Makita AF501 инструкция обслуживания

SPECIFICATIONS 4 - 7 kgf/cm2G 160 - 100 PSIG) L MODEL AF501 246 mm x 57 mm x 225 mm 1.26 kg 19-11/16'' x 2-114" x 8-718") 12 78 Ibs! 100 pcs. 6.5 25 mm, 30 mm, 35 mm. 40 mm. 45 mm, 50 mm (l", 1-3/16", 1-318". 1-9/16", 1-314". 2") 1114") INSTRUCTION MANUAL Air pressure I Applicable length (Brad [...]

IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY, INCLUDING THE FOLLOWING: f? READ ALL INSTRUCTIONS. For personal safety and proper operation and main- tenance of the tool, read this instruction manual carefully before using the tool. Wear light but[...]

General Tool Handling Guidelines: 1. Always assume that the tool contains fasteners. 2.Do not point the tool toward yourself or anyone whether it contains fasteners or not. 3. Never depress the operating control unless the nosepiece of the tool is directed toward the workpiece. 4.Respect the tool as a working implement. 5. No horseplay. Sparks some[...]

There may be local regulations concerning noise which must be complied with by keeping noise levels within prescribed limits. In certain cases, shutters should be used to contain noise. Do not tamper with the tool or attempt to use it for other than nailing. Operate the tool within the specified air pressure of 4.0 - 7.0 kgf/cmZG (60 - 100 PSIG) fo[...]

Always check the tool for its overall condition and loose screws before operation. Tighten as required. Make sure the safety mechanism is in working order before operation. First, disconnect the hose from the tool and open the magazine. Turn the lock knob (lock pin) to make sure the trigger is locked and released alternately with every quarter turn[...]

Use only nails specified in this manual. The use of any other nails may cause malfunction of the tool. Do not permit those uninstructed to. use the tool. Make sure no one is nearby before nailing. Never attempt to nail from both the inside and outside at the same time. Nails may rip through and/or fly off, presenting a grave danger. Watch your foot[...]

On rooftops and other high locations, nail as you move forward. It is easy to lose your footing if you nail while inching backward. When nailing against perpendicular surface, nail from the top to the bottom. You can perform nailing operations with less fatigue by doing so. A nail will be bent or the tool can become jammed if you mistakenly nail on[...]

*When the air hose is connected, do not carry the tool with your finger on the trigger or hand it to someone in this condition. Accidental firing can be extremely dangerous. Handle the tool carefully as there is high pressure inside the tool that can be dangerous if a crack is caused by rough handling (dropping or striking). Do not attempt to carve[...]

z" Perform cleaning and maintenance right after finish- ing the job. Keep the tool in tip-top condition. Lubricate moving parts to prevent rusting and minimize friction related wear. Wipe off all dust from the parts. When not operating the tool, always lock the trigger by turning the lock knob (lock pin). This trigger operated tool is intended[...]

TOOL INSTALLATION INSTRUCTIONS AND USE Lubrication To insure maximum performance, install an air set (oiler, regulator, air filter) as close as possible to the tool. Adjust the oiler so that one drop of oil will be provided for every 50 nails. When an air set is not used, oil the tool with pneumatic tool oil by placing 2 (two) or 3 (three) drops in[...]

Load nails into the magazine so that the nail points will be set into the groove at the bottom of the maga- zine. Move the nails into the ejection slot as far as they will go. CAUTION : Always load the same type and size of nail into the magazine. If you load the tool with different types and/or sizes at the same time, a malfunction may result. To [...]

3. Loosen the three screws which secure the driver guide a half turn. 4. Turn the adjusting bolt until the desired depth of nailing can be obtained. The adjusting bolt moves 0.7 mm (1 /32") per turn. 5. Tighten the three screws while holding the driver guide so that the projection of the center plate contacts the adjusting bolt. 6. If nails ar[...]

I I .i Connecting air hose Lock the trigger. Slip the air socket of the air hose onto the air fitting on the nailer. Be sure that the air socket locks firmly into position when installed onto the air fitting. A hose coupling must be installed on or near the tool in such a way that the pressure reservoir will discharge at the time the air supply cou[...]

Hook The hook is convenient for hanging the tool tempo- rarily. This hook can be installed on either side of the tool. CAUTION : .Always lock the trigger and disconnect the hose when hanging the tool using the hook. Never hang the tool on a waist belt or the like. Dangerous accidental firing may result. Nails I Handle nail strips and their box care[...]

I Check regularly to see if there is sufficient pneumatic oil in the oiler of the air set. Failure to maintain suffi- cient lubrication will cause O-ring to wear quickly. Keep the air hose away from heat (over 60°C, over 140” F), away from chemicals (thinner, strong acids or alkalis). Also, route the hose away from obstacle which it may become d[...]