Lennox Hearth LSBV-3628EN инструкция обслуживания

1 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. What to do if you smell gas: • DO NOT light any appliance. • DO NOT touch any electrical switches, do not use any phone in your building. • Immediately call your gas supplier from[...]

2 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. TABLE OF CONTENTS Packaging ........................................ page 2 Introduction ..................................... page 2 Massachusetts and New York Requirements ................................ page 2 General Information ......................... page 2 Location .......................[...]

3 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning are similar to the flu with headaches, dizziness and/or nausea. If you have these signs, obtain fresh air immedi- ately. Turn off the gas supply to the appliance and have it serviced by a qualified profes- sional, as it may not be [...]

4 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Venting Gas Vent Rule – Gas vent caps are not permit- ted within 8 feet (2.4 mm) of a vertical wall or similar obstruction. Gas vent caps that are located 8' or more from a portion of a building which extends at an angle greater than 45 ° upward from the horizontal may terminate in accordan[...]

5 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. FRAMING SPECIFICATIONS Figure 4 Figure 5 Figure 6 Framing Dimensions ASSEMBLY STEPS The typical sequence of installation follows, however, each installation is unique resulting in variations to those described. 1. Construct the appliance framing. 2. Route gas supply line to appliance location. 3. P[...]

6 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Step 3. Position the Appliance - Slide the fireplace into prepared framing or position fire- place in its final position and frame later. Refer to fireplace drawings and specifications on pages 4 and 5 for framing dimensions and details. Framing header may be positioned directly on the fireplace to[...]

7 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 10 Step 4. Install the Vent System & Exterior Termination - Slip a 10" (254 mm) B-Vent system over the appliance collar ( Figure 10 ) and secure with four sheetmetal screws (# 8 or larger). Minimum overall height of the vent system and appliance must be 12' (3.66 m) vertical (n[...]

8 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 14 1. Route a 3-wire 120V 60Hz power supply line to the appliance junction box wires and ground (Figures 13 ). 2. After wiring is complete, replace the appli- ance junction box cover and secure with the hex head screws previously removed. Step 6. Connecting Gas Line – Make gas line connect[...]

9 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 15 Note: Supply wires may be alternatively connected to the outlet using the screw terminals, however the black supply wire must be wired to a terminal that is opposite (across the outlet) the point where the white supply wire is connected ( Figure 15 ). Figure 16 CAUTION: NEVER LOCATE INLET[...]

10 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 17 Figure 18 Refer to the Homeowners Care and Operation Instructions for detailed log description and placement instructions. Log set shown in this document (Figure 17 ) is typical, installation of all sets are similar. APPLIANCE OPERATION Step 9. Checking the System – With gas line insta[...]

11 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 22 Adjustment To adjust the flame, position the air shutter to the nominal setting (Figure 22 ). Allow the burner to operate for at least 30 minutes. Observe the flame continuously. If it appears weak or sooty as previously described, adjust the air shutter open or closed until desired effe[...]

12 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. INSTALLATION ACCESSORIES The following accessory items are available for use in the installation of this appliance. Figure 24 COLD CLIMATE INSULATION If you live in a cold climate, seal all cracks around your appliance with noncombustible material and wherever cold air could enter the room. It is [...]

13 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Wall Switch Kit 85L87 FWSK Outside Combustion Air Kits (with duct) 81L87 FOAK-4 (without duct) 81L88 FOAK-4LD Outside Air Kits Models FOAK-4 and FOAK-4LD Outside Air kits are available with duct (FOAK-4) and without duct (FOAK-4LD) for use if outside combustion air is re- quired or desired. If mod[...]

14 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 25 Pressure Regulator Remove These Components Step 1. Turn off the gas supply to the appli- ance. Remove the front glass door (if used) from the appliance. Access the control com- partment. Step 2. Carefully remove the logs. Exercise care as not to break the logs. Step 3. Locate the screw s[...]

15 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 28 Figure 29 Step 9. Reassemble all removed components by reversing the procedures outlined in the preceding steps. Use pipe joint compound or Teflon tape on all pipe fittings before installing (ensure propane resistant compounds are used in propane applications, do not use pipe joint compo[...]

16 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2007 by Lennox Hearth Product[...]