Lenovo TS200V инструкция обслуживания

Installation and User Guide ThinkServer TS200v Machine T ypes: 0981, 0992, 1008, and 1010[...]

[...]

ThinkS e rv e r T S2 00v T yp es 098 1 , 0992, 1 008 , an d 1 0 1 0 In stall a ti o n a n d U s e r G ui d e[...]

Note Before using this information and the pr oduct it supports, be sure to r ead and understand the Safety Information book and “Notices,” on page 67. First Edition (March 2010) © Copyright Lenovo 2010. LENOVO products, data, computer softwar e, and services have been developed exclusively at private expense and are sold to governmental entit[...]

Contents Safety ............... v Chapter 1. Introduction ........ 1 Notices and statements in this document ..... 2 Related documentation ........... 3 Chapter 2. Server setup roadmap .... 5 Chapter 3. What is included with your server ............... 7 Features and specifications .......... 8 Software ................ 9 EasyStartup ..............[...]

Japanese compliance for products less than or equal to 20 A per phase ......... 7 1 Federal Communications Commission (FCC) and telephone company requir ements ....... 7 1 Canadian Department of Communications certification label ............ 7 2 Power cord notice ............ 7 2 Polyvinyl Chloride (PVC) cable and cord notice . . 74 T urkish state[...]

Safety Before installing this pr oduct, read the Safety Information. Antes de instalar este produto, leia as Informações de Segurança. Pred instal ací tohoto produktu si prectete prír ucku bezpecnostních instr ukcí. Læs sikkerhedsforskrifterne, før du installer er dette produkt. Lees voordat u dit pr oduct installeert eerst de veiligheidsv[...]

Antes de instalar este producto, lea la información de seguridad. Läs säkerhetsinformationen innan du installerar den här pr odukten. Important: Each caution and danger statement in this document is labeled with a number . This number is used to cross r eference an English-language caution or danger statement with translated versions of the cau[...]

Statement 1: DANGER Electrical current from power , telephone, and communication cables is hazardous. T o avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v[...]

Statement 2: CAUTION: When replacing the lithium battery , use only the battery recommended by the manufacturer . If your system has a module containing a lithium battery , replace it only with the same module type made by the same manufacturer . The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: v T[...]

Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. v Use of controls or adjustment[...]

Statement 4: ≥ 18 kg (39.7 lb.) ≥ 32 kg (70.5 lb.) ≥ 55 kg (121.2 lb.) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. T o remove al[...]

Statement 8: CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service tec[...]

CAUTION: The following label indicates a hot surface nearby . Statement 13: DANGER Overloading a branch circuit is potentially a fire hazard and a shock hazard under certain conditions. T o avoid these hazards, ensure that your system electrical requirements do not exceed branch circuit protection requirements. Refer to the information that is prov[...]

CAUTION: Do not place any object on top of rack-mounted devices. Statement 27: CAUTION: Hazardous moving parts are nearby . Statement 28: CAUTION: The battery is a lithium ion battery . T o avoid possible explosion, do not burn the battery . Exchange it only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regula[...]

xiv Installation and User Guide[...]

Chapter 1. Introduction This Installation and User Guide is intended to be used with your Lenovo ® ThinkServer ™ TS200v (Machine T ypes 0981, 0992, 1008, and 1010) server . This document contains information about: v Setting up and cabling the server v Starting and configuring the server v Installing options and replacing customer r eplaceable u[...]

The model number and serial number are on a label on the fr ont bezel, as shown in the following illustration: 1 Model number and serial number For a list of supported optional devices for the server , go to http://www .lenovo.com/thinkserver and click the Options tab. Notices and statements in this document The caution and danger statements [...]

Related documentation The Lenovo ThinkServer Documentation DVD contains documentation for the server in Portable Document Format (PDF). The Lenovo ThinkServer Documentation DVD requir es the Adobe ® Reader 5.0 (or later) or xpdf, which comes with Linux ® operating systems. The following table describes the content and location of documentation th[...]

