Lincoln 2011 MKS инструкция обслуживания

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 17 Message center 18 Entertainment Systems 31 AM/FM stereo with CDX6/MP3 31 Auxiliary input jack (Line in) 39 USB port 40 Satellite radio information 44 Navigation system 47 SYNC 威 47 Climate Controls 48 Dual automatic temperature control 48 Navigation system based climate [...]

Locks and Security 99 Locks 105 Anti-theft system 121 Seating and Safety Restraints 126 Seating 126 Safety restraints 139 Airbags 153 Child restraints 168 Tires, Wheels and Loading 185 T ire information 185 T ire inflation 187 T ire Pressure Monitoring System (TPMS) 200 V ehicle loading 206 T railer towing 212 Recreational towing 214 Driving 216 St[...]

Customer Assistance 279 Reporting safety defects (U.S. only) 285 Reporting safety defects (Canada only) 286 Cleaning 287 Maintenance and Specifications 296 Engine compartment 298 Engine oil 301 Battery 305 Engine coolant 307 Fuel information 313 Air filter(s) 331 Part numbers 335 Maintenance product specifications and capacities 336 Engine data 340[...]

CONGRATULATIONS Congratulations on acquiring your new Lincoln. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the followi[...]

Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol. CALIFORNIA Proposition 65 W arning W ARNING: Engine[...]

Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. W ARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury . W ARNING: Front seat mounte[...]

• How far (if at all) the driver was depressing the accelerator and/or the brake pedal; and • How fast the vehicle was travelling; and • Where the driver was positioning the steering wheel. This data can help provide a better understanding of the circumstances in which crashes and injuries occur . Note: EDR data is recorded by your vehicle on[...]

Additionally , when you connect to T raf fic, Directions and Information (if equipped, U.S. only) the service uses GPS technology and advanced vehicle sensors to collect the vehicle’ s current location, travel direction, and speed (“vehicle travel information”) only to help provide you with the directions, traffic reports, or business searche[...]

EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLE SPECIFIC INFORMATION For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this Owner’ s Guide. A market unique supplement may be supplied that complements this book. By referring to the mar[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Based Parking Aid System Stability Control System[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Flu[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work. If any light remains [...]

Engine coolant temperature (R TT): Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible, switch off the engine and let cool. Refer to Engine coolant in the Maintenance and Specifications chapter . Low fuel (R TT): Illuminates when the fuel level in the fuel tank is at or near empty . Refer to Fuel gauge in t[...]

On-board diagnostics (OBD-II) in the Maintenance and Specifications chapter . If the light is blinking, engine misfire is occurring which could damage your catalytic converter . Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately by your authorized dealer . W ARNING: Under engine misfir[...]

Airbag readiness: If this light fails to illuminate when the ignition is turned on, continues to flash or remains on, have the system serviced immediately by your authorized dealer . A chime will sound if there is a malfunction in the indicator light. Safety belt: Reminds you to fasten your safety belt. A Belt-Minder 威 chime will also sound to re[...]

Speed control: Illuminates when the speed control is engaged or when the ACC is engaged without following a vehicle. T urns off when the speed control system is disengaged or when the ACC is activated. Anti-theft system: Flashes when the SecuriLock 威 Passive Anti-theft System has been activated. T urn signal: Illuminates when the left or right tu[...]

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If the needle moves close to the “H” range, the engine is overheating. Stop the vehicle as soon as safely possible[...]

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is on). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The FUEL icon and arrow indicates which side of the vehicle the fuel filler door is located. Refer to Filling the tank in the Maintenance and Specifications chapter for m[...]

Info Press the INFO button repeatedly to cycle through the following features: TRIP A/B Registers the distance of individual journeys. Press and release INFO until the A or B trip appears in the display (this represents the trip mode). Press and hold RESET until it resets. Refer to UNITS later in this section to switch the display from Metric to En[...]

• V ariations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) T o determine your average highway fuel economy , do the following: 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel eco[...]

1. OIL LIFE 2. W ASHER FLUID LEVEL 3. DOOR AJAR ST A TUS 4. TRUNK AJAR/CLOSED 5. BRAKE SYSTEM 6. TIRE PRESSURE 7. FUEL LEVEL 8. MYKEY DIST ANCE (If MyKey™ is programmed) 9. MYKEY(S) PROGRAMMED 10. ADMIN KEYS PROGRAMMED Note: Some systems show a message only if a condition is present. OIL LIFE This displays the remaining oil life. An oil change is[...]

AUTOLAMP This feature keeps your headlights on for up to three minutes after the ignition is switched off. Press RESET to select the new Autolamp delay values of 0, 10, 20, 30, 60, 90, 120 or 180 seconds. AUTOLOCK This feature automatically locks all vehicle doors when the vehicle is shifted into any gear , putting the vehicle in motion. Press RESE[...]

Press RESET to turn it off or on. REAR P ARK AID (if equipped) This feature sounds a tone to warn the driver of obstacles near the rear bumper , and functions only when R (Reverse) gear is selected. Press RESET to turn it off or on. FRONT P ARK AID (if equipped) This feature sounds a tone to warn the driver of obstacles near the front bumper . Pres[...]

DRIVER DOOR AJAR — Displayed when the driver’ s door is not completely closed. P ASSENGER DOOR AJAR — Displayed when the passenger side door is not completely closed. REAR LEFT DOOR AJAR — Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR — Displayed when the rear right door is not completely closed. P ARK B[...]

TIRE PRESSURE SENSOR F AUL T — Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to T ire Pressure Monitoring System (TPMS) in the T ires, Wheels and Loading chapter . If the warning stays on or continues to come on, contact your aut[...]

CRUISE OFF (if equipped) — Displayed when the driver pressed the Cruise On/Off control and ACC was on. SET XXX MPH GAP ACC GAP (if equipped) — Displayed when ACC is active and driver has selected a GAP setting using the steering wheel control <---> button. CRUISE CANCELED (if equipped) — Displayed when the ACC system has been turned off[...]

NO KEY DETECTED (if equipped) — Displayed if the Intelligent Access Key is not detected by the system in the following three scenarios: • When the start/stop button is pressed in an attempt to either start the engine or cycle through the ignition states. • When the engine is running and a door is opened then closed. • When the vehicle’ s [...]

VEHICLE SPEED 80 MPH MAX — Displayed when a MyKey™ is in use and the Admin has enabled the MyKey speed limit and the vehicle speed is 80 mph (130 km/h). Refer to MyKey™ in the Locks and Security chapter for more information. SPEED LIMITED TO 80 MPH — Displayed when starting the vehicle and MyKey™ is in use and the MyKey speed limit is on.[...]

CANCELLED BY ADV TRAC EVENT (if equipped) — Displayed when the active park feature has been canceled due to the AdvanceT rac 威 system activating. Refer to Active park assist in the Driving chapter for more information. CANCELLED BY ABS EVENT (if equipped) — Displayed when the active park feature has been canceled due to the ABS activating. Re[...]

TO STOP ALARM ST AR T VEHICLE — Displayed when the perimeter alarm system is armed and the vehicle is entered using the key on the driver’ s side door . In order to prevent the perimeter alarm system from triggering, the ignition must be turned to start or on before the 12 second chime expires. See Perimeter alarm system in the Locks and Securi[...]

AUDIO SYSTEMS Premium/Premium plus AM/FM in-dash CD6/MP3 satellite compatible sound system W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Y our primary responsibility is [...]

Setting the clock CLOCK: Press to set the clock. The display will read SET TIME. Use the memory preset numbers (0–9) to enter in the desired time– hours and minutes and press OK. The clock will then begin from that time. AM/FM Radio / VOL (Power/V olume): Press to turn the radio on/off. T urn the knob to increase/decrease volume. If the volume [...]

T o activate: Press MENU repeatedly until RDS (ON/OFF) appears in the display . Use SEEK to toggle RDS ON/OFF . When RDS is OFF , you will not be able to search for RDS equipped stations or view the station name or type. CA T/FLD (Category/Folder): This feature allows you to select from various music categories. T o change RDS categories: Press MEN[...]

When the system has ejected the CD, the display will read REMOVE CD #. If you do not remove the CD the system will reload the disc. T o auto eject all loaded discs– Press and hold . The system will eject all discs and prompt you when to remove them. SEEK: Press SEEK to access the previous/next track. CA T (Category) / FLD (Folder): In MP3 mode on[...]

TUNE: T urn to go to the next / previous available SIRIUS satellite station. DIRECT : Press DIRECT then enter the desired channel (i.e. 002) using the memory preset buttons (0–9). If you only enter one digit, press OK and the system will go to that satellite channel. If you enter three digits, the system will automatically go to that channel, if [...]

SA TELLITE RADIO MENU: Press MENU when satellite radio mode is active to access. Press OK to enter into the satellite radio menu. Press SEEK to cycle through the following options: • CA TEGOR Y MENU- Press OK to enter category mode. Press SEEK to scroll through the list of available SIRIUS channel Categories (Pop, Rock, News, etc.) Press OK when [...]

d. DISABLE ALER TS/ENABLE ALER TS: Press OK to enable/disable the satellite alert status which alerts you when your selected songs are playing on a satellite radio channel. (The system default is disabled.) SONG ALERTS ENABLED/DISABLED will appear in the display . The menu listing will display the opposite state. For example, if you have chosen to [...]

