Makita 6832 инструкция обслуживания

Auto Feed Screwdriver No load speed (RPM) 0 -- 2,800 Screw strip 4 mm x 25 mm - 57 mm (5132" x 1" ~ 2-114") MODEL 6832 Variable Speed I Reversing Overall length Net weight 372 mm (14-518") 2.0 kg (4.4 Ibs) INSTRUCTION MANUAL[...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT.[...]

Ampere Rating More Not More Than Than 0- 6 6 - 10 10 - 12 12 - 16 3 Total Length of Cord in Feet 0 - 25 26 - 50 51 - 100 101 - 150 AWG 18 16 16 14 18 16 14 12 16 16 14 12 14 12 Not Recommended[...]

VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T[...]

Adjusting the stopper plate (Fig. 1, 2, 3 & 4) There are two kinds of stopper plates; one is for screws 25 mm (1") - 41 mm (1-5/8") long and the other is for screws 40 mm (1-9/16") - 57 mm (2-1/4") long. When the tool is shipped, the former stopper plate is installed on the casing and the latter stopper plate on the feeder b[...]

Adjust the stopper plate in accordance with the screw length as shown in Fig, 3 81 4. If necessary, loosen the bolts which secure the stopper plate. Fig. 3-1 : For screws 25 mm (1") - 28 mm (1-1/8") long Fig. 3-2: For screws 28 mm (1-1/8") - 35 mm (1-3/8") long Fig.3-3: For screws35 mm (1-3/8") -41 mm (1-5/8") long Fig[...]

Setting the slide plate (Fig. 5 & 6) When driving screws 25 mm (I") - 41 mm (1-5/8") long, set the slide plate to the posi- tion shown in Fig. 5. To set the slide plate, press it in the direction of the arrow while depressing the screw in the center of the adjusting knob. Adjusting the driving depth (Fig. 7) Depress the stopper plate [...]

Installing the screw strip (Fig. 8 81 9) Insert the screw strip through the screw guide. Then insert it through the feeder box until the first screw reaches the position next to the driving position. Feeder box Screw strip I Fig. 8 Removing the screw strip (Fig. IO) To remove the screw strip, just pull in the direction of the arrow. it out -Driving[...]

Switch action (Fig. 12) CAUTION : Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool[...]

Driving operation (Fig. 14) Switch on the tool by pressing the trigger and at the same time pushing the lock button. Hold the tool squarely against the workpiece and apply forward pressure to the tool. The screw will be automatically carried to the driving position and driven into the workpiece. Fig. 14 IMP0 RTANT : Do not fire the tool without scr[...]

Extension handle (optional accessory) (Fig. 17) Use of extension handle allows you to drive screws into floors while standing. Fig. 1 11[...]

MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be r[...]

ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Phillips bit 2-132 (5 per pkg.) Part No. A- 1[...]

Mar.-30-'95 US AUTO FEED SCREWDRIVER Model 6832 Note: The switch, noise suppressor and other part configurations may differ from country to country. 14[...]

Mar.-30-'95 US MODEL 6832 ITEM NO. NO. USED DESCRIPTION $tD DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 I1 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 21 28 29 30 31 32 33 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - Slopper Base Box Cover Complete Leaf Spmg Slopper PI" 3 Feeder Box Complete Phillips Bit No 2 132L D[...]

P MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, frei[...]