4 Installation and User Guide[...]

Chapter 2. Server setup roadmap The installation process varies depending on the configuration of the server when it was delivered. In some cases, the server is fully configur ed and just needs to be connected to power and the network and started. In other cases, the server needs to have hardwar e features installed, requir es hardwar e and firmwar[...]

6 Installation and User Guide[...]

Chapter 3. What is included with your server The TS200v server package includes the server , a power cord, the ThinkServer Documentation DVD, and software media. 1 Server 2 Power cord 3 Documentation and software media © Copyright Lenovo 2010 7[...]

Features and specifications The following information is a summary of the features and specifications of the server . Depending on the server model, some features might not be available, or some specifications might not apply . T able 2. Features and specifications Microprocessor Y our server comes with one of the following micropr ocessors (intern[...]

T able 2. Features and specifications (continued) Dimensions W idth: 174.8 mm (6.88 inches) Height: 377.3 mm (14.85 inches) Depth: 406.7 mm (16.01 inches) W eight Maximum configuration: 1 1.2 kg (24.7 lbs) Environment Air temperature: Operating: 10° to 35°C (50° to 95°F) Non-operating: -40° to 60°C (-40° to 140°F) (with package) Non-operati[...]

10 Installation and User Guide[...]

Chapter 4. Server controls and connectors This chapter provides information about the server contr ols and connectors. Front view Figure 1 shows the locations of the controls and connectors on the fr ont of your server . 1 Hard disk drive activity LED 3 Power switch 2 Power-on LED 4 USB connectors (2) Figure 1. Front control[...]

Rear view Figure 2 shows the locations of the connectors on the rear of your server . Some connectors on the rear of your server ar e color-coded to help you determine where to connect the cables in your server . 1 Power cord connector 7 Microphone connector 2 Serial port 8 Audio line-out connector 3 VGA monitor connec[...]

Connector Description Audio line-in connector Used to receive audio signals fr om an external audio device, such as a stereo system. When you attach an external audio device, a cable connects the audio line-out connector of the device to the audio line-in connector of the server . Audio line-out connector Used to send audio signals from the server [...]

System-board internal connectors Figure 3 shows the locations of the parts and connectors on the system board. 1 4-pin power connector 11 eSA T A connector 2 Micropr ocessor 12 Power fan connector 3 Micropr ocessor fan connector 13 Front panel connector 4 DIMM 2 14 Clear CMOS (Complementary Metal Oxid[...]

Internal components Figure 4 shows the locations of the various components in your server . T o remove the server cover and access to the inside of the server , see “Removing the server cover” on page 18. 1 Heat sink and fan assembly 4 PCI car d 2 Memory module 5 Rear fan assembly 3 Optical drive 6 Power supp[...]

Internal drives Internal drives are devices that your server uses to r ead and store data. Y ou can add drives to your server to increase storage capacity and enable your server to read other types of media. Internal drives ar e installed in bays. In this manual, the bays are r eferred to as bay 1, bay 2, and so on. Figure 5 shows the locations of [...]

Chapter 5. Installing or replacing customer replaceable units This chapter provides instr uctions on how to install or replace customer replaceable units for your server . This chapter contains the following sections: v “Handling static-sensitive devices” v “Installing or replacing har dware” v “Installing security features” on page 46 [...]

2. When installing or replacing an option, use the appr opriate instructions in this section along with the instructions that come with the option. Installing external options Y ou can connect external options to your server , such as external speakers, a printer , or a scanner . For some external options, you must install additional software in ad[...]

6. Press the cover -release button on the side of the server and slide the cover to the rear of the server to r emove the cover . Removing and reinstalling the front bezel Attention Do not open your server or attempt any repair befor e reading and understanding the “Safety” on page v and the Safety Information book. T o obtain a copy of the Saf[...]

3. Remove the front bezel by r eleasing the three plastic tabs on the left side and pivoting the front bezel outwar d. 4. T o reinstall the front bezel, align the thr ee plastic tabs on the right side of the front bezel with the corr esponding holes in the chassis, then pivot the front bezel inward until it snaps into position on the left side. Wha[...]

