Makita 6900D инструкция обслуживания

n Capacities Bolt size Square drive Standard bolt High tensile bolt I - Impacts per minute At high speed At low speed 12.7 mm (1/2") MODEL 6900D 12.7 mm (1/2") MODEL 6900DW With Fast Charger M8 - M14 15/16" - 9/16") INSTRUCTION MANUAL ME - M10 15/16" ~ 318") 12 7 mm 11/2"l 2,000 1,500 SPECIFICATIONS No load speed[...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONM[...]

I 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only e[...]

IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To red[...]

ADDITIONAL SAFETY RULES I FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anythiqg to cover or clog the charger vents. 4. Do not short the battery cartridge: or ABOVE 4OoC (104OF). receptacle.[...]

Installing or removing battery cartridge Always switch off the tool before insertion To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it int[...]

e When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely a couple of times. e If you wish to charge two battery cartridges, allow[...]

Reversing switch and speed change switch action Slide the reversing switch to the right for clockwise rotation or to the left for counterclockwise. Slide the speed change switch to the right for high speed (high tightening torque) or to the left for low speed (low tightening torque). Select the speed suitable for your bolt by referring to the figur[...]

Operation The proper tightening torque may differ depending upon the kind or size of the bolt. The relation between tightening torque and tightening time is shown in the figures below. Standard bo1 t kg cm Iff. Ibrl MI4 l9/16'1 at high rpssd Proper lightening lorqua lor M14 l9/16"1 Proper tightening torque lor M12 1112''I MI0 13[...]

Speed Type of bolt Tightening time High High tensile bolt M10 13/8") 3 seconds Low Standard bolt M8 (5/16") 1 second CAUTION : If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Number of tightenings 90 450 10 .. *..:k:: . i'i,[...]

.. : . .. ,.. ... . ..... i:: !,?>. . .. . . . .. , . . .... .. . .. . . , . . ... .. ... . .. .., .. . . .... . . :. :. ,.,.. . +:;.,I. ii ;; . MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY[...]

ACCESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended mannuer. Socket (With pin and 0 ring) 0 ring for soc[...]

... : , . . . . ,. . .. . .. . :.i:.. h:; . .. .. !.? : ' ... f.. ... .. . .. .. ,:: ..:. .. ._._ ... .. . ... ; , 1'. 8, 1 .. .. 'I .;:.$,: . . ,,., ... , , 784208- 1 Phillips bit (Use with bit adapter) 45 (1-3/4") Bit adapter Part No. 134530-0 [With pin (Part No. 256095-3) and 0 ring (Part No. 213370-O)] For driving machine sc[...]

Juna-Ol-'BB US 12.7 mm (1/2") @-- CORDLESS IMPACT WRENCH Model 6900D Note: The switch and other part configurations may differ from country to country. 14 .. .. . . ..[...]

MODEL 69000 $$D DESCRIPTION ';"OM $&, DESCRIPTION June-03-'88 US MACHINE - 1 2 3 4 5 6 7 0 9 10 11 12 13 I4 15 16 17 18 19 - I 1 1 1 1 1 1 I 1 1 1 I 1 I 1 1 1 I 1 - Pan Head Screw M3x14 lWilh Washer1 Switch Pan Head Screw M3.14 lWith Washer1 Compression Spring 2 Hausmp S.1 lWith Item 201 L..l SP" LWa, PI.". 0.anng 4 Gem[...]

I MAKmA LIMITED ONE YEAR WARRANTY Warranty Policy Fvery Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from workanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight[...]