

98[...]

Owner maintenance 99 OWNER MAINTENANCE In addition to the routine services, which should be carried out by your Land Rover dealer at the intervals shown in the Passport to Service, a number of simple checks and adjustments (listed below) must be carried out by the owner or driver on a regular basis. These are fully described on the pages that follo[...]

Owner maintenance 100 Planned maintenance Regular systematic maintenance is the key to ensuring the continued reliability and efficiency of your Discovery. The routine maintenance requirements for your vehicle are shown in the Passport to Service. Most of the necessary workshop maintenance requires specialised knowledge and equipment and should pre[...]

Owner maintenance 101 SAFETY IN THE GARAGE Whenever you carry out maintenance on your vehicle, the following safety precautions should be followed at all times. • ALWAYS keep hands, hair, tools and items of clothing clear of all drive belts and pulleys. • DO NOT touch exhaust or cooling system components until they are cool. • DO NOT touch el[...]

Hood opening 102 WARNING Ensure the wipers are switched off and have returned to the parked position before opening the hood. Pull the hood release handle. Push the safety catch to the right and raise the hood. Release the support stay from the underside of the hood and fit the stay in the slotted hole in the locking platform. Closing the hood Afte[...]

Engine compartment 103 1. Fusebox - engine compartment. 2. Cooling system reservoir. 3. Brake fluid reservoir. 4. Clutch fluid reservoir. 5. Automatic gearbox fluid level dipstick (if fitted). 6. Washer reservoir. 7. Engine oil dipstick. 8. Engine oil filler cap. 9. Power steering reservoir. Instructions on how and when Owner maintenance should be [...]

Engine compartment 104 ENGINE OIL LEVEL-CHECK & TOP-UP Check the oil level every 250 miles (400 km), when the engine is HOT and with the vehicle resting on level ground. Switch off the engine and let the vehicle stand for five minutes to allow the oil to drain back into the sump. Withdraw the dipstick and wipe the blade clean and then fully rei[...]

Engine compartment 105 AUTOMATIC GEARBOX FLUID LEVEL CHECK & TOP-UP The automatic gearbox fluid must ONLY be checked when the engine and gearbox are COLD (see ’Note’ below). Ensure the vehicle is resting on level ground, then select ’P’ (park) and start the engine. With the engine running at idle speed and both foot brake and parking br[...]

Engine compartment 106 COOLING SYSTEM TOP-UP WARNING NEVER remove the filler cap when the engine is hot - escaping steam or scalding water could cause serious personal injury. The coolant level in the expansion tank should be checked at least weekly (more frequently in high mileage or arduous operating conditions). Always check the level WHEN THE S[...]

Engine compartment 107 WINDSCREEN WASHER TOP-UP The windscreen washer reservoir also supplies the rear screen and headlight washer jets (where fitted). Check the reservoir level and top-up with a mixture of water and an approved screen washer solvent to approximately 1 inch (25 mm) below the bottom of the filler neck. In cold weather, to prevent fr[...]

Engine compartment 108 BRAKE FLUID CHECK WARNING Contact your dealer immediately, if brake pedal travel is unusually long, or if there is any appreciable drop in brake fluid level. DO NOT drive the vehicle with fluid level below the ’MIN’ mark. Brake fluid will damage painted surfaces, soak up any spillage with an absorbant cloth immediately an[...]

Engine compartment 109 POWER STEERING TOP-UP ONLY check the fluid level when the engine is cold and switched off, and ensure that the steering wheel is not turned after stopping the engine. Wipe the filler cap clean to prevent dirt from entering the reservoir. Remove the filler cap and wipe the dipstick clean using a lint free cloth. Refit the cap [...]

Tyres 110 WARNING Never drive your vehicle if the tyres are badly worn, cut or damaged, or if the pressures are incorrect. Incorrectly inflated tyres wear rapidly and seriously affect the vehicle’s safety and road handling characteristics. Caring for your tyres Always drive with consideration for the condition of the tyres and frequently inspect [...]

Tyres 111 Replacement tyres Wheel rims and tyres are matched to suit the handling characteristics of the vehicle. For safety, ALWAYS check that replacement tyres comply with the manufacturer’s original specification and that the load rating shown on the side wall is the same as that of the original equipment. Contact your Land Rover dealer for fu[...]