T o install or replace a PCI card, do the following: 1. Remove all media from the drives and turn of f all attached devices and the server . Then, disconnect all power cords fr om electrical outlets and disconnect all cables that are connected to the server . 2. Remove the server cover . See “Removing the server cover” on page 18. 3. At the rea[...]

4. If you are installing a PCI car d, remove the appropriate metal slot cover . If you are r eplacing an old PCI card, grasp the old card that is curr ently installed and gently pull it out of the slot. Note: The PCI card fits tightly into the car d slot. If necessary , alternate moving each side of the PCI card a small amount until it is r emoved [...]

7. Pivot the PCI card latch to the closed position to secur e the PCI card. What to do next: v T o work with another piece of hardware, go to the appr opriate section. v T o complete the installation or replacement, go to “Completing the parts replacement” on page 44. Installing or replacing a memory module Attention Do not open your server or [...]

T o install or replace a memory module, do the following: 1. Remove all media from the drives and turn of f all attached devices and the server . Then, disconnect all power cords fr om electrical outlets and disconnect all cables that are connected to the server . 2. Remove the server cover . See “Removing the server cover” on page 18. 3. Lay t[...]

7. Position the new memory module over the memory slot. Make sure that the notch 1 on the memory module aligns correctly with the key 2 in the memory slot. Press the memory module straight down into the memory slot until the retaining clips close. 8. Reinstall all parts that have been removed. What to do next: v T o work with another pi[...]

v If you are r eplacing an optical drive, disconnect the signal cable and the power cable from the r ear of the optical drive, press the blue release button 1 , and then slide the optical drive out of the optical drive bay . 5. Install the optical drive retainer on the side of the new optical drive. Figure 14. Removing the optical drive Figur[...]

6. Slide the new optical drive into the optical drive bay from the fr ont of the server until the optical drive snaps into position. 7. Reinstall the front bezel. See “Removing and r einstalling the front bezel” on page 19. 8. Continue at “Connecting a SA T A drive.” What to do next: v T o work with another piece of hardware, go to the appr[...]

2. Locate an available five-wire power connector and connect it to the SA T A drive. Installing or replacing the secondary hard disk drive Attention Do not open your server or attempt any repair befor e reading and understanding the “Safety” on page v and the Safety Information book. T o obtain a copy of the Safety Information book, go to: http[...]

4. Press the r elease button 1 to release the secondary hard disk drive cage and then lift the cage out of the chassis. 5. Pull on the handle to release and r emove the blue hard disk drive bracket from the har d disk drive cage. 6. T o install the new hard disk drive into the blue bracket, flex the sides of the bracket properly and align pin[...]

7. Slide the new hard disk drive with the blue bracket into the secondary har d disk drive cage until it snaps into position. 8. Slide the hard disk drive cage with the new har d disk drive into the chassis until it is directly underneath the metal tab 1 . Figure 21. Installing the secondary hard disk drive 30 Installation and User Guide[...]

9. Press the har d disk drive cage downward until it snaps into position. Make sure that the har d disk drive cage is secured in the chassis. 10. Continue at “Connecting a SA T A drive” on page 27. Replacing the secondary hard disk drive Note: Depending on the model type, your server might have a secondary hard disk drive installed. T o replace[...]

5. Press the r elease button 1 to release the hard disk drive cage and then lift the hard disk drive cage out of the chassis. 6. Pull on the blue handle to release and r emove the hard disk drive from the hard disk drive cage. 7. Flex the sides of the blue bracket to remove the har d disk drive from the bracket. 8. Continue at “Installing a[...]

1. Remove all media from the drives and turn of f all attached devices and the server . Then, disconnect all power cords fr om electrical outlets and disconnect all cables that are connected to the server . 2. Remove the server cover . See “Removing the server cover” on page 18. 3. Disconnect the power supply assembly cables from the system boa[...]