F ADE: Press SEEK to adjust the audio between the back (B) and front (F) speakers. SPEED COMPENSA TED VOLUME: With this feature on, radio volume automatically gets louder with increasing vehicle speed to compensate for road and wind noise. The default setting is off. Use SEEK to adjust between SPEED OFF and levels 1–7: Increasing the level from 1[...]

Auxiliary input jack (Line in) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Y our primary responsibility is the safe operation of the vehicle. W e recommend against the[...]

6. Press AUX on the vehicle radio repeatedly until LINE, LINE IN or SYNC LINE IN appears in the display . Y ou should hear audio from your portable music player although it may be low . 7. Adjust the sound on your portable music player until it reaches the level of the FM station or CD by switching back and forth between the AUX and FM or CD contro[...]

Y our vehicle is equipped with a USB port inside your center console. This feature allows you to plug in media playing devices, memory sticks, and also to charge devices if they support this feature. For further information on this feature, refer to Accessing and using your USB port in the SYNC 威 supplement or Navigation System supplement. GENERA[...]

• W ipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not[...]

MP3 track and folder structure Y our MP3 system recognizes MP3 individual tracks and folder structure as follows: • There are two different modes for MP3 disc playback: MP3 track mode (system default) and MP3 folder mode. For more information on track and folder mode, refer to Sample MP3 structure in the following section. • MP3 track mode igno[...]

Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played. Other files will be ignored by the system. This enables you to use the same MP3 d[...]

• T errain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception. • Station overload: When you pass a ground based broadcast repeating tower , a stronger signal may overtake a weaker one and result in an audio mute. Unlike AM/FM audible st[...]

Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly . SA T F AUL T Internal module or system failure present. If this message does not clear within a short period of time, or with an ignition key cycle, your receiv[...]

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly . NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna. Y ou are in a location that is blocking the SIRIUS 威 signal (i.e., [...]

DUAL ZONE AUTOMATIC T EMPERATURE CONTROL WITH HEATED AND COOLED SEATS T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter . 1. : Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear the windshield of fog and thin ice. The sy[...]

4. : Distributes air through the instrument panel vents, floor vents, rear seat floor vents and de-mister vents. T o return to full automatic control, press AUTO. 5. : Distributes air through the instrument panel vents. T o return to full automatic control, press AUTO. 6. Passenger heated seat: Press to control the passenger heated seat. Refer to H[...]

11. AUTO / + – (Fan Speed Control): Press to engage automatic temperature control. Select the desired temperature using the temperature control. The system will automatically determine fan speed, airflow location, A/C on or off, and outside or recirculated air , to heat or cool the vehicle to reach the desired temperature. For manual fan speed co[...]

DUAL ZONE AUTOMATIC T EMPERATURE CONTROL WITH HEATED AND COOLED SEATS (NAVIGATION SYSTEM BASED–IF EQUIPPED) T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter . 1. Climate: Press to control the climate control system through the touch display screen. See T ouchscreen funct[...]

5. R Rear defroster: Press to activate/deactivate the rear window defroster . Refer to Rear window defroster later in this chapter for more information. This button will also activate the heated mirrors. 6. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear the windshield of fog and thi[...]

T OUCHSCREEN FUNCTIONS T emperature – Press the up and down arrows on the left side of the screen to increase/decrease the airflow temperature for the driver side of the vehicle. This control also adjusts the passenger side temperature when dual zone operation is disengaged. Press the up and down arrows on the right side of the screen to increase[...]

V OICE COMMANDS IN CLIMATE MODE Please refer to the V oice commands in climate mode section of the Navigation system supplement for more information on using voice commands with the climate control system. Operating tips • T o reduce fog build-up on the windshield during humid weather , select (defrost). • T o reduce humidity build-up inside th[...]

T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel and works to clear the rear window of fog and thin ice. The ignition must be on to operate the rear window defroster . The rear defroster [...]

HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the low beam headlamps on. Adaptive headlamps (if equipped) The headlamp beams move in the same direction as the steering wheel which provides more visibility when driving around curves. • W ithout adaptive headla[...]

Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights. When selected, the automatic high beam system is active, if equipped and if enabled. See Auto high beams later in this chapter . • T o turn autolamps on, rotate the control counterclockwise to . • T o turn autolamps off, rotate the con[...]

Fog lamp control W ith the ignition on, the fog lamps can be turned on when the headlamp control is pulled toward you and is in any of the following positions: • Parking lamps • Low beams • Autolamps (when active) The fog lamp indicator light will illuminate when the fog lamps have been turned on. The fog lamps will not operate when the high [...]

Operation - The high beam switch will not perform any function. Scenario 2: Conditions - The automatic high beam system is set to ON in the message center . The headlamp switch is in (auto lamps). The automatic high beam system has not turned the high beams on. Operation - The high beam switch can be used to turn the high beams on. They will then r[...]

Deactivating high beams The automatic high beams will deactivate if any of the following events occur: • An approaching vehicle’ s headlights or a preceding vehicle’ s tail lamps are detected. • The headlamp control is moved out of the autolamps position. • The vehicle speed falls below 27 mph (43 km/h). • The ambient light level is hig[...]

Note: The programming sequence will end if either of the following occur: • The vehicle speed is not zero. • The battery voltage is out of normal range. T roubleshooting If the automatic high beam camera becomes blocked, the high beams may not come on automatically . They will only activate when they are manually turned on with the multi-functi[...]

• the transmission must be out of the P (Park) position. W ARNING: Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions[...]

• (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of the headlamp bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). 3. T urn on [...]

TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Second row map lamps The second row lamps are located at the rear of the headliner above each outboard seat. The second row lamps light when: • any door is opened, • the top of the instrument panel dimmer switch is p[...]

BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin [...]

Function Number of bulbs T rade number Headlamp high beam/ low beam 2 D3S Front park/turn/ sidemarker lamp 2 3457AK (amber) Backup lamp 2 921 * Sidemarker lamp (rear) 2 LED * T ail lamp 2 LED T urn signal 4 HPC 16WY (amber) License plate lamp 2 168 * High-mount brake lamp 1 LED Fog lamp (if equipped) 2 H11 Map lamp 2 12V6W Dome/reading lamps 3 578 [...]

3. Locate the parking/turn signal lamp electrical connector and remove it by pulling it straight off. 4. Remove the bulb socket by turning it counterclockwise and pulling it straight out. 5. T o remove the bulb, pull it straight out of the bulb socket. Install the new bulb(s) in reverse order . Replacing rear brake/tail/turn and sidemarker lamp bul[...]

Replacing high-mount brake lamp bulbs Y our vehicle is equipped with an LED center high-mount stop lamp. It is designed to last the life of the vehicle. If replacement is required, it is recommended that you see your authorized dealer . Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position. 2. Remove the two scr[...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate toward you to decrease the speed of the wipers. Rain-sensing wipers (if equipped): The rain-sensing wipers will automatically activate when moisture is present on the windshield and the multi-function switch is set to one [...]

Courtesy wipe feature: One extra wipe will occur a few seconds after washing the front window to clear any excess washer fluid remaining on the windshield. Note: Do not operate the washer when the washer reservoir is empty . This may cause the washer pump to overheat. Check the washer fluid level frequently . Do not operate the wipers when the wind[...]

ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on the visor mirror lamp. Slide-on-rod feature Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: T o stow the visor back into the headliner , visor must be retracted before moving it back toward the windshield. OVERHEAD CONSOLE The appearanc[...]

Double bin compartment ELECTRONIC COMPASS The compass heading is displayed in the center integrated display (CID). The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy . Usually , w[...]

Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. T urn ignition to the on position. 3. Press and hold the 7 and 9 radio preset buttons together for approximately five seconds until ZONE XX appears in the CID. 4. Press and release the 7 and 9 radio preset buttons togeth[...]

2. T o calibrate, press and hold the 7 and 9 radio preset buttons together for approximately 10 seconds until CAL appears. Release the buttons. 3. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CAL display changes to the direction value (N, S, E, W , etc.). It may take up to five circles to complete calibration. 4. The co[...]

Auxiliary power point can be found in the following location: • On the center console • Inside the utility compartment • On the rear of the center console accessible from the rear seat Do not use the power point for operating the cigarette lighter element (if equipped). T o prevent the fuse from being blown, do not use the power point(s) over[...]

Press and pull the switches to open and close windows. • Press down (to the first detent) and hold the switch to open. • Pull up (to the first detent) and hold the switch to close. Rear window buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise. This noise can be alleviated by lo[...]

Press and hold the control on the transmitter to begin to close the windows and moon roof. Note: The ignition must be off and the accessory delay feature must not be activated in order for this feature to operate. Note: This feature can be disabled or enabled by your authorized dealer . W ARNING: T o avoid personal injury and vehicle damage, verify[...]

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror up or down and from side to side. W ARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror The interior rear view mirror and a driver’ s side exterior mirror have an auto-dimm[...]

