Makita Grinder 9077SL инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Angle Grinder 180 mm (7”) MODEL 9077SL DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to follo w Maintenance instructions may create a risk of electric shock or injury . USE PROPER EXTENSION CORD: Mak e sure your e xtension cord is in good condition. When using an e [...]

5 8. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock n ut. Damage to these par ts could result in wheel breakage. 9. NEVER use tool with wood cutting bl ades or other sawblades. Suc h blades when used on a grinder frequently kic k and cause loss of control leading to per sonal injury . 10. Hold the t[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Shaft lock CA UTION: • Ne ver actuate the shaft lock when the spindle is mo ving. The tool ma y be damaged. Press the shaft lock to pre vent spindle rotation when install- ing or removing accessori[...]

7 ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and unplugged befo re carr ying out any work on the tool. Installing side grip (handle) CA UTION: • Alwa ys be sure that the side grip is installed securely bef ore operation. Screw the side grip securely on the position of the tool as shown in the figure. Installing or remov[...]

8 T o tighten the lock nut, press the shaft lock firmly so that the spindle cannot re volve , then use the lock nut wrench and securely tighten clockwise . T o remove the wheel, f ollow the installation procedure in re verse. Installing or removing fle x wheel (optional accessory) W ARNING: • Alwa ys use supplied guard when flex wheel is on tool.[...]

9 • NEVER bang or hit grinding disc or wheel onto work. • A void bouncing and snagging the wheel, especially when working cor ners , shar p edges etc. This can cause loss of control and kickbac k. • NEVER use tool with wood cutting b lades and other sawb lades. Such blades when used on a g r inder frequently kick and cause loss of control lea[...]

10 NO TE: • When using wire cup brush, mount urethane washer to the spindle. It will mak e it easier to remove wire cup brush. Operation with wire wheel brush (optional accessory) CA UTION: • Check oper ation of wire wheel br ush b y r unning tool with no load, insuring that no one is in front of or in line with the wire wheel brush. • Do not[...]

11 Replacing carbon brushes When the resin insulating tip inside the carbon brush is e xposed to contact the commutator , it will automatically shut off the motor . When this occurs, both carbon brushes should be replaced. K eep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use on[...]

12 9077SL 1G r i p 3 8 2 Wheel guard 3 Inner flange 89 4 Depressed center grinding wheel/Multi-disc 5 Lock nut 5/8-40 6 Plastic pad 7 Flex wheel 8 Rubber pad 170 9 Abrasiv e disc 10 Sanding lock nut 5/8-48 11 Wire wheel brush 12 Urethane washer 14 13 Wire cup brush - Lock nut wrench 28 2 3 5 2 3 6 7 5 8 9 10 2 11 12 4 13 1 001185[...]

13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211 (501) 224-5733 CALIFORNIA 41850 Chris[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]