Replacing the heat sink and fan assembly Attention Do not open your server or attempt any repair befor e reading and understanding the “Safety” on page v and the Safety Information book. T o obtain a copy of the Safety Information book, go to: http://www .lenovo.com/support This section provides instr uctions on how to replace the heat sink and[...]

6. Follow this sequence to remove the four scr ews that secure the heat sink and fan assembly to the system board: a. Partially remove scr ew 1 , then fully remove screw 2 , and then fully remove scr ew 1 . b. Partially remove scr ew 3 , then fully remove screw 4 , and then fully remove scr ew 3 . Note: Carefully[...]

10. Connect the heat sink and fan assembly cable to the micropr ocessor fan connector on the system board. See “System-boar d internal connectors” on page 14. What to do next: v T o work with another piece of hardware, go to the appr opriate section. v T o complete the replacement, go to “Completing the parts replacement” on page 44. Replac[...]

5. Press the blue r elease tab 1 downward, slide the hard disk drive cage 2 to the rear of the server , and then pivot it outward to completely remove the drive cage from the chassis. Then, pull on the blue handle 3 to r elease and remove the har d disk drive from the drive cage. 6. Flex the sides of the blue bracket to remove the[...]

7. T o install a new hard disk drive into the blue bracket, flex the sides of the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the har d disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Note: If you are installing a 2.5-inch har d d[...]

9. Align the hard disk drive cage pivot pin with the slot 1 in the upper drive cage, as shown in Figure 28. Then, slide the hard disk drive cage into the chassis. 10. Press down on the metal latch 2 and pivot the har d disk drive cage into place. Then, slide the drive cage to the front of the server until it snaps into position. Note: T[...]

11 . Connect the signal cable and the power cable to the new har d disk drive. See “Connecting a SA T A drive” on page 27. What to do next: v T o work with another piece of hardware, go to the appr opriate section. v T o complete the replacement, go to “Completing the parts replacement” on page 44. Replacing the front fan assembly Attention[...]

5. Release the two tabs 1 that attach the front fan assembly to the chassis as shown and then completely remove the fr ont fan assembly from the chassis. Figure 29. Removing the front fan assembly Chapter 5. Installing or replacing customer replaceable units 41[...]

6. Insert the two tabs 2 of the new front fan assembly into the corr esponding holes in the chassis, and press the other two tabs 1 thr ough the holes until the front fan assembly is secur ed in place. 7. Connect the new front fan assembly cable to the power fan connector on the system board. See “System-boar d internal connectors” [...]

Replacing the rear fan assembly Attention Do not open your server or attempt any repair befor e reading and understanding the “Safety” on page v and the Safety Information book. T o obtain a copy of the Safety Information book, go to: http://www .lenovo.com/support This section provides instr uctions on how to replace the r ear fan assembly . T[...]

7. Carefully pull on the tips of the r ubber mounts until the new rear fan assembly is secured in place. 8. Connect the new rear fan assembly cable to the system fan connector on the system board. See “System-boar d internal connectors” on page 14. What to do next: v T o work with another piece of hardware, go to the appr opriate section. v T o[...]

interference with r einstalling the server cover . 4. Position the server cover on the chassis so that the rail guides on the bottom of the server cover engage the rails on the chassis. Then, slide the cover to the front of the server until it snaps into position. 5. Install the screws to secur e the server cover . 6. Lock the server cover if you h[...]

Y ou can obtain device drivers for operating systems that are not preinstalled at http://www .lenovo.com/support. Installation instructions are provided in r eadme files with the device-driver files. Installing security features There ar e several security options available to help you prevent hardwar e theft and unauthorized access to your server [...]

Padlock Y our server is equipped with a padlock loop so that the cover cannot be removed when a padlock is installed. Password protection T o deter unauthorized use of your server , you can use the Setup Utility program to set a password. When you turn on your server , you are prompted to type the password. The server cannot be used until a valid p[...]

5. Move the jumper from the standar d position (pin 1 and pin 2) to the maintenance position (pin 2 and pin 3). 6. Reinstall all parts and reconnect all cables that have been r emoved. 7. Reinstall the server cover and reconnect the server power cor d. See “Completing the parts replacement” on page 44. 8. T urn on the server and leave it on for[...]