Washer jets & wiper blades 112 WIPER BLADE REPLACEMENT To renew a front or rear wiper blade, lift the wiper arm away from the windscreen, press the retaining clip (1) and slide the wiper blade down the arm to remove. Locate the new blade assembly on the arm and push into engagement until the blade is retained by the clip. Always fit replacement[...]

Battery 113 WARNING Batteries contain sulphuric acid. If the acid comes in contact with the eyes or skin, wash immediately with copious quantities of cold water and seek medical advice. During normal operation batteries emit explosive hydrogen gas - ensure sparks, flames and other ignition sources (including cigars and cigarettes) are kept away fro[...]

Battery 114 WARNING ONLY fit a replacement battery of the same type and specification as the original. Other batteries may vary in size and have different terminal positions, capable of creating a potential fire hazard if the terminals or leads were to come into contact with the battery clamp assembly. DO NOT let the engine run without the battery [...]

Wheel changing 115 IMPORTANT INFORMATION Before jacking the vehicle always observe the following precautions! • Park your vehicle away from the highway, and make your passengers wait in a safe area AWAY from the vehicle. • Switch on the hazard warning lights to alert other road users. • Ensure the jack is positioned on firm, level ground. •[...]

Wheel changing 116 The jack and wheel chock are stowed in the front of the engine compartment. The jack handle and tools are stowed in a tool bag under the rear seat. WARNING Tools stowed in the engine compartment will be hot if the engine has been running. DO NOT use the spare wheel securing nuts in place of the road wheel nuts. The wheels are ext[...]

Wheel changing 117 Operating the jack Slot the jack lever together, ensuring that the spring clip protrudes from the engagement slot where the two parts join (see inset). Close the jack release valve by turning it fully clockwise and then insert the lever into the socket where shown. Pump the lever up and down to raise the jack. To lower the jack, [...]

Wheel changing 118 Positioning the jack Always position the jack from the front or rear of the vehicle directly in line with the jacking points. WARNING NEVER use the jack from the side of the vehicle. ALWAYS use the complete, two piece, jack lever throughout to minimise any chance of accidental contact with a hot exhaust system. ONLY jack the vehi[...]

Wheel changing 119 Changing a wheel Before raising the vehicle, ensure that all the precautions listed at the beginning of this section have been observed and, in particular, that the wheel chock is correctly positioned and that the differential lock is engaged. • Use the wheel nut wrench to slacken the wheel nuts half a turn anti-clockwise. • [...]

Fuses 120 Fuses are simple devices which protect electrical equipment against the effects of excess current. Renewing a fuse Always turn the starter switch to position ’O’ and switch off the affected electrical circuit before removing a fuse. Press the fuse removal tweezers onto the head of a fuse and pull. Always replace a fuse with another of[...]

Fuses 121 Fuse No. Rating Electrical circuit (amps) 1 15 Stop lights, direction indicators 2 10 LH side lights 3 10 Radio/cassette/CD player 4 10 RH headlight main beam 5 10 LH headlight main beam 6 20 Cigar lighter, vanity mirror, heated seats 7 10 SRS/airbag 8 10 RH side lights 9 10 Rear fog guard lights 10 10 LH headlight dipped beam 11 10 RH he[...]

Fuses 122 ENGINE COMPARTMENT FUSE BOX WARNING Batteries emit explosive hydrogen gas; ensure that sparks, flames and other ignition sources (i.e. cigarettes) are kept away from the engine compartment. A second fuse box is located on the right side of the engine compartment adjacent to the engine coolant reservoir. The circuits protected and their lo[...]

Bulb replacement 123 REPLACEMENT BULBS Watts Headlight 60/55 Front side light 5 Direction indicator light 21 Front fog light Tail light 5 Stop light 21 Rear fog guard light 21 Reversing light 21 High mounted stop light 21 Side repeater light 5 Number plate light 5 Interior light (front) 10 Interior light (rear) 5 Loadspace light 10 Vanity mirror li[...]

