Lathem 2121 инструкция обслуживания

Mechanical Time Recorder Model 2121 User’s Guide[...]

Contents Thank you for choosing the Lathem 2121 time recorder. Should you ever need assistance, please let us know. This guide contains all the information you need for setting up and operating your new time recorder. Service i nformation is also included for replacing certain parts. Ordering Accessories ........................... ................[...]

Model 2121 Time Recorde r User’s G uide Page 1 Ordering Accessories Lathem time recorders fulfill a wide range of ti mekeeping requirements. For maximum results, only use Lathem accessories specifically designed to fit your time recorder. To purchase the appropriate accessories for your Model 2121 time recorder, cont act your local Lathem dealer [...]

Model 2121 Time Recorde r User’s G uide Page 2 Start Here Complete these steps to setup your new time recorder This guide is available to download at: http://www.lathem.com/support/product-manuals.aspx 1. Mount Clock in Suitable Lo cation Must be within 6 feet of AC power source (unswitched) an d conveni ently located for yo ur employees. See att[...]

Model 2121 Time Recorde r User’s G uide Page 3 2.4 Place your hands on both sides of the cover and pull it toward you to remove i t. A small amount of for ce may be required. 3. Lift the T ype Se ction 3.1 Locate the lock lever on either side of the type s ection behind the clock face .[...]

Model 2121 Time Recorde r User’s G uide Page 4 3.2 While pushing the lock lever down, lift the entire type section as shown below until it locks into place horizontally. It will click distinctly when it locks place. 4. Set the Printed Day and T ime 4.1 Locate and press the red overthrow lever until it clicks. This releases the print wheels, allow[...]

Model 2121 Time Recorde r User’s G uide Page 5 4.2 Before setting type wheels, observe the center position of wheels, as shown by the arrows below. The characters in the center position of each wheel are the characters that will print. Rotate each wheel with your fingers or a pointed object clockwise until the correct day and time are aligned at [...]

Model 2121 Time Recorde r User’s G uide Page 6 4.3 When finished, release the red overthrow lever by gently pulling it toward you until it clicks. This prevents the print wheels from being manually turned. 5. Set Hands on Cl ock F ace 5.1 Locate the setting wheel on the right side below the clock face. Caution : Do not manually turn the hands on [...]

Model 2121 Time Recorde r User’s G uide Page 7 6. Advance Print Wheel s and Hands 6.1 Turn the main setting wheel, as shown below, to advance both the clock face and the print wheels together. 6.2 Use your fingers or a poi nted object to rotate the main setting wheel clockwise until it advances the time on the clock face to the curren t time. Eac[...]

Model 2121 Time Recorde r User’s G uide Page 8 7.2 While holding the type section up, release the latch by slightly pushing it in the direction, as shown below. 7.3 Gently lower the type section. Tip : Turn spools to tighten ribbon before lowering type section to avoid catching the ribbon. 7.4 Firmly push it into the clock until it clicks. 7.5 Pl[...]

Model 2121 Time Recorde r User’s G uide Page 9 8. T e st that Cloc k Is No w Set C orrectly 8.1 When the clock advances to the next minute, you hear a distinct click. 8.2 Insert a card or piece of paper below the print ribbon. 8.3 Push lever on front of the unit down to make a print. 8.4 Verify that the clock face time matches the printed time. I[...]

Model 2121 Time Recorde r User’s G uide Page 10 Change the Ribb on Lathem time recorders have self-reversing ribbons. With normal use, a ribbon should last for many months or even years. When the time comes, it is easy to change. 1. Remove cover and lift ty pe section as described in Unlock and Remove the Cover and Lift Type Section . 2. Use a po[...]

Model 2121 Time Recorde r User’s G uide Page 11 Change the T yp e Section If the type section needs servicing, you can easil y remove and change it without sending the entire unit for service. 1. Remove cover as des cribed in Unlock and Remov e the Cover . 2. Remove the type section retaining ring. 3. Press type section lock lever as shown on pag[...]

Model 2121 Time Recorde r User’s G uide Page 12 Change the Mot or 1. Unplug the unit from the AC electrical outlet. 2. Remove cover as des cribed in Unlock and Remov e the Cover . 3. Remove type section as described in Changing th e Type Section . 4. Disconnect the wire leads by turning each screw one-quarter turn counter-clockwise. 5. Remove the[...]

Model 2121 Time Recorde r User’s G uide Page 13 8. Install the new motor making sure the motor bracket is completely behind the clock frame and the gold motor bearing is resting in the slot of the frame. 9. Attach the type section, reset the time, and replace the cover, as described in this guide. T rouble Shooting Clock Loses Time on P rinter, b[...]

Model 2121 Time Recorde r User’s G uide Page 14 W arranty One-Yea r Limited W arrant y Lathem warrants the hardware products described in this guide against defects in material and workmanship for a period of one y ear fro m date of original purchase fro m Lathem or from an authorized Lath em resell er. The conditio ns of this warranty and the ex[...]