Makita 9564 инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Angle Grinder MODEL 9564 MODEL 9565 004266 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to[...]

5 cracked or dama g ed wheel immediatel y . Run the tool (with guard) at no load f or about a minute, holding tool awa y from others. If wheel is flawed, it will likel y sep- arate during this test. 7. Use only flanges specified for this tool. 8. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock n ut. [...]

6 SYMBOLS USD201-1 The f ollowings show the symbols used f or tool. V ....................... volts A ....................... amperes Hz ..................... her tz ................ alternating current .................... no load speed .................... Class II Construction .../ min or RPM ... rev olutions or reciprocation per minute n ˚[...]

7 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Shaft lock CA UTION: • Ne ver actuate the shaft lock when the spindle is mo ving. The tool ma y be damaged. Press the shaft lock to pre vent spindle rotation when install- ing or removing accessori[...]

8 Installing side grip (handle) CA UTION: • Alwa ys be sure that the side grip is installed securely bef ore operation. Screw the side grip securely on the position of the tool as shown in the figure. Installing or removing wheel guar d CA UTION: • When using a depressed center grinding wheel/Multi- disc, wire wheel brush or cut-off wheel, the [...]

9 Installing or removing abrasive disc (optional accessory) NO TE: • Use sander accessories specified in this manual. These must be purchased separately . Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the loc k nut onto the spindle. T o tighten the lock n ut, press the shaft lock fir mly so that the spindle canno[...]

10 grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use , the wheel ma y be wor k ed in both A and B direction. Operation with wire cup brush (optional accessory) CA UTION: • Check oper ation of br ush b y r unning tool with no load, insuring that no one is in front of or in line wit[...]

11 Operation with abrasive cut-off wheel (optional accessory) W ARNING: • When using an abrasiv e cut-off wheel, be sure to use only the special wheel guard designed fo r use with cut- off wheels. • NEVER use cut-off wheel f or side gr inding. During cutting operations, ne ver change the angle of the wheel. Placing side pressure on the cut-off [...]

12 recommended in this manual. Y our failure to do so could result in personal injur y to y ou and others. If you need an y assistance for more details regarding these accessories, ask your local Makita service center . C00162 2 3 4 5 6 7 8 2 9 10 11 3 12 5 1 005514 9564 9565 1G r i p 3 6 2 Wheel guard 3 Inner flange 45 4 Depressed center grinding [...]

13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy Street Fremont, CA 94538-5107 (510) 657-9881 14930 Northam Street La Mirada, CA 90638-5753 (714) 522-8088 4191A P ower Inn Rd. Sacramento , CA 95826 (916) 454-4768 767[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]