Little Wonder TSS-20 инструкция обслуживания

Schiller -Pfeiffer , Inc. 1028 Street Road • Southampton, P A 18966 T elephone: 1-800-366-6268 TRS-20 TURF RAKE (Serial No. 00127 & UP) TSS-20 TURF SEEDER (Serial No. 00143 & UP) OPERA TORS / P AR TS MANUAL[...]

2 THANK YOU Thank you for pur chasing a CLASSEN TRS-20/ TSS-20. READ THIS MANUAL Read this manual carefully in its entir ety . It contains assembly , operating, maintenance, adjustment instructions and a parts list for your TRS-20/TSS-20. By following the operating and maintenance instructions you will prolong the life of your equipment and maintai[...]

3 PRE-DELIVER Y CHECK LIST CHECK THE FOLLOWING BEFORE YOU DELIVER THE TRS-20/TSS-20 TO THE CUSTOMER. 1. Guards and shields fastened in place. 2. Decals fastened and legible. 3. Gas lever on engine turned on. 4. All lubrication points greased. 5. Air cleaner . 6. T ouch up scratches. 7. Add engine oil (refer to Engine manual) 8. Add fuel, start engi[...]

4 SAFETY PRECAUTIONS TRAINING 1. Regard the unit as a piece of power equipment and teach this regar d to all who operate this unit. 2. Read the instructions carefully . Be familiar with the controls and the pr oper use of the equipment. 3. Never allow children, teenagers or people unfamiliar with these instructions to use this piece of equipment. 4[...]

5 OPERA TION PREP ARA TION 1. Carefully r ead this manual and operate TRS-20/TSS-20 correctly . 2. Always check machine on level ground. 3. V isually check all moving parts and all fasteners, if loose or broken, tighten or replace. Check for br oken or bent blades, replace if necessary . 4. Lubricate all fittings after every four hours of using mac[...]

6 OPTIONAL BLADE ASSEMBLIES CHANGING BLADE ASSEMBLIES W ithin minutes your machine can be converted to a turf rake, turf seeder or tur f slicer by pur chasing the optional blade assemblies available complete with side plates, bearings and drive pulley . Changing the blade assembly can be done quickly as described below . 1. Set unit up on block all[...]

7 Seeding/Multipurpose Height The seeding/multipurpose blades are used for cutting grooves for over -seeding and can also be used for verticutting grasses. T o set the height properly place unit on the lawn sur face and adjust the wheel height up (see Fig. 4 ). Adjusting the wheel height up lowers the blades. Seeding The proper height setting for o[...]

8 GENERAL MAINTENANCE TO KEEP THE TRS-20/TSS-20 IN GOOD OPERA TING CONDITION, PERFORM THE FOLLOWING: • When replacement par ts are requir ed, use genuine Classen parts or parts with equivalent characteristics including type, strength, and material. Failur e to do so may result in pr oduct malfunction and possible injury to the operator and/or bys[...]

9 CARE FOR HYDRAULIC SYSTEM T o keep the hydraulic system in working or der , there ar e a few steps needed to take place. If synthetic oil were used we would suggest a full synthetic oil such as Mobil 1 15W50, Quaker State Full Synthetic 5W50 , or a similar oil. Oil viscosity is very important to transmission life. For optimum performance the oil [...]

10 P AR TS MAIN FRAME ASSEMBL Y[...]

11 P AR TS SELF PROPELLED ASSEMBL Y[...]

12 P AR TS HANDLE ASSEMBL Y[...]

13 SEEDER/MUL TIPURPOSE BLADE ASSEMBL Y SLICER BLADE ASSEMBL Y (OPTIONAL) QTY/PER KEY P ART NO . MACHINE DESCRIPTION 1 700025 1 Shaft w/ Blade Holders, Multipurpose 2 100310 26 Blade w/ 15/16” Holes, Multipurpose 3 500216 52 Bolt, 5/16-18 x 314 Grade 8 4 500217 52 Nut, 5/16-18 T ap Lock 5 600030 1 Shaft/Blades Sub-Assembly , Multipurpose 6 900026[...]

14 QTY/PER KEY P ART NO . MACHINE DESCRIPTION 1 500068 8 1/4” NYLOC NUT 2 100140 1 GAUGE w/ BOL T & WING NUT 3 500089 2 1/4” x 1-1/2” BOL T 4 100142 1 CONTROL LEVER GRIP 5 100141 1 CABLE CONTROL LEVER 6 500118 3 1/4” x 1-3/4” BOL T 7 100139 1 CONTROL CABLE (NOT SHOWN) 8 100127 1 FRICTION WASHER 9 100229 3 #8 x 3/4” BLACK SCREW 10 10[...]

15 SEEDER TIRE SCRAPE INST ALLA TION SEED BOX INST ALLA TION For shipping purposes only , the seed box assembly is a ttached to machine improperly . T o set your machine correctly for opera tion, remove hairpin c lip (A) from upper connecting rod (B). Slide upper rod out, allowing “A shaped” stabilizing bracket (C) on seed box to sit over lower[...]

16 SAFETY DECALS QTY/PER KEY P ART NO . MACHINE DESCRIPTION 1 100074 2 Decal, “Classen” 2 100060 1 Decal, “CAUTION - Muffler and Shields May Exceed 150°” 3 100340 1 Decal, “TRS-20” (T urf Rake only) 4 100071 1 Decal, “Bail Engagement” 5 100061 1 Decal, “CAUTION - Operating Instructions” QTY/PER KEY P ART NO . MACHINE DESCRIPTIO[...]

17 NOTES[...]

ONE YEAR LIMITED W ARRANTY Effective January 1, 1994 For the period of one year from the date of pur chase, CLASSEN MFG., INC. will r epair or replace for the original pur chaser (90 days if used for rental purposes) fr ee of charge, any part or par ts found upon the examination of our factory authorized service station, or by the factory in Norfol[...]