Makita 6071D инструкция обслуживания

Cordless Driver Drill Cdpacitics - Stcel Wood Wood screw Equipped with Electric Brake MODEL 6071D MODEL 6071DW With Fast Charger MODEL 607lDWK No load speed Dimensions IL x W x HI Net weight With Fast Charger and Carrying Case INSTRUCTION MANUAL SPEC IF I CAT IONS 10 11111, 4 5 mm x 20 mini 1 ~~ 6oo R,m,n I 220 mm x 49 mm x 215 mm 115kg 13 a"![...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. KEEP WORK AREA CLEAN. Cluttered areas and benches invite inju[...]

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext[...]

IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) 25 50 100 AWG Size of Cord 18 18 18 1. SAVE THESE INSTRUCTIONS - This manual 150 16 9. Do not operate charger with damaged cord or plug - replace them im- mediately. IO. Do not operate charger if it has received a sharp blow, been dropped, or other- wise damaged in any way; take it to a qualified [...]

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batte[...]

Installing or removing battery cartridge 0Always switch off the tool before inser- tion or removal of the battery cartridge. .To remove the battery cartridqe, pull out j the set plate on the bottom if the tool and grasp both sides of the cartridge while withdrawing it from the barrel. .To insert the battery cartridge, align the tongue on the batter[...]

Nominal diameter (mm) Bit No. Wood screw 2.1 - 2.7 (3/32" - 1/8") Selecting correct Phillips bit Use the chart to determine the best size driver bit for the size of screw that you wish to use. No. 2 3.1 - 4.5 (118"- 3/16") Selecting slotted bit Use a slotted bit that properly fits the screw slot. Use of a bit that is too small w[...]

to stop. CAUTION : Before inserting t..e battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the revers- ing switch to the right for clockwise rota-[...]

Bubble level This tool is equipeed with a bubble level to aid in holding the tool horizontally. Simply center the bubble in the sight window. 4.5 (11/64") Bubble level 7 2.9 - 3.2 (7/64 - 1 /8") Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increas[...]

Drilling operation 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to[...]

MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 11[...]

ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons, The accessories or attachments should be used only in the proper and intended manner. Bits Fast charger Model DC7100 Part No. 113109[...]

0 Battery holster Holster holds extra battery Part No. 823033-3C 0 Steel carrying case Part No. 823087-3 (Steel case) Part No. 181372-3 (Plastic Case) 0 Tool holster has some bits storage space Use holster to carry drill only after removing bit. Part No. 823033-3A Part No. 823033-3E (Genuine holster) 13[...]

10 mm (3/8") CORDLESS DRIVER DRILL Model 6071D Note: The switch and other part configurations may differ from country to country. MODEL 6071D 1 14[...]

MOUEL 6071U Apr 21 86 EN la 11 12 13 14 15 16 17 18 'EM A&, DESCRIPTION I 7 1 1 1 1 1 1 1 I:,'," ,,!& DESCRIPTION Drill Chuck S10 Pan Head Screw M5x18 Gear Plane Bearing 5 Motor Holder 6 Swmh Housing R I Bubble Level Tube Pan Head Screw M4x22 IWilh Wdhherl set Plat0 Houstng L Swrtch Plane Bearing 3 Gear Couplele 13 58 Name Pl[...]

f’ MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every hlakita tool is thoroughly inspected and tested before leaving the factory. It IS warranted to he free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any troubkdevelop during this one-year period, return the COMPLETE tool, fr[...]