EXTERIOR MIRRORS Power side view mirrors W ARNING: Do not adjust the mirror while the vehicle is in motion. T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror . 2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center[...]

SPEED CONTROL W ith speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal. W ARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Using speed control The speed controls are located on the steering wheel. The following buttons work with speed control: RE[...]

Resuming a set speed Press and release RESUME. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control T o set a higher speed: • Press and hold SET + until you get to the desired speed, then release. Y ou can also use SET + to operate the tap-up function. Press and release SET + to increa[...]

W ARNING: Always pay close attention to changing road conditions, especially when using Adaptive Cruise Control. Adaptive Cruise Control cannot replace attentive driving. Failing to follow any of the warnings below or failing to pay attention to the road may result in a collision, serious injury or death. W ARNING: Adaptive cruise control is not a [...]

3. Press and release the SET + control. The vehicle speed will be stored in the memory and the message center will display SET XXX MPH (your desired speed). 4. T ake your foot off the accelerator pedal. 5. The green cruise indicator light on the instrument cluster will illuminate if there are no vehicles detected in front of you, while the yellow A[...]

braking which is applied by the ACC system is limited and can be overridden by the driver applying the brakes. If the ACC system predicts that its maximum braking level will not be sufficient, an audible warning will sound while the ACC continues to brake. This is accompanied by the heads-up display; a red warning bar illuminating on the windshield[...]

Note: It is the driver’ s responsibility to select a gap appropriate to the driving conditions. Disengaging adaptive cruise control Press the brake pedal to disengage the adaptive cruise control. CRUISE CANCELLED will be displayed in the message center . Disengaging the adaptive cruise control will not erase your previous set speed. Overriding ad[...]

Resuming the set speed Press and release the RESUME control. This will automatically return the vehicle to the previously set speed. The set speed will display continuously in the message center while ACC is active. Note: RESUME should only be used if the driver is aware of the set speed and intends to return to it. Low speed automatic cancellation[...]

Turning of f cruise control Press the OFF button to turn off the cruise control. Note: When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. Detection issues The radar sensor has a limited field of vision. In some situations it may not detect vehicles at all or detect a vehicle later than expected. De[...]

• There may be issues with the detection of vehicles in front when driving into and coming out of a bend or curve in the road. In these cases ACC may brake late or unexpectedly . The driver should stay alert and intervene when necessary . ACC not available Several conditions exist which can cause ACC to deactivate or prevent ACC from activating w[...]

Cause Action The surface of the radar in the grille is dirty or obstructed in some way Clean the grille surface in front of the radar or remove the object causing the obstruction The surface of the radar in the grille is clean but the message remains in the display W ait a short time. It may take several minutes for the radar to detect that it is n[...]

STEERING WHEEL CONTROLS Radio control features – VOL + (V olume): Press to decrease or increase the volume. (Seek): Press to select the previous/next radio station preset, CD track or satellite radio station preset depending on which media mode you are in. MEDIA: Press repeatedly to scroll through available audio modes. SYNC 威 system hands free[...]

Navigation system/SYNC 威 hands free control features (if equipped) Press control briefly until the voice icon appears on the Navigation display to use the voice command feature. Press to activate phone mode or answer a phone call. Press and hold to exit phone mode or end call. For further information on the Navigation system/SYNC 威 system, refe[...]

T o open the dual panel moon roof: Press and release the SLIDE control. The moon roof will automatically open. If the sunscreen is closed, it will automatically open prior to opening the moon roof. W ARNING: When closing the dual panel moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the p[...]

POWER REAR SUNSHADE (IF EQUIPPED) Y our vehicle may be equipped with a power rear sunshade that covers the rear window of your vehicle. The control is located in the center console access bin next to the power point. Press the control to move the shade up or down. The power sunshade is equipped with an automatic, one-touch, auto down feature. T o s[...]

Do not use the HomeLink 威 W ireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet c[...]

• If the indicator light stays on constantly , programming is complete and your device should activate when the HomeLink 威 button is pressed and released. • If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with “Programming” Steps 4 through 6 to complete programming of a rolling code equipp[...]

• Continue to press and hold the HomeLink 威 button (note Step 2 in the Programming section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 . The indicator light will flash slowly and then rapidly after HomeLink 威 accepts the radio freq[...]

Reprogramming a single HomeLink 姞 button T o program a device to HomeLink 威 using a HomeLink 威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink 威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. W ithout releasing the HomeLink 威 button, follow Step 1 in th[...]

T o open the trunk with the outside release button: 1. Unlock the trunk with the transmitter or power door lock control. If the intelligent access transmitter is within 3 feet (1 meter) of the trunk, the trunk will unlock when you press the release button. 2. Press the release button located near the license plate. CARGO AREA FEATURES Cargo net (if[...]

KEYS Y our vehicle is equipped with two intelligent access keys which operate the power locks and the remote entry system. The IA key must be inside the vehicle in order to activate the push button start system. The IA key also contains a removable mechanical key blade that can be used to unlock the driver door . T o release the mechanical key blad[...]

MYKEY™ The MyKey™ feature allows you to program a restricted driving mode to promote good driving habits. All but one of the keys programmed to the vehicle can be activated as a MyKey™. The key will remain restricted until MyKey™ is disabled. Any remaining keys are referred to as an “administrator key” or admin key . The admin key can b[...]

Create a MyKey™ T o program MyKey™ on one of the keys programmed to the vehicle, insert the key that you want to make a MyKey™ into the ignition. For vehicles equipped with push button start, put the intelligent access key in the backup slot; see the Driving chapter for the location of the backup slot. T urn the ignition on. Use the message c[...]

5. Press SETUP to enter your choice. The next optional setting will be displayed. 6. Repeat Steps 4 and 5 until you are done changing the optional settings. Clear MyKey™ T o reset all MyKeys™ as admin keys, do the following: 1. T urn the vehicle on using the admin key . 2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 3. Press and [...]

V ehicles equipped with traditional keys: When using a Ford-approved remote start system, the default settings will recognize the remote start system as an additional admin key with its associated privileges. Owners of vehicles equipped with traditional keys should program the remote start system as a MyKey™ in addition to the key that they have [...]

T roubleshooting Condition Potential Causes Can’t create a MyKey™ • Key in the ignition is already a MyKey™. • Key in the ignition is the last remaining admin key (there always has to be at least one admin key). • Intelligent access key (if equipped) not in the backup slot — for vehicles with push button start. • SecuriLock 威 Pass[...]

Condition Potential Causes I accidentally programmed all keys as MyKeys™ • V ehicle has a remote start system that is recognized as an admin key . Refer to the Using MyKey™ with remote start systems section to reset all MyKeys™ as admin keys. No MyKey™ function with intelligent access key (push button start) (if equipped) • An admin key[...]

Smart unlocks The smart unlock feature is intended to prevent you from unintentionally locking your IA key inside your vehicle’ s passenger compartment. When you lock your vehicle using the driver or passenger power door lock control (with the door open), after you close the door the vehicle will search for an IA key in the passenger compartment.[...]

Autolock feature The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is on, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). The autolock feature repeats when: • any door is opened then closed while the ignition is on and the[...]

6. T o enable/disable the autolock feature, press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. T urn the ignition off. The horn will chirp once to confirm the procedure is complete. Keyless entry keypad autolock enable/disa[...]

Deactivating/activating autounlock feature Y our vehicle comes with the autounlock features activated; there are four methods to enable/disable this feature: • Through your authorized dealer , • by using a power door unlock/lock sequence, • using a keypad procedure, or • by using the instrument cluster message center . Refer to Message cent[...]

Keyless entry keypad autounlock enable/disable procedure 1. T urn the ignition off. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8a second time. 5. Release the 3 • 4. The use[...]

INTERIOR LUGGAGE COMPARTMENT RELEASE Y our vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle. T o o[...]

W ARNING: Do not leave children, unreliable adults, or animals unattended in the vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly . Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are pa[...]

If there are problems with the remote entry system, make sure to take ALL intelligent access keys with you to the authorized dealer in order to aid in troubleshooting the problem. Intelligent access W ARNING: Radio waves from the intelligent access system transmitters in the vehicle may affect certain implanted medical devices such as pacemakers or[...]

situation (refer to Intelligent access key in this chapter for more information on the location and use of the mechanical key blade). A mechanical key is needed for access if the IA key battery or vehicle battery is low . Push button start: Y our vehicle is equipped with a push button start system, which allows you to start your vehicle without usi[...]

Sounding a panic alarm Press to activate the alarm. The horn will sound and the turn lamps will flash for a maximum of three minutes. Press again or turn the ignition on to deactivate, or wait for the alarm to time out in three minutes. Note: The panic alarm will only operate when the ignition is off. Opening the trunk Press twice within three seco[...]

2. Press and hold button 1 for five seconds. A tone will be heard after about two seconds confirming memory position has been set. Continue to hold until a second tone is heard after five seconds. 3. W ithin three seconds press . 4. A tone will be heard when the transmitter programming is complete. 5. Press . 6. Repeat this procedure for memory 2 a[...]

2. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 3. Insert the new battery . Refer to the instructions inside the IA key for the correct orientation of the battery . Press the battery down to ensure that the battery is fully seated in the battery housing cavity . 4. Snap the battery cover [...]

The lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Illuminated exit • When all vehicle doors are closed, the ignition is turned off , the interior dome lamps, parking lamps and puddle lamps (if equipped) will illuminate. The lights will turn off if all the doors remain closed and • 25[...]

SECURICODE™ KEYLESS ENTRY SYSTEM The keypad, located near the driver’ s window , is invisible until touched and then it lights up so you can see and touch the appropriate buttons. Note: If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter your entry code more slowly . Y ou can use the keyless entry key[...]

4. For memory recall feature, enter the sixth digit 1 • 2 to store driver 1 settings or 3 • 4 to store driver 2 settings. Note: T ouching 5 • 6 ,7 • 8, or 9 • 0 keypad numbers as a sixth digit will not recall a driver memory setting. Note: The factory-set code cannot be associated with a memory setting. 5. The doors will lock then unlock [...]

two-stage unlocking, refer to the Central unlocking/two stage unlocking section earlier in this chapter . T o unlock all doors, enter the factory set code or your personal code, then press the 3 • 4 control within five seconds. Note: If equipped with intelligent access, if the intelligent access key is within 3 feet (1 meter) of the driver door ,[...]

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster . • When the ignition is off, the indicator will flash once every two seconds to indicate the SecuriLock 威 system is functioning as a theft deterrent. Automatic arming The vehicle is armed immediately after turning the ignition off. Automatic disarming The [...]

Note: A maximum of four intelligent access keys can be programmed to your vehicle. If you would like to replace a previously programmed access key with a new access key , or if you already have four access keys programmed to your vehicle, you must take your vehicle and all access keys to your authorized dealer to be erased and reprogrammed. Ensure [...]

PERIMETER ALARM SYSTEM The perimeter alarm system will help protect your vehicle from unauthorized entry . When the following types of unauthorized entry occur: • any door , the hood or the trunk is opened without using the keypad or the remote entry transmitter , • or if the ignition is turned on when using an invalid key , the perimeter alarm[...]

Disarming the system T o disarm the system, do any of the following: • Unlock the doors by pressing unlock on the remote entry transmitter . • Unlock the doors by using your keyless entry pad. • Enter the vehicle using intelligent access. • Press the panic control on the remote entry transmitter . The alarm system will still be armed, but t[...]

FRONT SEATING W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. W ARNING: Before returning the seatback to its original po[...]

T o adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint. Properly adjust the head restraint so that [...]

T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint. T o reinstall the adjustable head restraint, do the following: 1. Insert the two[...]

W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Adjusting the front power seat W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. W AR[...]

Press the front portion to tilt the seat. Press the control to move the seat forward, backward, up or down. Press the control to recline the seatback forward or rearward. Note: On vehicles with memory seats, to prevent damage to the seat, the power seats are designed to set a stopping position just short of the end of the seat track. If the seat en[...]

• Continue pressing the control for approximately two seconds; you will feel the seat bounce back slightly . Using the power lumbar support The lumbar control is located on the side of the seat cushion. Press the front of the control to adjust firmness. Press the rear of the control to adjust softness. Press the top of the control to raise the he[...]

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly . T o operate the heated seats: Press the heated seat symbol to cycle through the various heat settings and off. W armer settings are indicated by more indicator lights.[...]

• There is a filter located under each front seat. • The filter can be accessed from the rear of the seat. Move the front seat to full up to ease access. T o remove an air filter: 1. Remove key from ignition. 2. Push up on the outside rigid edge of the filter until the tabs are released, then rotate the air filter toward the front of the vehicl[...]

T o install a filter: 1. First, position the filter in itshousing making sure that the far forward end is all the way up in the housing. 2. Push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position. Memory seats/power mirrors/steering column This system allows automatic positioning of the dr[...]

Easy entry/exit feature This feature automatically moves the steering wheel all the way up and in and moves the driver’ s seat rearward 2 in. (5 cm) when: • the transmission is in N (Neutral) or P (Park) • the ignition is turned off The seat and steering wheel will move to the original position when: • the transmission is in N (Neutral) or [...]

T o remove the non-adjustable head restraint, do the following: 1. Simultaneously press and hold both unlock/remove buttons, then pull up on the head restraint. T o reinstall the non-adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks. W ARNING: The non-a[...]

Seat-mounted cup holders and armrest storage compartment Cup holders and a storage compartment are located in the rear seat armrest. T o access the cup holders, rotate armrest into use position. T o open the storage compartment, pull up on the latch. W ARNING: Use only soft cups in the cupholder . Hard objects can injure you in a collision. Seating[...]

Armrest pass-through Pull down the door located in back of the armrest in order to store cargo of a longer length such as skis or lumber . Note : Do not exceed 80 lb (36 kg) of weight on the pass-through door . Rear heated seats W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord[...]

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly . The heated seat control is on the back of the front center console. T o operate the heated seats: • Push the indicated side of the control for maximum heat. • Push[...]

• Front outboard safety belts with pretensioners, energy management retractors (first row only), and safety belt usage sensors. • Driver’ s seat position sensor . • Front passenger sensing system • “Passenger airbag off” or “pass airbag off” indicator lamp • Front crash severity sensor . • Restraints Control Module (RCM) with [...]

information early in the crash event on the severity of the impact. This allows your Personal Safety System to distinguish between different levels of crash severity and modify the deployment strategy of the dual-stage airbags and safety belt pretensioners. Driver ’s seat position sensor The driver’ s seat position sensor allows your Personal S[...]

Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Personal Safety System to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage. Front safety belt pretensioners The[...]

Safety belt precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. W ARNING: T o reduce the risk of injury , make sure children sit where they can be properly restrained. W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot pro[...]

W ARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident. Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is secure[...]

Pregnant women should always wear their safety belt. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow . The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest. Safety belt locking modes All safe[...]

How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the a[...]

W ARNING: BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checked by an authorized dealer . Failure to replace the belt and retractor assembly could increase the risk of injury in collisions. Energy management featur[...]

W ARNING: Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt height adjustment Y our vehicle has safety belt height adjustments for the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o adjust the shoulder belt height, squeeze t[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition is on... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The safety belt warning lig[...]

If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition is switched on or less than 1-2 minutes have elapsed since the ignition has been switched on... The Belt-Minder 威 feature will not activate. The driver’ s or front passenger’ s safety belt is not buckled when the vehicle has reached at least 3 [...]

Reasons given... Consider ... “Belts are uncomfortable” W e design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. “I was in a hurry” Prime time for an accident. Belt-Minder 威 reminds u[...]

W ARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s airbag system. Deactivating/activating the Belt-Minder 姞 feature The driver and front passenger Belt-Minder 威 are deactivated/activated independently .[...]

3. W ait 10 seconds after the safety belt warning light turns off. • Step 4 must be completed within 20 seconds after the completion of Step 3. 4. For the seating position being disabled buckle then unbuckle the safety belt three times at a moderate speed, ending in the unbuckled state. • After Step 4, the safety belt warning light will be turn[...]

Important supplemental restraint system precautions Airbags DO NOT inflate slowly or gently and the risk of injury from a deploying airbag is greatest close to the trim covering the airbag module. W ARNING: All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restrain[...]

W ARNING: Do not put anything on or over the airbag module. Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury . W ARNING: Do not attempt to service, repair , or modify the airbag supplemental restraint system (SRS) or its fuses. See your authori[...]

How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the sys[...]

W ARNING: If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger airbag modules (which include the inflators and airbags). • side airbags and Safety Canopy [...]

• the system determines that an infant is present in a rear -facing infant seat that is installed according to the manufacturer’ s instructions, • the system determines that a small child is present in a forward-facing child restraint that is installed according to the manufacturer’ s instructions, • the system determines that a small chi[...]

• When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front passenger’ s seat, but the ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator lamp is lit, it is possible that the person isn’t sitting[...]

W ARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor . The front passenger sensing system may d[...]

W ARNING: T o reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pas[...]

W ARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the W arning light[...]

W ARNING: Do not attempt to service, repair , or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. Contact your authorized dealer as soon as possible. W ARNING: All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided. How does the side airbag system work? The design and[...]

The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activation. Side airbags are designed to inflate in side-impact collisions, not roll-over , rear -impact, frontal or near -frontal collisions, unless the collision caus[...]

W ARNING: Do not attempt to service, repair , or modify the Safety Canopy 威 system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy 威 . See your authorized dealer . W ARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety [...]

• T wo crash sensors mounted on the base of the B pillar or doors depending on the application (one on each side of the vehicle). • T wo crash sensors located at the C pillar behind the rear doors (one on each side of the vehicle). • Rollover sensor in the restraints control module (RCM). The Safety Canopy System, in combination with safety b[...]

W ARNING: If the Safety Canopy System has deployed, the safety canopy will not function again unless replaced. The Safety Canopy System (including the A, B and C pillar trim and headliner) must be inspected and serviced by an authorized dealer . If the safety canopy is not replaced, it will not function again, which will increase t h er i s ko fi n[...]

