Makita 8413 инструкция обслуживания

Cordless Percussion=Driver Drill Equipped with Electric Brake DZ DWA DWD DWF INSTRUCTION MANUAL - - - Nt-Cd 2 0 AH NI-MH~~H NI-MH 3 o AH-[...]

SPECIFICATIONS Concrete 13 mm f 1 /2 ") 8413D Steel Wood Wood screw Machine screw 13 mm 30 mm 6 mm x 75 mm 6 mm ( 1 /2 ") (1-3/16"1 (1/4" x 3") (1 /4" ) 6 mm 11 /4 " ) No load speed (RPM) Model High 1 Low 38" I lOmmx90mm (3/8" x 3-1/2") I1 /4 " ) Blows per minute Overall length Net weight High [...]

GENERAL SAFETY RULES U’A(l(’J1 (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite ac[...]

Tool Use and Care 12. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 13. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is d[...]

Specific Safety Rules 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator. 2. Be aware that this tool is always in an operating condition, because it does [...]

IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) 25 50 100 AWG Size of Cord 18 18 18 FOR CHARGER & BATTERY CARTRIDGE 150 16 I. SAVE THESE INSTRUCTIONS - This manual 6[...]

USCUOl 1 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power or ABOVE 4OoC (104OF). receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery ter[...]

FUNCTIONAL DESCRIPTION Installing or removing battery cartridge Always switch off the tool before inser- tion or removal of the battery cartridge To remove the battery cartridge, with- draw it from the tool while pressing the buttons on both sides of the cartridge *To insert the battery cartridge, align the tongue on the battery cartridge with the [...]

If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color If this occurs, wait for a while Charging will begin after the battery cartridge cools The battery cartridge will cool faster if you remove[...]

Reversing switch action CAUTION *Always check the direction of rotation before operation *Use the reversing switch only after the tool comes to a complete stop Changing the *When not operating the tool, always set the reversing switch lever to the neutral posi- direction of rotation before the tool stops may damage the tool tion This tool has a rev[...]

Selecting the action mode This tool employs an action mode changing ring Select one of the three modes suit- able for your work needs by using this ring For rotation only, turn the ring so that the arrow on the tool body points toward the anamark on the ring For rotation with hammering, turn the ring so that the arrow points toward the +on the ring[...]

ASSEMBLY Installing or removing driver bit or drill bit CAU TI 0 N : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Turn the sleeve clock- wise to tighten the chuck. To r[...]

Adjustable depth rod s *When driving wood screws, predrill pilot Nominal diameter of holes to make driving easier and to pre- vent splitting of the workpiece. See the chart. woodscrewl"l 3 1 11/8"1 3 5 19/64',) 3 8 15/32") 4 5 (1 1/64"J 4 8 (3/16") 5 1 113/64") 5 5 17/32") 5 8 17/32") 6 1 I1 5/64 "1[...]

Drilling operation First turn the action mode changing ring so that the arrow on the tool body points to the 2 marking The adlusting ring can be aligned in any torque levels for this operation Then proceed as follows *Drilling in wood When drilling in wood best results are obtained with wood drills equipped with a guide screw The guide screw makes [...]

Blow-out bulb I Use the blow-out bulb to clean out the hole Installing set plate For 8413D Always install the set plate when using bat- tery cartridges 1200, 1202 or 1202A. Install the set plate on the tool with the screw provided. 15[...]

MAINTENANCE CAUTION Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance the same time. Use only identical carbon brushes. Replacing carbon brushes Remove and check the carbon brushes reqularlv. Replace when they wear down to Limit mark / the limit mark. Keep the ca[...]

ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Bit Shank Part No 1 diameter I dia Bits 1 Sire I Pa[...]

Wool bonnet Part No. 743401-6 Battery cover Part No. 414938-7 - High capacity battery charger Model DC1801 Battery cartridge 1222 I 1234 I 1235 Battery cartridge 1822 I 1834 I 1935 Plastic carrying case ‘Grip assembly Part No 122575-0 Depth rod Part No. 122576-8 High capacity battery charger Model DC1411 Battery cartridge 1422 I 1434 I 1435 m Saf[...]

MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh[...]