Bulb replacement 124 HEADLIGHT AND SIDELIGHT Light unit removal To replace either headlight or sidelight, remove the light unit as follows: Disengage the three retaining clips and rotate them approximately 10 degrees (see inset) to align with the slots. The light unit can now be released forward. Headlight bulb Disconnect the electrical multi-plug [...]

Bulb replacement 125 Replacing the headlight unit Replacement is a reversal of the removal procedure. Sidelight bulb: With the light unit removed (see previous page), disconnect the electrical multi plug and disengage the bulb holder, by twisting a quarter turn anti-clockwise. Withdraw the bulb holder to replace the bulb.[...]

Bulb replacement 126 FRONT DIRECTION INDICATORS Unclip the spring to release the light unit. Lift out the light unit and turn the bulb holder anti-clockwise to release. Push and twist the bulb to remove. When replacing the light unit, locate the two lugs at the bottom of the unit before re-engaging the spring. SIDE REPEATER LIGHT Push the lens firm[...]

Bulb replacement 127 REAR LIGHT CLUSTER (Stop/tail, reverse, direction indicator & fog guard lights) To gain access to the light cluster, either: remove the side pocket cover (picture ’A’) or, half pull out the inward facing seat (picture ’B’), as applicable. Use a small screwdriver to lever the fastener cover free (the fastener is loca[...]

Bulb replacement 128 REAR LIGHT CLUSTER (Stop/tail, reverse, direction indicator & fog guard lights) Vehicles fitted with rear air conditioning: To gain access to the rear of the left hand light unit, remove the access panel by using a small coin to twist the two turn-buckles 90˚ anti-clockwise, then pull the panel away. By feel, locate the da[...]

Bulb replacement 129 BUMPER MOUNTED LIGHTS (Tail lights & direction indicators) Reach behind the bumper and twist to remove the relevant bulb holder, push and twist to release the bulb. NUMBER PLATE LIGHTS Remove the screws and withdraw the lens. Pull the bulb out. HIGH MOUNTED STOP LIGHT Remove the screws from the cover and twist to remove the[...]

Bulb replacement 130 INTERIOR LIGHT Pry the lens from the unit. Spread the bulb holders to release the bulb. GLOVEBOX LIGHT Slide the light unit to the left and insert a broad flat-headed screwdriver to release the retaining catch. Withdraw the light unit from the glovebox and pull out bulb to replace. LOADSPACE LIGHT Pry the light from its locatio[...]

Cleaning & vehicle care 131 WASHING YOUR VEHICLE WARNING Some high pressure cleaning systems, are sufficiently powerful to penetrate door and window seals and damage rubbing strips and locking mechanisms. Never aim the water jet directly at heater air intakes, body and sunroof seals, or at any components that might easily be damaged. Wash your [...]

Cleaning & vehicle care 132 Body protection After washing, inspect the paintwork for damage. Any stone chips, fractures or deep scratches in the bodywork should be repaired promptly. Bare metal will corrode quickly and can develop into major repair expense. Some exterior panels of your vehicle are of aluminum which will not corrode in the same [...]

Cleaning & vehicle care 133 LOOKING AFTER THE INTERIOR Clean plastic-faced, or cloth covered surfaces with diluted upholstery cleaner. Leather seats, steering wheel and trim features should be cleaned with a damp cloth, moistened with undiluted leather upholstery cleaner. Leave for five minutes, and then repeat the operation using a clean cloth[...]

Air cleaner 134 Renewing the air cleaner element at the recommended service intervals (see your ’Passport to Service’), is extremely important. However, to maintain optimum engine performance under dusty operating conditions, more frequent renewal will be necessary. Consult your dealer for guidance. Air cleaner element renewal Release the two c[...]

Spark plugs 135 Spark plug removal Remove the plug leads (1), ensuring that you hold the rubber shroud and NOT the H.T. leads (this will ensure no damage occuring to the connectors during removal). Ensure that the recesses around the plugs are free from debris (to avoid foreign matter accidentally entering the cylinder head) and use a suitable spar[...]

Engine oil & filter 136 Ensure the engine oil is changed at the recommended service intervals (see your ’Passport to Service’). Under severe operating conditions (i.e. regular use in muddy terrain or dusty conditions), the engine oil must be changed frequently, even to the extent of a daily change. Consult your Land Rover dealer for guidanc[...]

