LG Electronics W2284F инструкция обслуживания

M ake sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. S ee the label attached on the product and give the information to your dealer when you ask for service. W2284F User ’ s Guide[...]

A1 This unit has been engineered and manufactur ed to ensure your personal safety , however impr oper use may result in potential electrical shock or fir e hazards. In order to allow the proper operation of all safeguards incorporated in this display , observe the following basic rules for its installation, use, and servicing. On Safety Use only th[...]

A2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventil[...]

A3 Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect the signal cable . When attached, tighten the thumbscrews to secure the connection. 3. Connect the power cable with the AC-DC adapter (AC-DC power supply) [...]

A4 Connecting the Display T o attach or separate the back cap 1 . To attach the back cap, fix into the 2 holes as picture first then press the back cap to fit to the upper groove. 2 . To separate the back cap, hold the bottom part and pull it out. Kensington Security Slot Connected to a locking cable that can be purchased separately at most compute[...]

A5 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the monitor upside down holding only the stand base. The monitor may fall and get damaged or injure your foot. Tilt Range : -5˚~15˚ Warning: Do not put your hand (finger) between [...]

A6 Control Function Control Panel Functions MENU Button Use this button to enter or exit from the On Screen Display. FUN Button Use this button to enter EZ ZOOMING , 4:3 IN WIDE , PHOTO EFFEC T items, for more information, refer to page A14-A15. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these setting[...]

A7 Control Panel Functions This Indicator lights up as blue when the display is operating normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to blue LED blinking state. Use this button to turn the display on or off. Power Button Power Indicator Use this button to select an icon in the On Screen Display.[...]

A8 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Scr een Display Control system. A short example is given below to familiarize you with the use of the contr ols. The following section is an outline of the available adj[...]

A9 NOTE The order of icons may differ depending on the model (A9~A16 ). On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Scr een Display control, adjustment, and setting menus. E Z Z OO MIN G T o adjust the resolution 4: 3 IN WID E T o adjust the image size P H O T O E FFE C T N O RMA L T o a dj ust screen co[...]

A10 Sub-menus On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Y ou wer e introduced to the pr ocedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press [...]

A11 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. PICTURE PRESET RED[...]

A12 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description CLOCK PHASE SHARPNESS To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of cha[...]

A13 Restore all factory default settings except "LANGUAGE." Press the , buttons to reset immediately. On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. This function will be [...]

A14 A14 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description EZ ZOOMING The OSD screen will appear when you touch the FUN button on the left bottom of the monitor. EZ Zoom lowers the display’s resolution in single-step increments. Depressing the button once lowers the resolution by one step; while a second button-press r[...]

A15 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PHOTO EFFECT - NORMAL: The PhotoEffect function is disabled. - GAUSSIAN BLUR: This option is to add the effect to the screen that the dark and sharp image becomes brighter and more blurred. - SEPIA: This option changes the screen to be Sepia tone. The Sepia tone is b[...]

A16 On Screen Display(OSD) Selection and Adjustment Icons Menu Name Sub-menu Name Main menu Sub menu Description MOVIE INTERNET NORMAL DEMO USER The OSD screen will appear when you touch the button on the left bottom of the monitor. INTERNET : For text images (Word processing etc.) Select the sub-menu using the AUTO/SET button and save the YES valu[...]

A17 T roubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power on and the power indicator blue? ● Is the power indicator blue LED blinking? ● Do [...]

A18 A18 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the resu[...]

A19 T roubleshooting Have you installed the display driver? ● Have you installed the display driver? ● Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? • Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driv[...]

A20 Specifications NOTE Information in this document is subject to change without notice. Display Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions &Weight Tilt Range Power Input AC-DC Adapter Environmental Conditions Stand Base Signal cable Power cord 22 inches (55.8 cm) Flat Panel Active matrix-TFT LCD Anti-Glare co[...]

A21 Specifications Indicator On Mode Sleep Mode Off Mode blue Blue and white LED blinking Off LED Color MODE Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1 2 3 4 5 6 7 8 9 10 11 *12 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 105[...]

Digitally yours[...]