Makita 5092DW инструкция обслуживания

Cordless Circular Saw Blade diameter 85 mm (3-3/8”) MODEL 5092D 85 mm (3-3/8”) MODEL 5092DW With Fast Charger weight Cutting depth No load speed Overall (RPM) length 9ou 45” INSTRUCTION MANUAL Battery Cartridge 1210 Uses 12 V / 9.6 V Battery Model DC1290 Fast Charger SPEC IF I CAT1 0 N S Model 5092D Vol taae IrlDUt Output I Charsina time I I [...]

I M PORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invite [...]

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cord[...]

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE I. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) AWG Size of Cord contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) produc[...]

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50°F) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batt[...]

ADDITIONAL SAFETY RULES FOR CORDLESS CIRCULAR SAW 1. Be aware that this tool is always in an operating condition, because it does 2. Wear hearing protection. 3. Keep Guards In Place and In Working Order. not have to be plugged into an electrical outlet. Never wedge or tie lower guard open. Check operation of lower guard before each use. Don't [...]

NEVER place your hand or fingers behind the saw. If kickback occurs, the saw could easily jump backwards over your hand, possibly causing severe injury. Fig. 3 IO. Lower Guard. Raise lower guard with the retracting handle. 11. Adjustments. Before cutting be sure depth and bevel adjustments are tight. 12. Use Only Correct Blades In Mounting. Don’t[...]

15. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way. If the workpiece is short or small, clamp it down. DON'T TRY TO HOLD SHORT PIECE[...]

Installing or removing the battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. 1200 / 1210 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. *To insert the battery cartridge, align the tongue on the battery [...]

CAUTION : .The fast charger Model DC1290 is specifically designed to charge only Makita battery cartridges. Never use it for other purposes or for other manufacturer’s batteries. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, the charging light may not come on. If this occurs, jus[...]

To install the blade, follow the removal procedure in reverse. BE SURE TO TIGHTEN THE BOLT SE CU RELY. Fig. 1' CAUTION: 0 Be sure the blade is installed with teeth pointing up at the front of the tool. 0 Use only the Makita hex wrench to install or remove the blade. Hex wrench storage When not in use, the hex wrench can be conveniently stored.[...]

Adjusting the depth of cut Loosen the screw on the depth guide and move the base up or down. You can read the depth of cut by aligning the top of the notch in the depth guide with the graduations on its right side. (Note: This can be done for 0" bevel cutting only.) At the desired depth of cut, secure the base by tightening the screw. Base Scr[...]

Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0" engraved on it with your cutting line on the workpiece. For 45" bevel cuts, align the edge with 45" engraved on it with your cutting line. Switch action To prevent the trigger from being acciden- tally pulled, a lock-off le[...]

Guide rule The handy guide rule allows you to do extra-accurate straight cuts. Simply slide the guide rule up snugly against the side of the workpiece and secure it in position with the clamp screw on the front of the base. It also makes repeated cuts of uni- form width possible. Clamp screw 14[...]

MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting or perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 15[...]

ACCESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 79261 1-2 721005-A 0 Battery cartridge 1210 [...]

Sei, 19-'95 US 85 mm (3-3/8") CORDLESS CIRCULAR SAW Model 5092D Note: The switch and other part configurations may differ from country to country. 17[...]

MODEL 5092D IFOM ,,I:, DESCRIPTION sev-19- 95 us ILLM AtD DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 6 17 18 1 4 20 21 22 21 24 25 1 1 1 1 1 1 2 1 1 1 1 6 1 1 1 1 1 1 1 1 1 MACHINE ~ 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 41 48 49 50 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 Slop Ring E 4 iex Nu1 M5 3all Beari[...]

Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. 1 Ni-Cd 1 To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or D[...]