Makita 3621 инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Router MODEL 3621 003251 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to[...]

5 9. Before using the tool on an actual w ork- piece, let it run for a while. Watc h for vibration or wobb ling that could indicate improperl y installed bit. 10. Be careful of the bit rotating direction and the feed direction. 11 . Do not leave the tool running. Operate the tool only when hand-held. 12. Alwa ys switch off and wait for the bit to c[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Adjusting the depth of cut Place the tool on a flat surf ace. Loosen the screw securing the stopper pole. Loosen the lock le ver and lo wer the tool body until the bit just touches the flat surf ace.[...]

7 deep with an 8 mm (5/16 ” ) diameter bit or more than 5 mm (3/16 ” ) deep with a 20 mm (13/16 ” ) diameter bit, make se ver al passes with progressively deeper bit settings. Stopper bloc k The stopper bloc k has three adjusting hex bolts which raise or lower 0.8 mm (about 1/32 ” ) per turn. Y ou can easily obtain three diff erent depths o[...]

8 Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s witch tr igger actuates properly and retur ns to the “ OFF ” position when released. T o star t the tool, simply pull the switch trigger . Release the s witch tr igger to stop . ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and un[...]

9 NO TE: • Moving the tool f orward too f ast may cause a poor quality of cut, or damage to the bit or motor . Moving the tool f orward too slowly ma y burn and mar the cut. The proper fe ed rate will depend on the bit size, the kind of workpiece and depth of cut. Before beginning the cut on the actual workpiece, it is advisable to mak e a sample[...]

10 When cutting, mov e the tool with the straight guide flush with the side of the workpiece. If the distance (A) between the side of the workpiece and the cutting position is too wide for the straight guide, or if the side of the w or kpiece is not straight, the straight guide cannot be used. In this case , firmly clamp a straight board to the wor[...]

11 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. T o maintain product SAFETY and RELIABILITY , repairs, car- bon brush inspection and replacement, any other mainte- nance or adjustment should be perf or med by Makita A uthor ized or F actor y Ser vice C[...]

Memo 12[...]

13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]