Chapter 6. Configuring the server This chapter provides instr uctions on how to configure your server . This chapter provides information on the following topics: v “Using the Setup Utility program” v “Configuring RAID” on page 52 v “Updating system programs” on page 54 v “Using the ThinkServer EasyStartup program” on page 56 v “I[...]

Using passwords By using the Setup Utility program, you can set passwor ds to prevent unauthorized access to your server and data. The following types of passwords ar e available: v Power-On Passwor d v Administrator Password v Hard Disk Passwor d Y ou do not have to set a password to use your server . However , using passwords improves computing s[...]

4. Follow the instructions on the right side of the scr een to set, change, or delete a password. Note: A password can be any combination of up to 64 alphabetic and numeric characters. For more information, see “Passwor d considerations” on page 50. Enabling or disabling a device This section provides information on how to enable or disable use[...]

Viewing or changing the startup device sequence This section provides instr uctions on how to view or permanently change the configured startup device sequence. T o view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program. See “Starting the Setup Utility pr ogram” on page 49. 2. Fro[...]

RAID Level Y our server must have the minimum number of SA T A hard disk drives installed for the supported level of RAID below: v RAID Level 0 – Striped disk array – T wo hard disk drives minimum – Better performance without fault tolerance v RAID Level 1 – Mirror ed disk array – T wo hard disk drives minimum – Improved read performanc[...]

10. Press Y when prompted to confirm the exit. Deleting RAID volumes This section describes how to use the Intel Matrix Storage Manager option ROM configuration utility to delete RAID volumes. T o delete RAID volumes, do the following: 1. Press Ctrl+I when pr ompted to enter the Intel Matrix Storage Manager option ROM configuration utility during t[...]

update the POST , the UEFI, and the Setup Utility program by starting your server with a flash update disc or running a special update pr ogram from your operating system. Lenovo might make changes and enhancements to the POST and UEFI. When updates are r eleased, they are available as downloadable files on the Lenovo W eb site at http://www .lenov[...]

3. Print these instructions. This is very important because they ar e not on the screen after the download begins. 4. Follow the printed instructions to download, extract, and install the update. Recovering from a POST/UEFI update failure If power to your server is interrupted while the POST/UEFI is being updated (flash update), your server might n[...]

v Initiates an unattended installation of the operating system and device drivers for most adapters and devices The program is contained on the ThinkServer EasyStartup DVD pr ovided with your server . If you did not receive the DVD with your server , you can download an ISO image of the DVD from http://www .lenovo.com/support. The program has a bui[...]

1. Insert the ThinkServer EasyStartup DVD and restart the server . If the EasyStartup program does not start, see “EasyStartup pr oblems” on page 60. 2. Follow the instructions on the scr een until you get to the Start option screen. 3. When the Start option screen is displayed, do the following: a. Insert the USB device that contains the respo[...]

Chapter 7. T roubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic pr ograms. If your server problem is not described her e, see Chapter 8, “Getting help and technical assistance,” on page 63 for additional troubleshooting r esources. This chapter provides information about the following topics: v “Ba[...]

Symptom Action The server beeps multiple times before the operating system starts. V erify that no keys are stuck. EasyStartup problems The following table describes the EasyStartup problems and suggested actions to correct detected pr oblems. T able 3. ThinkServer EasyStartup DVD v Follow the suggested actions in the order in which they are listed[...]

T o run the diagnostic program from a diagnostic disc that you cr eated, do the following: 1. T urn off your server . 2. Repeatedly press and r elease the F12 key when turning on the server . When the Please select boot device window displays, release the F12 key . 3. Select the optical drive of your choice as the first boot device. 4. Insert the d[...]

62 Installation and User Guide[...]

Chapter 8. Getting help and technical assistance If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sour ces available from Lenovo to assist you. This chapter contains information about where to go for additional information about Lenovo and Lenovo products, what t[...]

