Makita 6093DW инструкция обслуживания

Cordless Driver Drill Capacities Steel Wood Wood screw Machine screw 10 mm 18 mm 5.5 mm x 55 mm 6 mm 1318") I1 Jj16"l 17/32" x 2-1j8"l 115164") Equipped with Electric Brake 10 mm (3/8") MODEL 60930 10 mm (3/8") MODEL 6093DW Dimensions Net IL x W x HI 265 mm x 58 mm x 262 mm No load speed weight 1.7 kg High Low 0 ~[...]

IMPORTANT SAFETY IN STRU CTlO N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches i[...]

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext[...]

IMPORTANT SAFETY 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA Battery 7000,[...]

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Do not short the battery cartridge: or ABOVE 4OoC (104OF). receptacle. ([...]

Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge. .To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. 0 To insert the battery cartridge, align the tongue on the battery cartridge with [...]

0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Installing or removing drill bit or driver bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. To install the bit, place it in the chuck as far as it will go. Tight[...]

Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing swi[...]

Adjusting fastening torque I I The fastening torque can be adjusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the -8- marking. The clutch will slip at varying torque l[...]

NOTE : 0 Use the proper bit for the head of the screw that you wish to use. 0 Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. 0 When driving wood screws, predrill Pilot Nominal diameter of I Recommended size holes to make driving easier and to pre- vent splitting of the workpiece. See th[...]

Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20 -30 seconds before resuming operation. Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. Ni-Cd To recycle a battery: 1. Remove the battery f[...]

MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 12[...]

OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of [...]

Dec 25-'86 EN 10 mm (318") CORDLESS DRIVER DRILL Model 6093D Note: The switch and other part configurations may differ from country to country. 14[...]

MODEL 6093D Dec -25-'86 EN 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 'iM DESCRIPTION 'iM $fD DESCRIPTION 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 10 11 12 13 14 15 16 17 18 19 20 21 22 Pan Head Screw M4x22 lWllh Washer] Pan Head Screw M4x35 IWtth Washer1 Housing Set (With Item 441 Guide Plate cam Plate Pa[...]

I MAKITA LIMED ONE YEAR WARRANTY Warranty Policy t Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freig[...]