• or pressing the panic button on the remote entry transmitter . The feature will continue to operate until the vehicle runs out of power . Disposal of airbags and airbag equipped vehicles For disposal of airbags or airbag equipped vehicles, see your authorized dealer . Airbags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHI[...]

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat). Small children Children who have outgrown or no[...]

Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA TCH (lower anchors only) Safety belt and top tether anchor Safety belt and LA TCH (lower anchors and top tether anchor) Safety belt only Rear facing [...]

W ARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’ s size, height, weight, or age. Follow the child restraint manufacturer’ s instructions and warnings provided for installation and use in conjunction with the ins[...]

training to ensure that all children ages 0 to 16 are properly restrained in the correct restraint system. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician (CPST) and your pediatrician to make sure your seat is appropriate for your child and properly installed in the vehicle. T o locate a child seat fitting station[...]

Airbags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat all the way back. Children 12 and under should be properly restrained in a rear seating position whenever possible. If all children cannot be sea[...]

1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure th[...]

4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull[...]

9. Attach the tether strap (if the child seat is equipped). Refer to Attaching child safety seats with tether straps later in this chapter . 10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to [...]

Y our vehicle has LA TCH lower anchors for child seat installation at the seating positions marked with the child seat symbol. The LA TCH anchors are located at the rear section of the rear seat between the cushion and seatback, below the locator symbols on the seat back. Follow the child seat manufacturer’ s instructions to properly install a ch[...]

W ARNING: Never attach two child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor , if applicable. T ug the chil[...]

The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor . Once the child safety seat has been installed, using either the safety belt, the lo[...]

3. Open the tether anchor cover . 4. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 5. T ighten the child safety seat tether strap according to the manufacturer’ s instructions. If the safety seat is not anchored properly , [...]

Although the lap/shoulder belt will provide some protection, children who have outgrown a typical child seat are still too small for lap/shoulder belts to fit properly , and wearing an improperly fitted vehicle safety belt could increase the risk of serious injury in a crash. T o improve the fit of both the lap and shoulder belt on children who hav[...]

T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head [...]

Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to [...]

Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision. Child restraint and safety belt maintena[...]

INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING T ire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • T readwear 200 T raction AA T emperature A These T ire Quality Grades are determined by standards th[...]

W ARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. T emperature A B C The temperature grades are A (the highest), B and C, representing the tire’ s resistance to the generation of heat and its ability to [...]

Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability . • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an [...]

W ARNING: Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also [...]

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve [...]

Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydropla[...]

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification[...]

W ARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi (1.3[...]

• Do not run over curbs or hit the tire against a curb when parking W ARNING: If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. W ARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires[...]

• Front-wheel drive (FWD) vehicles (front tires at top of diagram) • Rear -wheel drive (RWD) vehicles/Four -wheel drive (4WD)/All-wheel drive (A WD) vehicles (front tires at top of diagram) Tires, Wheels and Loading 194 201 1 MKS (mks) Owners Guide, 1st Printing USA (fus)[...]

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y our vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel[...]

3. 65: Indicates the aspect ratio which gives the tire’ s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that rela[...]

8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For exa[...]

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’ s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or T ir[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. T ire Quality Grades do not apply to this type of tire. 1. T: Ind[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard[...]

The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The [...]

Understanding your tire pressure monitoring system (TPMS) The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning lamp will turn on if the tire pressure is significantly low . Once the light is illuminated, your tires are under inflated and nee[...]

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn you when your tires need air . It can also warn you in the event the system is no longer capable of functioning as intended. Please refer to the following chart for information concerning your tire pressure monitoring system: L[...]

Low tire pressure warning light Possible cause Customer action required Flashing warning light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system functions under these conditions, refer to When your temporary spare[...]

SNOW TIRES AND CHAINS W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death. Add[...]

V EHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, [...]

W ARNING: The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available. Overloading or improperly loading you[...]

Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating[...]

• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury . Tires, Wheels and Loading 209 201 1 MKS (mks) Owners Guide, 1st [...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’ s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers fr[...]

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 = -103 kg. Y ou will need to reduce the load weight by at least 240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, then the load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now you have the load capacity to transport the ceme[...]

Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety ch[...]

• It is recommended to select the “M” gear position when additional engine braking is needed. In situations such as prolonged downhill driving on steep grades (i.e., driving in mountainous areas), additional engine braking is needed to reduce the load on the vehicle’ s regular brake system to prevent them from overheating. For more informat[...]

These guidelines are designed to prevent damage to your vehicle. Front-wheel drive (FWD) vehicles: T ow your FWD vehicle with all four wheels on the ground or with the front wheels off the ground by using a tow dolly . If you are using a tow dolly follow the instructions specified by the equipment provider . All-wheel drive (A WD) vehicles: T ow yo[...]

STARTING Ignition modes 1. Off — This position shuts the engine and all electrical accessories off. Press and release the ST ART/STOP button without applying the brake pedal when your vehicle is in accessory or on modes or when the engine is running. Note: When the vehicle is in motion, a single press and release of the ST ART/STOP button will no[...]

W ARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. W ARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the en[...]

• Make sure the gearshift lever is in P (Park). Push button start system Y our vehicle is equipped with the push button start system. Y ou can start your vehicle by pressing the start button in combination with the brake pedal rather than using a key . The start button is located on the instrument panel to the right of the steering wheel. In orde[...]

cranking speeds; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel. There may be areas inside your vehicle where the IA key is not detected. If the message NO KEY DETECTED appears on your message center when you press the ST ART/STOP button, it may be necessary to move your IA key to another area wit[...]

Switching the V ehicle Off when not in P (Park): It is recommended that you shift into the P (Park) position before switching your vehicle off. If you switch your vehicle off with the shifter in any position other than P (Park), the message SHIFT TO P ARK will be displayed in the message center . If the vehicle is left in this state, your key in ig[...]

ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant which aids in starting and allows the heater/defroster system to respond quickly . If your vehicle is equipped with this system, your equipment includes a heater element which is installed in your engine block and a wire harness which allows the user to connect the sy[...]

• Be sure that areas where the vehicle is parked are clean and clear of all combustibles such as petroleum products, dust, rags, paper and similar items. • Be sure that the engine block heater , heater cord and extension cord are solidly connected. A poor connection can cause the cord to become very hot and may result in an electrical shock or [...]

Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an anti-lock braking system (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsation may be observed during ABS braking and the brake pedal may suddenly travel a litt[...]

Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned on) until the parking brake is released. W ARNING: Always set the parking brake f[...]

ADVANCET RAC 姞 STABILITY ENHANCEMENT SYSTEM Y our vehicle is equipped with the AdvanceT rac 威 system. The AdvanceT rac 威 system provides the following stability enhancement features for certain driving situations: • T raction control system (TCS), which functions to help avoid drive-wheel spin and loss of traction. • Electronic stability [...]

The AdvanceT rac 威 system automatically enables each time the engine is started. All features of the AdvanceT rac 威 system (TCS and ESC) are active and monitor the vehicle from start-up. However , the system will only intervene if the driving situation requires it. The AdvanceT rac 威 system includes one of these traction control off buttons l[...]

Excessive wheel spin is controlled in two ways, which may work separately or in tandem, engine traction control and brake traction control. Engine traction control works to limit drive-wheel spin by momentarily reducing engine power . Brake traction control works to limit wheel spin by momentarily applying the brakes to the wheel that is slipping. [...]

Switching off AdvanceT rac 威 If the vehicle is stuck in snow , mud or sand, and seems to lose engine power , switching off certain features of the AdvanceT rac 威 system may be beneficial because the wheels are allowed to spin. This will restore full engine power and will enhance momentum through the obstacle. T o turn off the AdvanceT rac 威 s[...]

AdvanceT rac 威 Features Control switch functions Mode Stability control off light Message center dis- play (if equipped) ESC TCS Default at start-up System Ini- tialization T urns on during bulb check Nothing dis- played En- abled En- abled Control switch pressed once mo- mentarily T raction control OFF On TRACTION CONTROL OFF En- abled Dis- able[...]

W ARNING: The EPS system has diagnostics checks that continuously monitor the EPS system to ensure proper operation of the electronic system. When an electronic error is detected, the message POWER STEERING ASSIST F AUL T will be displayed in the message center . If this happens, stop the vehicle in a safe place, and turn off the engine. After at l[...]

• uneven tire wear • loose or worn suspension components • loose or worn steering components • improper vehicle alignment A high crown in the road or high crosswinds may also make the steering seem to wander/pull. BRAKE-SHIFT INTERLOCK This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being[...]

P (Park) This position locks the transmission and prevents the front wheels from turning. T o put your vehicle in gear: 1. Press the brake pedal 2. Move the gearshift lever into the desired gear T o put your vehicle in P (Park): 1. Come to a complete stop 2. Move the gearshift lever and securely latch it in P (Park) W ARNING: Always set the parking[...]