Engine oil & filter 137 Engine oil filter renewal To avoid draining the oil pump, it is essential that the engine is filled with oil to the correct level, before the filter is removed. It is therefore recommended that the engine oil is renewed before work on the filter commences. 1. Clean the area around the filter head and place a suitable con[...]

Lubricants 138 Lubricants Using the correct grade and specification of lubricant is very important. Only use Land Rover recommended lubricants as shown in ’General data’. NOTE: Recommended oils are complete in themselves and additives should not be used. Transmission, transfer box, differentials & swivel pin housing It is essential to chang[...]

139 SECTION 5 General data Section Contents Page Lubricants & fluids 141 .................................. Capacities 143 ................................................ Engine data 144 .............................................. Steering 144 ................................................... Electrical system 145 ........................[...]

140[...]

General data 141 LUBRICANTS & FLUIDS Recommendations for all climates and conditions. COMPONENTS AMBIENT TEMPERATURE ° F Specification SAE -22 -4 14 32 50 68 86 104 122 Engine sump Oils must meet 5W/30 API service levels 5W/40, 5W/50 SG or SH 10W/30 10W/40, 10W/50 10W/60 Main gearbox, manual ATF M2C33 (F or G) or Dexron III* Main gearbox, auto[...]

General data 142 Lubrication nipples (hubs, ball joints, prop. shafts, etc.) NLGI-2 Multipurpose Lithium based grease. Brake and clutch reservoirs Universal brake fluids or any brake fluid having a minimum boiling point of 500 ° F (260 ° C) and complying with FMVSS 116 DOT4. Windscreen washers Screen washer fluid. Engine cooling system Ethylene g[...]

General data 143 CAPACITIES The following capacities are approximate and provided as a guide only. All oil levels must be set using the dipstick or level plugs as applicable. US units Imperial Metric WSM Fuel tank - usable capacity 23.4 US gal ................. 19.5 Imp gal 89,0 litre Engine sump 6.3 US quarts .................................... 1[...]

General data 144 ENGINE Bore 3.700 in (94,0 mm) ....................................................................... Stroke 2.800 in (71,12 mm) .................................................................... Number of cylinders 8 .............................................. Cylinder capacity 241 cu in (3950 cc) ...........................[...]

General data 145 ELECTRICAL SYSTEM Type Negative earth ...................................................................... Voltage 12 .................................................................. Battery 091/072 ................................................................... Charging circuit AC Generator (Alternator) ...................[...]

General data 146 DIMENSIONS Overall length (including spare wheel) 177.9 in (4521 mm) ................... Overall width 70.6 in (1793 mm) .......................................................... Overall height (open sunroof) 79.0 in (2005 mm) * ................................ Wheelbase 100 in (2540 mm) ...........................................[...]

General data 147 VEHICLE WEIGHTS Curb weight (with no options) 4453 lb (2020 kg) ............................... Max front axle weight 2668 lb (1210 kg) ............................................ Max rear axle weight 3572 lb (1620 kg) .............................................. Gross vehicle weight 6019 lb (2730 kg) ...........................[...]

General data 148 TYRE SIZE & PRESSURES Front Rear 205 R16 Radial Normal - all load conditions 28 psi ............................. 38 psi (2.0 kgf/cm 2 ) (2,6 kgf/cm 2 ) 235/70 R16 Radial Normal - all load conditions 26 psi ............................. 36 psi (1,8 kgf/cm 2 ) (2,5 kgf/cm 2 ) Wheel nut torque 130 Nm (96 lbf/ft) .................[...]

149 SECTION 6 Parts & accessories Section Contents Page Parts & accessories 151 ................................. Electrical equipment 152 ................................ Travelling abroad 152 ..................................... Recommended parts 153 ...............................[...]

150[...]

Parts & accessories 151 PARTS AND ACCESSORIES Your Land Rover Discovery has been designed, manufactured and proven to cope with the most rigorous driving conditions. As such, fitting parts and accessories that have been developed and tested to the same stringent standards is essential to guarantee the continued reliability, safety and performan[...]

