Makita 4323 инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Jig Sa w MODEL 4323 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to[...]

5 8. Make sure the blade is not contacting the workpiece bef ore the switch is turned on. 9. Keep hands awa y from moving parts. 10. Do not leave the tool running. Operate the tool only when hand-held. 11 . Alwa ys switch off and wait for the blade to come to a complete stop before remo ving the blade from the w orkpiece. 12. Do not touch the blade[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s witch tr igger actuates properly and retur ns to the “ OFF ” position when released. • Switch can be lo[...]

7 CA UTION: • If the tool is operated continuously at lo w speeds for a long time, the motor will get o verloaded and heated up. • The speed adjusting dial can be turned only as far as 6 and back to 1. Do not f orce it past 6 or 1, or the speed adjusting function ma y no longer work . ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is swi[...]

8 Hex wrench stora ge When not in use, store the he x wrench as shown in the figure to keep it from being lost. Adjusting roller Loosen the bolt on the back of the base with the he x wrench. Mov e the retainer so that the roller contacts the blade lightly . Then tighten the bolt to secure the base and the retainer . NO TE: • Occasionally lubricat[...]

9 OPERA TION CA UTION: • Alwa ys hold the base flush with the workpiece. F ailure to do so ma y cause blade breakage, resulting in a serious injur y . • Advance the tool v er y slo wly when cutting cur ves or scrolling. Fo rcing the tool may cause a slanted cutting surf ace and blade breakage. T ur n the tool on without the blade making an y co[...]

10 Tilt the base until the desired be vel angle is obtained. The edge of the motor housing indicates the be vel angle by g rad- uations. Then tighten the bolt to secure the base . Front flush cuts Loosen the bolt on the back of the base with the he x wrench and slide the base all the wa y back. Then tighten the bolt to secure the base. Cutouts Cuto[...]

11 (4) Complete the cut in the normal manner. Finishing edges T o tr im edges or mak e dimensional adjustments, run the blade lightly along the cut edges . Metal cutting Alwa ys use a suitable coolant (cutting oil) when cutting metal. F ailure to do so will cause significant blade w ear . The underside of the workpiece can be greased instead of usi[...]

12 T o install, inser t the r ip f ence into the rectangular hole on the side of the base with the f ence guide facing down. Slide the rip fence to the desired cutting width position, then tighten the bolt to secure it. 2. Circular cuts When cutting circles or arcs of 170 mm (6 - 11/16 ” ) or less in radius, install the rip f ence as follo ws. In[...]

13 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose. If you need an y assistance for more details regarding [...]

Memo 14[...]

Memo 15[...]

Memo 16[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]