T o return to normal D (Drive) position, move the shift lever back from M (manual) to D (Drive). The transmission will operate in gears one through six. Understanding your SelectShift Automatic™ T ransmission (SST) This vehicle is equipped with a SelectShift Automatic™ transmission (SST) gearshift lever . SST is an automatic transmission with t[...]

Recommended shift speeds Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 15 mph (24 km/h) 2 - 3 25 mph (40 km/h) 3 - 4 40 mph (64 km/h) 4 - 5 45 mph (72 km/h) 5 - 6 50 mph (80 km/h) The instrument cluster will show the current selected gear you are in. In order to prevent th[...]

FORWARD (IF EQUIPPED) AND REVERSE SENSING SYSTEMS The forward and reverse sensing system will warn the driver of obstacles within a certain range of the front and rear bumpers. The front sensors will be active when the gearshift is in any position other than P (Park) or N (Neutral) and the vehicle speed is below 8 mph (13 km/h). The rear sensors wi[...]

The reverse sensing portion of the system detects obstacles up to 6 ft (2 m) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the illustration for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) [...]

W ARNING: This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground. W ARNING: Certain add-on devices such as large[...]

Note: If the system cannot be turned off, refer to MyKey™ in the Locks and Security chapter for more information. The system defaults to enabled every time the ignition is switched on. Press the control to disable or enable the system Keep the sensors (located on the front and rear bumper/fascia) free from snow , ice and large accumulations of di[...]

Use the side mirrors and rearview mirror to get better coverage on both sides and rear of the vehicle. After shifting out of R (Reverse) and into any gear other than P (Park), the image will remain until the vehicle speed reaches 5 mph (8 km/h), only if the rear camera delay feature is on, or until any navigation radio button is pressed. Note: The [...]

either of the lamps are not operating, stop using the camera system, at least in the dark, until the lamp(s) are replaced and functioning. Servicing • If the image comes on while the vehicle is not in R (Reverse), have the system inspected by your authorized dealer . • If the image is not clear , then check if there is anything covering the len[...]

For best performance, the driver should drive the vehicle as parallel as possible while passing a parking space. If driven too fast (above 18 mph [30 km/h]) for the system to measure parking spaces, the message center will display ACTIVE P ARK REDUCE SPEED. When the system has found a space, the message center will display SP ACE FOUND PULL FORW AR[...]

When you determine the vehicle is back far enough or you hear a solid tone from the reverse sensing system, bring the vehicle to a complete stop and move the gearshift to D (Drive). The message center will now display PULL FORW ARD USE CAUTION followed by a chime. When you determine the vehicle is far enough forward or a solid tone from the forward[...]

• Exceeding a vehicle speed of 6 mph (10 km/h) during automatic steering • Deactivating the AdvanceT rac 威 system or the system has activated on a slippery or loose surface • ABS activation or failure • Any door (except the driver’ s door) opens • Something touching the steering wheel If a fault is present in the system, the message A[...]

• The driver allows the vehicle to roll in the opposite direction of the transmission (such as rolling forward when R (Reverse) gear is selected. • Y ou may be driving in R (Reverse). AP A can only look for a parking space while moving forward. • There may be an irregular curb along the parking space. AP A might not be able to align the vehic[...]

W ARNING: The collision warning system with brake support cannot help prevent all collisions. Do not rely on this system to replace driver judgment and the need to maintain distance and speed. Note: The collision warning with brake support will not detect, warn, or respond to potential collisions with vehicles to the rear or sides of the vehicle. O[...]

• Small distance to vehicle ahead. • Steering wheel and pedal movements are large (very active driving style). • High interior temperatures, which may deactivate the illumination or the warning lamps until the interior temperature reduces (audible warning will alert the driver). In addition, sun load and sunglasses may reduce the visibility o[...]

Cause Action Heavy rain, spray , snow , or fog is interfering with the radar signals Do not use the collision warning system in these conditions because it may not detect, warn, or respond to potential collisions Swirling water , or snow or ice on the surface of the road may interfere with the radar signals Do not use the collision warning system i[...]

Driving with blind spot mirrors Before a lane change, check the main mirror first, then check the blind spot mirror . If no vehicles are present in the blind spot mirror and the traffic in the adjacent lane is at a safe distance, signal that you are going to change lanes. Glance over your shoulder to verify traffic is clear , and carefully change l[...]

If your vehicle is equipped with A WD, a spare tire of a different size other than the tire provided should never be used. If the spare tire is installed, the A WD system may disable automatically and enter front-wheel drive only mode to protect driveline components. This condition may be indicated by an A WD OFF message in the message center (see [...]

• Be extremely careful when driving on pavement made slippery by loose sand, water , gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the st[...]

W ARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander . Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over -driving” your vehicle (i.e., turn the steering wheel only as rapidly and as far as required to avoid th[...]

Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the wheel rims (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall. Once through water , always try the brakes[...]

possibly rolling over . Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer . When climbing a steep slope or hill, start in a lower gear rather than downshifting to a low[...]

Make sure you allow sufficient distance between you and other vehicles for stopping. Drive slower than usual and consider using one of the lower gears. In emergency stopping situations, apply the brake steadily . Since your vehicle is equipped with a four wheel anti-lock brake system (ABS), do not “pump” the brakes. Refer to the Brakes section [...]

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water , traction or brake capability may be limited. Also, wate[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24-hours, seven days a week • for the coverage period listed on the Roadside[...]

Owner Guide portfolio in the glove compartment. In Canada, the card is found in the W arranty Guide in the glove compartment. U.S. Ford, Mercury and Lincoln vehicle customers who require Roadside Assistance, call 1-800-241-3673. Canadian customers who require roadside assistance, call 1-800-665-2006. If you need to arrange roadside assistance for y[...]

In some instances the vehicle may not restart the first time you try to restart and may take one additional attempt. W ARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury . Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any co[...]

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 40A — — Orange Green Green 50A — — Red Red Red 60A — — Blue Y ellow Y ellow 70A — — T an — Brown 80A — — Natural Black Black Passenger compartment fuse panel The fuse panel is located under the instrument panel to the left of the st[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Components 1 30A Right rear window 2 15A Not used (spare) 3 15A Driver seat control/lumbar 4 30A Right front window 5 10A Brake-shift interlock (BSI) 6 20A T urn signals, hazards 7 10A Low beam headlamps (left) 8 10A Low beam headlamps (right) 9 15A Courtesy lamps 10 15A [...]

Fuse/Relay Location Fuse Amp Rating Protected Components 28 5A Not used (spare) 29 5A Instrument panel cluster (run/start) 30 5A Not used (spare) 31 10A Auto high beam controller , Heads-up display 32 10A Restraint control module 33 10A Adaptive lighting module 34 5A AdvanceT rac 威 , Adaptive cruise control module, Electronic power assist steerin[...]

W ARNING: Always disconnect the battery before servicing high current fuses. W ARNING: T o reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Sp[...]

Fuse/Relay Location Fuse Amp Rating Protected Components 7 — Not used 8 30A** Moon roof 9 40A** Anti-lock brake system (ABS) pump 10 30A** Starter relay 11 30A** Powertrain control module (PCM) relay 12 20A** ABS valve 13 15A* Adapt cruise 14 10A* Brake on/off switch 15 15A* Auto high beam relay 16 20A* Left high intensity discharge (HID) headlam[...]

Fuse/Relay Location Fuse Amp Rating Protected Components 33 40A** Intelligent access (IA) run/start relay 34 — Not used 35 40A** Front A/C blower motor 36 20A* Passenger compartment fuse panel run/start 37 10A* PCM run/start 38 5A* Delayed accessory 39 Diode Fuel pump diode (3.7L V6 engine) 40 Diode One-touch integrated start (OTIS) diode 41 G8V [...]

Fuse/Relay Location Fuse Amp Rating Protected Components 59 — Not used 60 — Not used 61 — Not used 62 — Not used 63 Half ISO relay Run/start relay 64 Half ISO relay PCM relay 65 — Not used 66 — Not used * Mini Fuse **Cartridge Fuse CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradual[...]

Dissimilar spare tire/wheel information W ARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only . This means that if you need to use it, you should replace it as soon as possible with a road tire/[...]

3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a [...]

Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate hazard flashers. 2. Place gearshift lever in P (Park) and turn engine off. Removing the spare tire and jack 1. Lift the trunk cargo cover , and remove the wing nut that secures the spare tire by turning it counterclockwise. 2. Lift and remove the spare [...]

Tire change procedure W ARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park). W ARNING: T o help prevent the vehicle from moving when you change a tire, be sure to place the transmission in P (Park), set the parking brake [...]

3. Align the slot on top of the jack with the sheet metal flange indicated by the jack locator triangle next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground. Note: DO NOT LIFT ON THE PLASTIC MOLDING, as this could damage molding. ONL Y LIFT ON THE SHEET MET AL NOTCH. W ARNING: T o lessen th[...]

Stowing the tire and jack 1. Fully collapse the jack, fold the lug wrench socket into the handle and place the jack and wrench into the felt bag as shown. Place the extension bolt into the external pocket of the felt bag. T ake care to position the jack as shown to ensure that the locating holes in the jack base can be placed on the locating tabs o[...]