Parts & accessories 152 Electrical equipment WARNING It is extremely hazardous to fit, or replace, parts or accessories whose installation requires the dismantling of, or addition to, either the electrical, fuel or SRS/airbag systems. Always consult your Land Rover dealer before fitting any electrical accessory. Fitting inferior quality parts o[...]

Parts & accessories 153[...]

Parts & accessories 154[...]

155 This section of your handbook is devoted to the Discovery’s superb off-road driving capabilities. Before venturing off-road however, it is absolutely essential that inexperienced drivers become fully familiar with the vehicle’s controls, in particular the transfer gearbox, and also study the off-road driving techniques described on the foll[...]

156[...]

Off-road driving 157 WARNING Off-road driving can be hazardous! DO NOT take unnecessary risks and be prepared for emergencies at all times. Your Discovery has a higher ground clearance and hence a higher centre of gravity than an ordinary passenger car. An abrupt manoeuvre at an inappropriate speed or on an unstable surface could cause the vehicle [...]

Off-road driving 158 Gear selection - automatic gearbox With the main selector lever set at ’3’, the gearbox automatically provides the correct gear. Remember that position ’1’ will hold the gearbox in first gear to give maximum engine braking when required. HIGH range gears should be used whenever possible - only change to LOW range when g[...]

Off-road driving 159 Ground clearance Don’t forget to allow for ground clearance beneath the chassis, axles, and under the front and rear bumpers. Note that the axle differentials are situated BELOW the chassis and are positioned slightly to the RIGHT of the centre of the vehicle. Note also that there are other parts of the vehicle which may come[...]

Off-road driving 160 DRIVING ON SOFT SURFACES & DRY SAND The ideal technique for driving on soft sand requires the vehicle to be kept moving at all times - soft ground and sand cause excessive drag on the wheels resulting in a rapid loss of motion once driving momentum is lost. For this reason, gear changing (particularly on manual gearbox vehi[...]

Off-road driving 161 CLIMBING STEEP SLOPES Engage the DIFF LOCK and ALWAYS follow the fall line of the slope - travelling diagonally could encourage the vehicle to slide broadside down the slope. Steep climbs will usually require the LOW gear range. If the surface is loose or slippery, use sufficient speed in the highest practical gear to take adva[...]

Off-road driving 162 DESCENDING STEEP SLOPES A. Stop the vehicle at least a vehicle length before the slope and engage first gear (selector position ’1’ for automatic gearbox cars) in LOW range with the differential locked. B. Unless it is necessary to stop the vehicle in order to negotiate obstructions, DO NOT touch the brake or clutch pedals [...]

Off-road driving 163 TRAVERSING A SLOPE Before crossing a slope ALWAYS observe the following precautions: • Check that the ground is firm and not slippery. • Check that the wheels on the downhill side of the vehicle are not likely to drop into any depressions in the ground and that the ’uphill’ wheels will not run over rocks, tree roots, or[...]

Off-road driving 164 CROSSING A RIDGE Approach at right angles so that both front wheels and then both rear wheels cross the ridge together - an angled approach could cause traction to be lost through diagonally opposite wheels lifting from the ground at the same time. CROSSING A DITCH With the DIFF LOCK engaged, cross ditches at an angle so that t[...]

Off-road driving 165 After wading • Drive the vehicle a short distance and apply the foot brake to check that the brakes are fully effective. • DO NOT rely on the parking brake alone to hold the vehicle stationary until the transmission and brakes have thoroughly dried out; in the meantime, use the wheel chock, or leave the vehicle parked in ge[...]

166[...]

Index 167 A ABS 83 ........................................................... Accessories 151 ............................................. Air cleaner renewal 134 .................................. Air conditioning 51 ......................................... Air vents 47 .................................................... Airbag SRS 29 ........[...]

Index 168 F Fan speed control 48 ...................................... Fluid specifications 141 .................................. Fog guard lights 43 ......................................... Fog lights (front) 44 ....................................... Front fog lights 129 ........................................ Fuel 68 & 147 ..............[...]

Index 169 Power assisted steering 64 ............................. Power steering top-up 109 ............................. R Radio remote controls 43 ............................... Rear fog guard lights 43 ................................. Rear light cluster 127 ..................................... Rear seats 22 ..................................[...]