Getting help and information from the W orld Wide W eb On the W orld W ide W eb, the Lenovo W eb site has up-to-date information about Lenovo systems, optional devices, services, and support. For general information about Lenovo products or to pur chase Lenovo products, go to http://www .lenovo.com. For support on Lenovo products, go to: http://www[...]

Using other services If you travel with your computer or relocate it to a country wher e your desktop, notebook, or server machine type is sold, your computer might be eligible for International W arranty Service, which automatically entitles you to obtain warranty service throughout the warranty period. Service will be performed by service provide[...]

66 Installation and User Guide[...]

Appendix. Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the products and services curr ently available in your area. Any refer ence to a Lenovo product, program, or service is not intended to state or imply that only that Le[...]

vary significantly . Some measurements may have been made on development-level systems and there is no guarantee that these measur ements will be the same on generally available systems. Furthermore, some measur ements may have been estimated through extrapolation. Actual results may vary . Users of this document should verify the applicable data f[...]

Electronic emissions notices The following information applies to Lenovo server machine types 0981, 0992, 1008, and 1010. Federal Communications Commission Declaration of Conformity This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to prov[...]

European Union EMC Directive conformance statement This product is in conformity with the pr otection requirements of EU Council Directive 2004/108/EC on the appr oximation of the laws of the Member States relating to electr omagnetic compatibility . Lenovo cannot accept responsibility for any failure to satisfy the pr otection requirements r esult[...]

Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4: Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse B. Japanese VCCI Class B statement Japanese compliance for products less than or equal to 20 A per phase Federal Communications Commission (FCC) and telephone company requirements 1. This device complies with Part 68 o[...]

7. This device may not be used on coin service provided by the telephone company . Connection to party lines is subject to state tariffs. Contact your state public utility commission or corporation commission for information. 8. When ordering network interface (NI) service fr om the local Exchange Carrier , specify service arrangement USOC RJ1 1C. [...]

For units intended to be operated at 230 volts (U.S. use): Use a UL-listed and CSA-certified cord set consisting of a minimum 18 A WG, T ype SVT or SJT , three-conductor cor d, a maximum of 15 feet in length and a tandem blade, grounding-type attachment plug rated 15 amper es, 250 volts. For units intended to be operated at 230 volts (outside the U[...]

Power cord part number Used in these countries and regions 41R3224 or 41R3225 Abu Dhabi, Bahrain, Botswana, Brunei Darussalam, Channel Islands, Cyprus, Dominica, Gambia, Ghana, Grenada, Guyana, Hong Kong S.A.R. of China, Iraq, Ireland, Jor dan, Kenya, Kuwait, Liberia, Malawi, Malaysia, Malta, Myanmar (Burma), Nigeria, Oman, Qatar , Saint Kitts and [...]

European Union (EU) WEEE statement EU Only The WEEE mark applies only to countries within the European Union (EU) and Norway . Appliances ar e labeled in accordance with Eur opean Directive 2002/96/EC concerning waste electrical and electronic equipment (WEEE). The Directive determines the framework for the r eturn and recycling of used appliances [...]

disused components, such as a printed circuit boar d or drive, use the methods described above for collecting and recycling a disused computer or monitor . Disposing of disused lithium batteries from Lenovo computers A button-shaped lithium battery is installed on the system board of your Lenovo computer to provide power to the computer clock while[...]

Index A Administrator , password 50 advanced settings 52 assistance, getting 63 attention notices 2 audio line-in connector 13 audio line-out connector 13 B basic troubleshooting 59 boot-block recovery 56 C cable lock, security 46 caution statements 2 changing password 50 startup device sequence 52 CMOS, clearing 47 components, internal 15 connecto[...]

password (continued) setting, changing, deleting 50 password pr otection 47 passwords erasing 47 lost or forgotten 47 passwords, using 50 PCI card 20 installing, replacing 20 slots 20 power supply assembly , replacing 32 power-on self-test (POST) 54 Power-On, Passwor d 50 programs, updating system 54 protection, passwor d 47 R rear connectors 12 re[...]

[...]

Printed in USA[...]