If you are stowing the flat tire: 1. Remove the extension bolt from the exterior pocket of the felt bag. 2. Install the jack as shown in Step 4 under Stowing the tire and jack. 3. Screw the extension bolt onto the threaded stud of the jack retention bracket. 4. W ith the temporary spare tire on the vehicle, place the flat tire in the spare tire wel[...]

Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger . DO NOT ap[...]

Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning proce[...]

1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable [...]

Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery . 1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper cable on the negative (-) terminal of the booster vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s bat[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not a[...]

If the vehicle is towed by other means or incorrectly , vehicle damage may occur . Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle. Emergency towing In case of a roadside emergency with a disabled vehicle ([...]

GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certai[...]

In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-[...]

In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-step procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program. The BBB A[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If your vehicle must be serviced while you are traveling or living in Asia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, Central America, the Caribbean, and Israel, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: FORD MOTOR COMP ANY FORD EXPORT OPERA TIONS 1555 Fairlane Drive Fairlane Business P[...]

Customers in the U.S. should call 1-800-392-3673. ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or to order a free publication catalog, call toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Inco[...]

T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1–888–327–4236 (TTY : 1–800–424–9153); go to http://www.safercar .gov; or write to: Administrator 1200 New Jersey A venue, Southeast W ashington, D.C. 20590 Y ou can also obtain other information about motor vehicle safety from http://www.safercar .gov. REPORTING S[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft 威 Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • [...]

W AXING • W ash the vehicle first. • Use a quality wax that does not contain abrasives. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the [...]

• Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo (CXC-66-A). • Never wash or rinse the engine while it is hot or running; water [...]

3.5L V6 ECOBOOST ENGINE PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft 威 Detail W ash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and T ar Remover (ZC-42). WINDOWS AND WIPER BLAD[...]

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft 威 Premium W indshield W asher Concentrate (ZC-32-A) in the U.S., or Premium Quality W indshield W asher Fluid [CXC-37-(A, B, D, or F)] in Canada, available from your authorized dealer . This washer fluid contains special solution in addition to alcohol which helps [...]

If a staining liquid like coffee/juice has been spilled on the instrument panel or on interior trim surfaces, clean as follows: 1. W ipe up spilled liquid using a clean, white, cotton cloth. 2. W ipe the surface with a damp, clean, white cotton cloth. For more thorough cleaning, use a mild soap and water solution. If the spot cannot be completely c[...]

LEATHER SEATS (IF EQUIPPED, EXCEPT FOR THE KING RANCH 姞 EDITION) For King Ranch 威 leather seats, refer to a separate section in this chapter . • Clean spills and stains as quickly as possible. • For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a mild soap and water solution. I[...]

Scratches Natural Markings - Because the leather in the seat comes from genuine steer hides, there will be evidence of naturally occurring markings, such as small scars. These markings give character to the seating covers and should be considered as proof of a genuine leather product. In order to lessen the appearance of certain scratches and other[...]

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Eac[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide to find out which parts and services are covered. Use only r[...]

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located at the bottom of the instrument panel near the steering column. 2. Go to the front of the vehicle and release the auxiliary latch using the handle that is located under the front passenger side of the hood. 3. Lift the hood until the lift cylinders hold it open. Maintenanc[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.7L V6 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap 10. W indshield washer fluid reservoir Maintenance[...]

3.5L V6 EcoBoost™ engine 1. Engine coolant reservoir 2. Brake fluid reservoir 3. Battery 4. Power distribution box 5. Air filter assembly 6. Automatic transmission fluid dipstick (out of view) 7. Engine oil dipstick 8. Engine oil filler cap 9. W indshield washer fluid reservoir 9 1 2 3 4 6 5 8 7 Maintenance and Specifications 299 201 1 MKS (mks) [...]

Engine shield Some vehicles may be equipped with an aero-shield under the engine. This shield needs to be removed for service, including oil and filter changes. It is secured with four quick release fasteners. WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . [...]

CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be impr[...]

5. Locate and carefully remove the engine oil level dipstick. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. ?[...]

• Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer . 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this [...]

current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. T o protect your engine and engine’ s warranty , use Motorcraft 威 SAE 5W -20 or an equivalent SAE 5W -20 oil meeting Ford sp[...]

T o protect your engine and engine’ s warranty , use Motorcraft 威 SAE 5W -30 or an equivalent SAE 5W -30 oil meeting Ford specification WSS-M2C929-A. Refer to Maintenance product specifications and capacities later in this section for more information. Do not use supplemental engine oil additives, cleaners or other engine treatments. They are u[...]

Note: Electrical or electronic accessories or components added to the vehicle by the dealer or the owner may adversely affect battery performance and durability . W ARNING: Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working[...]

6. Release the parking brake. W ith your foot on the brake pedal and with the A/C on, put the vehicle in D (Drive) and allow the engine to idle for at least one minute. 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to relearn the idle and fuel trim strategy . • If you do no[...]

• Protection against rust and other forms of corrosion. • Proper function of calibrated gauges. When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the FULL COLD level, or within the COLD FILL or MIN / MAX range as listed on the engine coolant reservoir (depending upon applicatio[...]

W ARNING: Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. DO NOT MIX recycled coolant and new (unused) coolant together i[...]

Add the proper mixture of coolant and water to the cooling system by following these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (a translucent plastic bottle). Slowly turn cap counterclockwise (left) until pressure be[...]

Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely cold climates (less than –34°F [–36°C]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • A coolant concentration of 60% will pro[...]

How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The coolant temperature warning light will illuminate. • The service engine soon indicator will illuminate. If the engine reaches a preset over -temperature condition, the engine will automatically switch to [...]

W ARNING: Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to a service facility . Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to a service facility as soon as possible. FUEL FILTER Y our vehicle is equipped [...]

• Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury . If fuel is swallowed, call a physician immediately , even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • A void inhaling fuel vapors. Inhaling t[...]

Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking mater[...]

4. After you are done pumping fuel, wait about five seconds before slowly removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank to the point that the fuel is able to bypass the fuel fil[...]

Octane recommendations 3.7L V6 engine Y our vehicle will run normally on 87 octane regular fuel. Premium fuel will provide improved performance. 3.5L V6 EcoBoost™ engine Y our vehicle is designed to run on regular fuel with an octane rating of 87 or higher . For best overall performance, premium fuel with an octane rating of 91 or higher is recom[...]

Cleaner air Ford endorses the use of reformulated “cleaner -burning” gasolines to improve air quality . Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from off to on several times after refueling to al[...]

1. After lifting the trunk cargo cover , locate the white plastic funnel. It is attached to the rear , lower edge of the spare tire compartment. 2. Slowly insert the funnel into the Easy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container . 4. When done, clean the funnel or properly dispose of it. Extra funnels can be pur[...]

The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty . Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty . The amount of usable fu[...]

Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’ s fuel economy under current driving conditions. Additionally , keeping records during summer and winter will show how temperature impacts fuel economy . In general, lower temperatures give lower fuel econo[...]

• Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0[...]

If other than Ford, Motorcraft 威 or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability . W ARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground co[...]

2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly . 3. The fuel fill inlet may not have been properly closed. See Easy Fuel™ “no cap” fuel system in this chapter . 4. Driving through deep water—the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good qu[...]

The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving cycle consisting of mixed city and highway driving may be performed: 15 minutes of steady driving on an expressway/highway followed by 20 minutes of stop[...]

BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; se[...]

5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. (For vehicles with the EcoBoost™ engine, move the air filter assembly aside to access the transmission dipstick). W ARNING: Use gloves when moving the a[...]

C. Remove the bolt cover (if equipped). D. Remove two bolts that attach the air filter assembly to the front of the vehicle (2). E. Loosen the clamp holding the air filter assembly to the rubber hose (1). F . Remove the harness retaining clip by pulling up (3). Do not disconnect the sensor (4). G. W ithout disconnecting the sensor (4), pull the air[...]

W ARNING: Do not run engine with the air filter disconnected. Start the engine and continue with Step 6. 6. Install the dipstick making sure it is fully seated in the filler tube by turning it to the locked position. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature. Low[...]

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Maintenance product specifications and capacities section in this chapter . Use of a non-approved automatic transmission fluid may cause internal transmission compone[...]

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter element listed. Refer to Motorcraft 威 part numbers in this chapter . W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries do not start your [...]

4. W ipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing. 5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover . This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 6. Replace the a[...]

• T ouch-up raw or primed metal to prevent rust. • Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration. Re-wax as necessary when the vehicle is washed. See the Cleaning chapter for more information. • Lubricate all hood, door and trunk lid hinges, and latches with a light grade oil. See the Cleaning c[...]

Brakes • Make sure brakes and parking brake are fully released. T ires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle are covered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricate working parts and prevent corrosion. Removing veh[...]

