Lenco Marine CS-1004 инструкция обслуживания

OWNER’S MANUAL Mobile Audio System • PLL Synthesizer Stereo Radio • RDS (Radio Data System) Operation • Digital Compact Disc Player • Automatic Memory Storing • Full Detachable Panel •P r eset Equalization CS-1004 MP3[...]

CONTENTS Installation ...........................................3 T ake out screw befor e installation.........3 DIN Front-Mount (Method A) ................3 Installing the unit .................................3 Removing the unit ...............................4 DIN Rear -Mount (Method B) .................5 Using the detachable front panel ......[...]

INST ALLA TION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver . • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly . • Use only the parts included with the unit to en[...]

INST ALLA TION 6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver . Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appr opriate tabs behind the dashboard to secur e the sleeve in place. 7. Reconne[...]

DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (T oyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. To fasten the unit to the factory radio mounting brackets. 1. Use a scr ewdriver[...]

USING THE DET ACHABLE FRONT P ANEL REMOVING THE FRONT P ANEL 1. Pr ess the release button (REL) on the front panel and pull of f the front panel. 2. Keep fr ont panel into the case. INST ALLING THE FRONT P ANEL To install the front panel, insert the panel into the housing and make sure the panel is properly installed. Otherwise, abnormality occurs [...]

WIRING CONNECTION ISO Connection ISO SOCKET PIN OUT Part A Power Connection Part B Speaker Connection 1. Free 1 + 2. Free 2 – 3. Free 3 + 4. Memory (+B permanent) 4 – 5. T rip line for fully automatic antenna 5 + 6. Free 6 – 7. Main power supply (+B ignition) 7 + 8. Ground 8 – Part C 1. Audio frequency out, r ear left 2. Audio frequency out[...]

OPERA TION LOCA TION OF KEYS 14 4 2 16 17 13 8 9 10 7 11 1 12 3 20 21 6 22 23 19 18 15 5 24 GB-8[...]

OPERA TION SWITCHING ON/OFF THE UNIT Switch on the unit by pressing any button (except REL button (7) and EJECT button (4)). When system is on, press PWR button (9) to turn off the unit. F ACEPLATE RELEASE Press REL button (7) to detach the removable faceplate. SOUND ADJUSTMENT Press SEL button (10) shortly to select the desired adjustment mode. Th[...]

OPERA TION c) RETUNE L, RETUNE S mode The initial time of automatic T A search or PI sear ch mode is selected. When PI information is not caught for retune time, the radio start to retune to next same PI station. When same PI station does not catch 1 cyclic search, the radio goes to last station and waits for several minutes until PI code is receiv[...]

OPERA TION “NO PTY” -> Each displaying time is several seconds, and come back to 1’st position after several seconds. Notes: - CT = clock time - FREQ. = frequency EQUALIZA TION Press PEQ button (19) to turn on equalization function and to select desired audio mode. Ther e are five kinds of mode as below: LIQUID CR YST AL DISPLA Y Exhibit c[...]

OPERA TION immediately to switch on or off R.D.S. mode. Whenever R.D.S. is switched on, symbol “AF” appears on the display . Program name is displayed on receiving a R.D.S. station. “AF” starts blinking if the broadcasting signal getting worse. “ALARM” will be displayed when an emer gency broadcasting is r eceived; meanwhile sound outpu[...]

OPERA TION R.D.S. T A information was received from curr ent station and the radio switched to that R.D.S. linked station, but no information could not be received because the R.D.S. linked station is located too far from that area. So the radio is switched back to current station again. In above operation, a customer listen to a wrong program or m[...]

OPERA TION • PLA YING ALL TRACKS IN RANDOM Press SHF button (23) to play all tracks on CD in random order . Press again to cancel the function. • EJECTING A DISC Press EJECT button (4) to stop CD playing and eject the disc from the disc slot (5). Note: When you first play a CD and when whichever track is playing, press M5 button (24) or M6 (25)[...]

OPERA TION unit searches the track after few seconds, even if the enter button is not pressed. Searching Dir ectory or File Name Press AMS (MP3) button for two times. It enters into “Searching Dir ectory or File Name” in Digital Audio CD. The unit searches files and dir ectories that have the same character which is inputted by the user pressin[...]

OPERA TION KEY Assigned IN Searching mode (T able 1) AUDIO SELECT UP/DOWN & TUNE/SEEK/TRACK UP/DOWN buttons: Searching file and dir ectory during Navigation. MIXED-CD OPERA TION If available, the unit can play the mixed- CD disc (the disc contains both CD audio tracks and MP3 files). When you insert a mixed-CD disc into the CD slot, it starts t[...]

Recordable Rewritable DISC NOTES: A. Notes on discs : 1. Attempting to use nonstandard shape discs (e.g. square, start, heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2. Do not stick paper or tape etc., onto the label side or the recording side of any discs, as it may cause a malfunction. 3. Dirt, dust, scratche[...]

GENERAL Po w er Supply Requirements : DC 12 V olts, Negative Ground Chassis Dimensions : 178 (W) x 160 (D) x 50 (H) Tone Controls - Bass (at 100 Hz) : ± 10 dB - T r eble (at 10 KHz) : ± 10 dB Maximum Output P ow er : 4 x 15 W atts Current Drain : 5 Amper e (max.) CD PLA YER Signal to Noise Ratio : Mor e than 55 dB Channel Separation : Mor e than [...]

TROUBLE SHOOTING Before going thr ough the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer . Symptom Cause Solution No power . The car ignition switch is If the power supply is pr operly not on. connected to the car accessory terminal, switch the ignition key to[...]