MOTORCRAFT PART NUMBERS Component 3.7L V6 Engine 3.5L V6 EcoBoost Engine Air filter element F A-1884 F A-1884 Battery BXT -65-650 BXT -65-650 Oil filter FL-500-S FL-500-S Spark plugs SP-411 1 SP-512-A 1 1 Refer to scheduled maintenance information for the appropriate intervals for changing the spark plugs. Replace the spark plugs with ones that mee[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Items Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Brake fluid Between MAX and MIN on reservoir Motorcraft 威 High Performance DOT 3 Motor V ehicle Brake Fluid PM-1-C / WSS-M6C62-A or WSS-M6C65-A1 Door latch, hood latch, auxiliary hood latch, seat tracks, trunk and li[...]

Items Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Engine oil 5.5 quarts (5.2L) (3.7L V6 engine) • Motorcraft 威 SAE 5W -20 Premium Synthetic Blend Motor Oil (US) • Motorcraft 威 SAE 5W -20 Full Synthetic Motor Oil (US) • Motorcraft 威 SAE 5W -20 Super Premium Motor Oil (Canada) • Motorcraft 威 SAE 5W -20 [...]

Items Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Engine coolant 11.1 quarts (10.5L) (3.7L engine) 6 • Motorcraft 威 Specialty Green Engine Coolant 4 • VC-10-A2 (US) • CVC-10-A (Canada) / WSS-M97B55-A • Motorcraft 威 Specialty Orange Engine Coolant (US) • Motorcraft 威 Specialty Orange Engine Coolant (Ca[...]

Items Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Fuel tank 19.0 gallons (71.9L) —— 1 Approximate dry fill capacity . Actual amount may vary during fluid changes. 2 Automatic transmissions that require MERCON 威 L V should only use MERCON 威 L V fluid. Refer to scheduled maintenance information to determine the[...]

ENGINE DATA Engine 3.7L V6 engine 3.5L V6 EcoBoost engine Cubic inches 226 214 Fuel See Octane recommendations earlier in this chapter . See Octane recommendations earlier in this chapter . Firing order 1–4–2–5–3–6 1–4–2–5–3–6 Spark plug gap 0.052–0.056 inch (1.32–1.42 mm) 0.033–0.037 inch (.84– .94 mm) Ignition system C[...]

3.5L V6 EcoBoost engine IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is[...]

V ehicle identification number (VIN) The vehicle identification number is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number . The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross [...]

T RANSMISSION CODE DESIGNATIONS Y ou can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents. Description Code 6-speed automatic transmission (6F50) J 6-speed automatic transmission (with EcoBoost) (6F55) C Maintenance and Specifications 343 201 1 MKS (mks) Own[...]

LINCOLN CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Lincoln Custom Accessories are available for your vehicle through your local Lincoln or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of y[...]

Peace of mind • Remote start • V ehicle tracking and recovery* • Wheel locks • Protective seat covers* • W indshield wiper shaker* • Locking fuel plug for capless fuel system *Ford Licensed Accessories (FLA) are warranted by the accessory manufacturer’ s warranty . Ford Licensed Accessories are fully designed and developed by the acce[...]

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage. Up to 500+ Covered V ehicle Compo[...]

Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. W ith Ford ESP , you minimize your risk for unexpected repair bills and rising repair costs. A void the rising cost of properly maintaining your vehicle! Ford ESP also offers a Premium Maintenance P[...]

Ford Extended Service Plan 348 201 1 MKS (mks) Owners Guide, 1st Printing USA (fus)[...]

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) Y ou can get more protection for your vehicle by purchasing a Ford Extended Service Plan (ESP). Ford ESP is the only service contract backed by Ford Motor Company . Depending on the plan you purchase, Ford ESP provides benefits such as: • Rental reimbursement • Coverage for certain maintenance and w[...]

GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle. Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it. It is y[...]

different specifications and performance features. That’ s why it’ s important to rely upon your Ford or Lincoln Mercury dealership to properly diagnose and repair your vehicle. Ford Motor Company has recommended maintenance intervals for various parts and component systems based upon engineering testing. Ford Motor Company relies upon this tes[...]

Convenience Many dealerships have extended evening and Saturday hours to make your service visit more convenient. How’ s that for quality service? Factory-trained technicians Ford and Lincoln Mercury service technicians participate in extensive factory-sponsored certification training to help them become experts on the operation of your vehicle. [...]

Multi-point inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly . This can help identify potential issues and prevent major problems. Ford Motor Company recommends the following multi-point inspection be performed at every scheduled maintenance interval to help ensure your ve[...]

Be sure to ask your Ford or Lincoln Mercury dealership service advisor or technician about the multi-point vehicle inspection. It’ s a comprehensive way to perform a thorough inspection of your vehicle. It’ s your checklist that gives you immediate feedback on the overall condition of your vehicle. Y ou’ll know what’ s been checked, what’[...]

Scheduled Maintenance Guide 355 201 1 MKS (mks) Owners Guide, 1st Printing USA (fus)[...]

NORMAL SCHEDULED MAINTENANCE AND LOG For your convenience, your vehicle is equipped with a message center which determines the proper oil change service interval. Y ou should perform the engine oil change as indicated by the instrument cluster message center . The message center will display ENGINE OIL CHANGE SOON or OIL CHANGE REQUIRED to indicate[...]

Oil Change Service Interval* 1 2 3 456789 1 0 Change engine oil and filter • ••••••••• Rotate tires, inspect tire wear and measure tread depth • ••••••••• Inspect the wheels and related components for abnormal noise, wear , looseness or drag • ••••••••• Perform multi-point inspection (reco[...]

Oil Change Service Interval* 11 12 13 14 15 Change engine oil and filter • •••• Rotate tires, inspect tire wear and measure tread depth • •••• Inspect the wheels and related components for abnormal noise, wear , looseness or drag • •••• Perform multi-point inspection (recommended) • •••• Inspect automatic tra[...]

Perform the services noted in the following table at the specified time/mileage (km) period either within 3,000 miles (5,000 km) of the OIL CHANGE REQUIRED message appearing in the message center or when the time/mileage (km) reading indicates service is due. Example #1: The OIL CHANGE REQUIRED message comes on at 28,751 miles (46,270 km); perform [...]

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H [...]

D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : [...]

D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : [...]

SPECIAL OPERATING CONDITIONS If you operate your Ford/Lincoln/Mercury vehicle primarily in one of the more demanding Special Operating Conditions listed below , you will need to have some items maintained more frequently . If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additional maintenance[...]

Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery , taxi, patrol car or livery As required – Change engine oil and replace oil filter as indicated by message center and perform ser vices as listed in the Normal Scheduled Maintenance chart (except Fiesta). Every 300 hours of engine operation* [...]

Operating in dusty conditions such as unpaved or dusty roads Every 5,000 miles (8,000 km) – Rotate tires, inspect tires for wear and measure tread depth. – Inspect the wheels and related components for abnormal noise, wear , looseness or drag. Every 5,000 miles (8,000 km) or 6 months – Change engine oil and replace oil filter . Every 30,000 m[...]

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : [...]

D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : [...]

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. They are listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic lubricant and light duty trucks equipped with Ford-design axles are lubricated for life. These lubricants are not to be checked or changed unless a lea[...]

COOLANT CHANGE RECORD Engine coolant ❑ 6 years or 100,000 miles (160,000 km) - change coolant (whichever comes first). ❑ After initial change - change coolant every 3 years or 50,000 miles (80,000 km). Scheduled Maintenance Guide 369 201 1 MKS (mks) Owners Guide, 1st Printing USA (fus)[...]

Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H[...]

A Accessory delay .......................... 77 Active Park Assist .....................240 Adaptive Cruise Control ............. 81 AdvanceT rac .............................. 225 Air cleaner filter ...............331, 335 Air conditioning ....................48, 51 Airbag supplemental restraint system ................ 153–154, 162, 164 and chil[...]

in rear seat .............................. 173 LA TCH ..................................... 176 recommendations ................... 170 Child safety seats - booster seats ........................................... 181 Cleaning your vehicle engine compartment ..............288 instrument panel .................... 291 interior ....................[...]

cleaning ................................... 288 coolant ..................................... 307 fail-safe cooling ....................... 311 idle speed control ................... 305 lubrication specifications ....... 336 refill capacities ........................ 336 service points .................. 298–299 Engine block heater ............[...]

Illuminated visor mirror ............. 71 Infant seats (see Safety seats) ..................... 172 Inspection/maintenance (I/M) testing ........................................ 324 Instrument panel cleaning ................................... 291 cluster ........................................ 12 lighting up panel and interior ...................[...]

Oil (see Engine oil) .................. 301 P Parental MyKey programming ............................. 100 Park Assist ................................ 240 Parking brake ............................224 Parts (see Motorcraft 威 parts) ........... 335 Passenger Occupant Classification Sensor ................. 141 Power distribution box (see Fuses) .[...]

climate control ............ 48, 51, 132 Cooled ..................................... 131 easy access/easyout feature .. 135 front seats ............................... 131 heated ...................................... 138 Heated and Cooled .................131 memory seat ................... 115, 134 SecuriCode keyless entry system ...............[...]

V ehicle loading ..........................206 V entilating your vehicle ........... 220 W W arning lights (see Lights) ....... 12 W asher fluid .............................. 300 W ater , Driving through ............. 255 W indows power ......................................... 75 W indshield washer fluid and wipers ...............................[...]